nach oben

Chinese Journal of Mechanical Engineering

Erschienen in:

Open Access 01.12.2018 | Original Article

Active Damping of Milling Vibration Using Operational Amplifier Circuit

verfasst von: Bashir Bala Muhammad, Min Wan, Yang Liu, Heng Yuan

Erschienen in: Chinese Journal of Mechanical Engineering | Ausgabe 1/2018

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Patentsuche

Aus

Abstract

The problem of chatter vibration is associated with adverse consequences that often lead to tool impairment and poor surface finished in a workpiece, and thus, controlling or suppressing chatter vibrations is of great significance to improve machining quality. In this paper, a workpiece and an actuator dynamics are considered in modeling and controller design. A proportional-integral controller (PI) is presented to control and actively damp the chatter vibration of a workpiece in the milling process. The controller is chosen on the basis of its highly stable output and a smaller amount of steady-state error. The controller is realized using analog operational amplifier circuit. The work has contributed to planning a novel approach that addresses the problem of chatter vibration in spite of technical hitches in modeling and controller design. The method can also lead to considerable reduction in vibrations and can be beneficial in industries in term of cost reduction and energy saving. The application of this method is verified using active damping device actuator (ADD) in the milling of steel.

1 Introduction

The modification of metal part into desired shape and size, for a different purpose in industries, are produced by milling. Such process can certainly be disturbed by chatter vibration, which leads to negative effects ranging from the poor surface finish, reduced work quality and high production cost to machine impairment [1, 2]. Chatter vibration severely disturbs the milling practice and it is caused by undesirable relative movement between a tool and a workpiece. Thus, to improve the quality of the workpiece, it is of great importance to study the chatter generation mechanism together with its control process. Therefore, this research will focus more attention on milling chatter vibration detection and its control process.

Primarily, identification of chatter using stability lobe diagram (SLD) is very critical in machining. In machine tools, chatter and non-chatter vibrations separate from each other using SLD, which is a series of interconnected lobes in term of axial depth of cut and spindle speed that demarcates the regions of chatter vibrations. Regions below the lobes mean stable chatter vibrations [3]. SLD can be developed in either time or frequency domains. It is much faster to develop SLD in the frequency domain than in time domain. Frequency response function (FRF) [4‐6], linear time-periodic function [7], and zero order approximation of the characteristics equation [8] are commonly employed to predict chatter vibrations in literature. In FRF, Fast Fourier transform (FFT) can determine the actual machining boundary where unstable cut show high amplitude with high vibration and stable cut show lower vibration with low amplitude [9]. Owing to the above deliberations, two important points, which increased chatter vibration in machining [4‐6, 10‐17] were identified as follows: an increase in depth of cut which move up vibration frequency and the effects of high spindle speed on shifting machine dynamic toward unstable cutting vibrations. Dos Santos and Coelho [4] improved the accuracy of chatter prediction in machine tools using the stability lobe diagram. Gagnol et al. [5] develop a spindle dynamic model for rotor equation using Timoshenko beam theory. Eynian [6] used Nyquist contour to predict the stability through dominant poles of the closed loop delay-differential equation for machining systems. Li et al. [10] established a comprehensive dynamic model of milling for stability analysis by considering regeneration, helix angle, and process damping. Solis et al. [11] used nondestructive trials to determine a new transfer function of the milling process for stability analysis. Altintas and Budak [12] and Altintas et al. [13] developed analytical methods for the predictions of chatter in milling. Soliman and Ismail [14] used PD fuzzy controller to limit the chatter indication. Quintana and Ciurana [15] experimentally determined stability lobe by increasing the depth of cut in feed direction. Tsai et al. [16] proposed acoustic signal feedback and spindle speed compensation for intelligent control application to avoid chatter vibration in milling process. Abele and Fiedler [17] created stability lobe of the milling process by considering the dynamic behavior of the system. In the past, efforts have been made by a quite number of researchers to study the problems of machining chatter vibrations [3]. Experimental and finite element (FE) model of machine tool were combined to investigate the vibrations [18, 19]. Kersting et al. [19] highlighted the effects of vibration on the workpiece, which focused on the feedback of workpiece displacement using FE. Dankena et al. [20, 21] related workpiece vibration to the workpiece material and workpiece structure. They pointed out that compound workpiece was a major cause of unfavorable workpiece performance, such as material height deviations, transition deviation at material joint, and surface roughness deviation, as compared to a single workpiece. Ma et al. [22‐25] attributed vibration of the flexible workpiece to the workpiece fixture, and they improved the stiffness of the workpiece by using magnetorheological (MR) fluid. Ma et al. [22] designed a flexible fixture to investigate the regenerative chatter based on the MR fluids. Ma et al. [23] also proposed a dynamic analytical model by considering fixture constraints and the damping factor. Zeng et al. [24] constructed the dynamic model of the workpiece-fixture-cutter system by using the cutting force and the fixture element as the disturbance input and control input, respectively [24]. Similarly, retrofittable intelligent active fixtures, capable of observing the process in real-time and exert adequate counter-excitations was reported in Ref. [25]. In spindle speed variation, workpiece vibrations are curtailed by selecting suitable spindle speed so that the excitation frequency corresponds to the workpiece resonance [26]. Active control is a process that utilized the actuator force to provide adequate damping force that suppresses chatter vibration [27]. It consumes considerable energy to derive the actuator.

Moreover, efforts were made to decrease the negative effects of regenerative chatter in machining [3, 28‐30]. Regenerative chatter occurs due to effects of interaction between previous and current cut [3]. Hayasaka et al. [28] employed the regenerative effects cancellation diagram in varied-helix end milling. Zhou et al. [29] related regenerative chatter to harmonic excitation. Moradi et al. [30] combined extremal algorithm and optimal control to suppress the regenerative chatter in machining.

Some techniques on active control were reported in Refs. [31‐35]. Control of vibrating actuator was considered using a PID controller [31]. Active control was proposed based on delayed state feedback control and discrete optimal control [32]. The effect of a fuzzy logic controller on active magnetic bearing was verified to regulate the spindle position in milling [33]. Long et al. [34] designed feedback control through a robust mixed sensitivity method by using two degrees of freedom (TDOF) workpiece holder. A proportional integral controller was employed for nonlinear stiffness function [35]. Astrom and Hagglund described detail description of proportional integral and derivative (PID) controllers and its application in control system [36]. Information describing the operational amplifier circuit and its application in filter, amplification, and control capabilities were explained [37‐39].

This is the major approach to resolve chatter vibration problem in the milling process via the operational amplifier circuit. Encouraged by the above consideration, a proportional-integral controller is proposed to suppress the chatter vibrations in the milling process. Milling test will be considered to investigate the effects of the proposed controller. This work contributes to minimizing chatter vibration and its negative consequences.

2 Modeling

2.1 Motion Equation of the System

This work developed control strategies that consider the chatter vibration of a flexible workpiece under both bending moment and cutting forces. The vibration of the workpiece is proportional to the perpendicular distance between the cutting force and the support point. Depending on the workpiece flexibility, the larger the perpendicular distance $\gamma$, the more the vibration. Figure 1 illustratively shows the bending displacement in the x-direction with the applied force. Eq. (1) relates the bending moment to the vibration.

$$\begin{aligned} m_{x} \ddot{\lambda }_{x} e^{ - \alpha t} + c_{x} \dot{\lambda }_{x} e^{ - \alpha t} + k_{x} \lambda_{x} e^{ - \alpha t} = \frac{{M_{x} }}{{\beta_{x} }}, \hfill \\ m_{y} \ddot{\lambda }_{y} e^{ - \alpha t} + c_{y} \dot{\lambda }_{y} e^{ - \alpha t} + k_{y} \lambda_{y} e^{ - \alpha t} = \frac{{M_{y} }}{{\beta_{y} }}, \hfill \\ \end{aligned}$$

(1)

where $M_{x}$ and $M_{y}$ are the bending moments in x- and y-axes. $\beta_{x}$ is the workpiece thickness thru x-axis, while $\beta_{y}$ is the workpiece thickness thru y-axis. α is the exponential decay constant. $\lambda_{x}$ is the bending displacement in x-axis, and $\lambda_{y}$ is the bending displacement in y-axis. $c_{x}$ and $c_{y}$ are modal damping in x- and y-directions.

The vibration between cutting forces can be expressed as follows.

$$\begin{aligned} m_{x} \ddot{x} + c_{x} \dot{x} + k_{x} x = F_{x} , \hfill \\ m_{y} \ddot{y} + c_{y} \dot{y} + k_{y} y = F_{y} , \hfill \\ \end{aligned}$$

(2)

where $F_{x}$ and $F_{y}$ are the cutting forces in x- and y-directions. $m_{x}$ and $m_{y}$ are modal masses in x- and y-directions. $k_{x}$ and $k_{y}$ are modal stiffness in x- and y-directions.

Combining Eq. (1) with Eq. (2) gives

$$\begin{aligned} \varvec{M}\left[ {\begin{array}{*{20}c} {\ddot{x} + \ddot{\lambda }_{x} e^{ - \alpha t} } & 0 \\ 0 & {\ddot{y} + \ddot{\lambda }_{y} e^{ - \alpha t} } \\ \end{array} } \right] + \varvec{C}\left[ {\begin{array}{*{20}c} {\dot{x} + \dot{\lambda }_{x} e^{ - \alpha t} } & 0 \\ 0 & {\dot{y} + \dot{\lambda }_{y} e^{ - \alpha t} } \\ \end{array} } \right] + \hfill \\ \varvec{K}\left[ {\begin{array}{*{20}c} {x + \lambda_{x} e^{ - \alpha t} } & 0 \\ 0 & {y + \lambda_{y} e^{ - \alpha t} } \\ \end{array} } \right] = \left[ {\begin{array}{*{20}c} {F_{x} } & 0 \\ 0 & {F_{y} } \\ \end{array} } \right] + \left[ {\begin{array}{*{20}c} {\frac{{M_{x} }}{{\beta_{x} }}} & 0 \\ 0 & {\frac{{M_{y} }}{{\beta_{y} }}} \\ \end{array} } \right], \hfill \\ \end{aligned}$$

(3)

where $\varvec{M}{ = }\left[ {\begin{array}{*{20}c} {m_{x} } & 0 \\ 0 & {m_{y} } \\ \end{array} } \right]$, $\varvec{C}{ = }\left[ {\begin{array}{*{20}c} {c_{x} } & 0 \\ 0 & {c_{y} } \\ \end{array} } \right]$, $\varvec{K}{ = }\left[ {\begin{array}{*{20}c} {k_{x} } & 0 \\ 0 & {k_{y} } \\ \end{array} } \right]$.

2.2 Controller Design

Actuator action is regulated by the controller. The designed controller depends on the property of the system model and a vibration signal from the sensor. During the dynamic milling process, the controller receives a dynamic vibration signal from the sensor, which allows the controller to initiate a direct control action. This means an increase in positive error result to increase positive control output, and likewise, increase negative error result to increase negative control output. The stability of the controller is obtained by determining the close loop stability of characteristics equation, which has a negative real part. The range of controller value is determined from the controller gains that give stabilizing controller for the smooth running of the control system.

$$G = \frac{{\mathop \sum \nolimits_{i = 1}^{n} a_{i} s^{ - i} }}{{\mathop \sum \nolimits_{i = 1}^{p} b_{i} s^{ - i} }},$$

(4)

$$\frac{{\mathop \sum \nolimits_{i = 1}^{n} a_{i} s^{ - i} }}{{\mathop \sum \nolimits_{i = 1}^{p} b_{i} s^{ - i} }}\left[ {\frac{{K_{p} M_{x} M_{y} s + k_{i} }}{s}} \right] = - 1.$$

(5)

The system transfer function is represented in the simplified form in Eq. (4). Proportional gain $K_{p}$ and integral gain $k_{i}$ are obtained from the system Eq. (5) as follows:

$$K_{p} = - \frac{{\mathop \sum \nolimits_{i = 1}^{p} b_{i} s^{ - i} }}{{M_{x} M_{y} \mathop \sum \nolimits_{i = 1}^{n} a_{i} s^{ - i} }},$$

(6)

$$k_{i} = - \frac{{s\mathop \sum \nolimits_{i = 1}^{p} b_{i} s^{ - i} }}{{\mathop \sum \nolimits_{i = 1}^{n} a_{i} s^{ - i} }}[1 + \frac{1}{{M_{y} }}].$$

(7)

These gains provide regulatory force to compensate the vibration of the workpiece.

2.3 Proportional Integral Controller Circuit Realization Using Operational Amplifier

An operational amplifier is an integrated circuit made of transistors and resistors to amplify or attenuate the input signal [38]. Firstly, two basic amplifiers will be described as follows.

2.3.1 Proportional Inverting Amplifier

The proportional inverting amplifier is an amplifier that amplifies the input signal based on the resistance gain. The signal is applied through inverting input amplified by the gain. The non-inverting input is grounded.

2.3.2 Integral Amplifier

In the integral amplifier, the capacitor is used instead of a resistor in the feedback path. This results in an operational amplifier that is time integral of the input signal.

A proportional integral controller is organized using the above amplifiers configuration: This is the combination of proportional and integral control action. The circuit representation of the proportional integral controller based on the operational amplifier is presented in Figure 2.

In Figure 2, $R_{1}$ and $R_{2}$ are resistors, $c_{0}$ is a capacitor, $U$ is the output voltage, and $U_{i}$ is the input voltage.

$$U = - \frac{{R_{2} }}{{R_{1} }}U_{i} - \frac{1}{{sC_{0} R_{1} }}U_{i}$$

(8)

Proportional integral amplifier gain is given by:

$$\frac{U}{{U_{i} }} \triangleq G_{c} = - \frac{{R_{2} + {1 \mathord{\left/ {\vphantom {1 {sc_{0} }}} \right. \kern-0pt} {sc_{0} }}}}{{R_{1} }}.$$

(9)

The proportional gain and integral gain are represented as Eq. (10):

$$K_{p} = \frac{{R_{2} }}{{R_{1} }},\,k_{i} = \frac{1}{{sc_{0} R_{1} }}$$

(10)

2.3.3 Anti-Windup

Properties of Zener diode was described [40]. Zener diode acts as low resistance in a forward path and built-up in reverse path till it goes into breakdown voltage $U_{z}$. Here, $U_{z}$ is Zener breakdown voltage. In this work, a Zener diode will be employed to regulate the output voltage of the proportional integral controller from exceeding the actuator limits (saturation). When a positive voltage from the sensor output is applied across the controller input $U_{i}$, ZD1 will be open up to 10 V (with ZD2 low resistance) and the voltage across the amplifier output will not exceed 10V ($U \le 10{\text{V}}$). Likewise when the negative voltage is applied across the terminal$U_{i}$, ZD2 will be open up to −10 V (with ZD1 low resistance) and the voltage across the output $U$will not exceed −10 V ($U \le - 10{\text{ V}}$). ZD1 and ZD2 are Zener diodes with $U_{z}$=10 V (shown in Figure 3).

2.4 Active Damping Actuator

The active damping actuator (ADD) consists of an accelerometer and actuator. The accelerometer detects the vibration signal of the structure and sends it to a control unit, which generates the control force according to the designed control law. The actuator is equipped with actuating mass, spring and damper. The actuating control force from the controller enhances the stiffness and damping to resist the vibration of the workpiece. During dynamic control process, an accelerometer detects the displacement of the workpiece and sends the signals to the external control unit, which generates the control force that derived the actuator. Figure 4 shows the schematic diagram of the active damping actuator. Where G_c is the controller; γ is the displacement vector; F_a is the control force vector; m₁, k₁ and c₁ are the mass, stiffness and damping coefficient.

3 Experimental Verification

This experiment is equipped with a data acquisition system (DAQ), a microphone, a proportional integral control circuit, and a personal computer. Actuator damping force is obtained from the active damping device (ADD-45N) based on the designed control low. An accelerometer present in the ADD allows the detection of displacement signals from the workpiece. The experimental setup is shown in Figure 5. The experiment consists of three separate processes, which are milling, control, and data acquisition process. The milling process is conducted at three different spindle speeds and using different depths of cut. The spindle speeds are at 1500 r/min, 2500 r/min, and 3000 r/min. The depths of cut are 1 mm, 1.3 mm, and 2.5 mm. The milling parameters are as follows: N (number of teeth) = 4, a_e (radial depth of cut) = 1 mm, feed rate=0.0750 mm/tooth. The data acquisition system records the signals showing the difference between controlled and uncontrolled vibrations of the system. The proportional integral control circuit is realized using an operational amplifier. The main aim of this control is damping the workpiece vibration signal. In Data acquisition process, CutPro^TM software, which was used in Ref. [41], is also used to acquire the sound signal (i.e., workpiece vibration signal) using data acquisition system (DAQ) at a sampling rate of 5120 Hz. Figure 5 shows the input and output of the control circuit. The input is from the sensor that detects workpiece vibration while the output is control signal that goes to the damping actuator. Table 1 shows the dynamic parameters of the system. In Table 1, the modal stiffness of the workpiece is 2.03×10⁷ N/m, and the stiffness of the actuator, k₁=6130 N/m. Modal mass of the workpiece is 4.4725 kg, while mass of the actuator, i.e., m₁=2.2 kg.

Table 1

Dynamic parameters of the experimental system

Serial number	Frequency (Hz)	Damping ratio	Stiffness (N/m)	Mass (kg)
1	339	0.006865	2.03×10⁷	4.4725
2	-	0.15	6130	2.2

Note: ‘1’ represents modal parameter of the workpiece, while ‘2’ represents actuator parameter from datasheet

4 Results

Figures 6, 7, 8, 9 show the comparisons before and after usage of the proposed method. Figure 6 displays the effect of the planned scheme at spindle speed of 1500 r/min. Figure 7 described the outcome of the recommended system at spindle speed of 2500 r/min. In this figure, axial depths of cut of 1 mm, 1.3 mm and 2.5 mm are considered in Figures 7(a), (b) and (c). Figure 8 presents the result of the suggested technique at spindle speed of 3000 r/min and different axial depth of cut. Figure 9 illustrates the overall effect of the projected process under different cutting conditions. The magnitude of the FFT of the measured signals could reflect the vibration intensity. Consequently, the magnitude of the FFT signals can be selected as the criteria to characterize the dynamic vibration. To obviously show the effect of the proposed method, the percentages of vibration reduction under different cutting parameters was calculated and pictured in Figure 9.

From the above comparisons, it can be seen that the proposed method can well reduce the vibrations under different cutting conditions. Chatter due to vibration of a flexible workpiece resulting from the bending displacement is a major obstacle affecting the quality of a workpiece in the milling process. However, bending moment has not been given attention in the literature. This work has provided a means of reducing the severity of the situation. The work considered the spindle speed variation and depth of cut variation. The actuator provides a counterbalance force that minimizes the displacement due to the bending moment, as shown in the figures.

5 Conclusions

The work has presented the active control method to suppress chatter vibration in the milling process. The effect of the proposed method in active control of the workpiece vibration has been verified at different depths of cut and spindle speeds. The chatter vibration is suppressed in the milling experiment based on the designed method. The work has contributed to planning a novel approach that addresses the problem of chatter vibration in spite of technical hitches in modeling and controller design. This method can also lead to considerable reduction in chatter vibration that can be beneficial in industries in term of cost reduction and energy saving. Milling at a different depth of cut and spindle speed is accomplished to illustrate the effect of the proposed method. The research has provided a novel method of improving workpiece quality; this is achieved through reduction of workpiece vibration by using an analog proportional-integral controller.

Authors’ Contributions

M. Wan was in charge of the whole trial; B.B. Muhammad wrote the manuscript; Y. Liu and H. Yuan assisted with sampling and laboratory analyses. All authors read and approved the final manuscript.

Authors’ Information

Bashir Bala Muhammad, is currently a PhD candidate at School of Mechanical Engineering, Northwestern Polytechnical University, China.

Min Wan, is currently a professor at School of Mechanical Engineering, Northwestern Polytechnical University, China.

Yang Liu, is currently a PhD candidate at School of Mechanical Engineering, Northwestern Polytechnical University, China.

Heng Yuan, is currently a PhD candidate at School of Mechanical Engineering, Northwestern Polytechnical University, China.

Acknowledgements

The authors sincerely thanks to Mr. Y.C. Ma and Dr. Y. Yang for their critical discussion and reading during manuscript preparation.

Competing Interests

The authors declare no competing financial interests.

Funding

This research has been supported by National Natural Science Foundation of China (Grant No. 51675440) and Fundamental Research Funds for the Central Universities of China (Grant no. 3102018gxc025).

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Vorheriger Artikel Design of Lattice Structures Using Local Relative Density Mapping Method

Nächster Artikel A Local Region Molecular Dynamics Simulation Method for Nanoscale Sliding Contacts

[1[.

Y Altintas. Manufacturing Automation. New York: Cambridge University Press, 2012.

[2]

M Luo, J Mei, D Zhang. Time-domain modeling of a cutter exiting a workpiece in the slot milling process. Chinese Journal of Aeronautics, 2016, 29(6): 1852–1858.CrossRef

[3]

B B Muhammad, M Wan, J Feng, et al. Dynamic damping of machining vibration: a review. International Journal of Advanced Manufacturing Technology, 2017, 89(9–12): 2935–2952.CrossRef

[4]

R G dos Santos, R T Coelho. A contribution to improve the accuracy of chatter prediction in machine tools using the stability lobe diagram. Journal of Manufacturing Science and Engineering, 2004, 136(2): 021005(1–7).

[5]

V Gagnol, B C Bouzgarrou, P Ray, et al. Stability-based spindle design optimization. Journal of Manufacturing Science and Engineering, 2007, 129(2): 407–415.CrossRef

[6]

M Eynian. Frequency domain study of vibrations above and under stability lobes in machining systems. International Conference on High Performance Cutting, HPC2014, 2014: 164–169.CrossRef

[7]

R S Hall, M N Wereley. Generalized nyquist stability criterion for linear time periodic systems. American Control Conference, 1990: 1518–1525.

[8]

I Minis, R Yanushevsky. A new theoretical approach for the prediction of machine tool chatter in milling. Journal of Engineering for Industry, 1993, 115(1): 1–8.CrossRef

[9]

M Wan, Y C Ma, J Feng, et al. Study of static and dynamic ploughing mechanisms by establishing generalized model with static milling forces. International Journal of Mechanical Sciences, 2016, 114: 120–131.CrossRef

[10]

Z Li, Y Sun, D Guo. Chatter prediction utilizing stability lobes with process damping in finish milling of titanium alloy thin-walled workpiece. International Journal of Advanced Manufacturing Technology, 2017, 89(9–12): 2663–2674.CrossRef

[11]

E Solis, C R Peres, J E Jiménez, et al. A new analytical-experimental method for the identification of stability lobes in high-speed milling. International Journal of Machine Tool and Manufacture, 2004, 44(14): 1591–1597.CrossRef

[12]

Y Altintas, E Budak. Analytical prediction of stability lobes in milling. Manufacturing Technology, 1995, 44(1): 357–362.

[13]

Y Altintas, E Shamoto, P Lee, et al. Analytical prediction of stability lobes in ball end milling. Manufacturing Technology, 1999, 121(4): 586–592.

[14]

E Soliman, F Ismail. A new method for the identification of stability lobes in machining. International Journal of Machine Tools and Manufacture, 1997, 37(6): 763–774.CrossRef

[15]

G Quintana, J Ciurana, D Teixidor. A new experimental methodology for identification of stability lobes diagram in milling operations. International Journal of Machine Tool and Manufacture, 2008, 48(15): 1637–1645.CrossRef

[16]

N C Tsai, D C Chen, R M Lee. Chatter prevention for milling process by acoustic signal feedback. International Journal of Advanced Manufacturing Technology, 2010, 47(9–12): 1013–1021.CrossRef

[17]

E Abele, U Fiedler. Creating stability lobe diagrams during milling. Manufacturing Technology, 2004, 53(1): 309–312.

[18]

S Pedrammehr, H Farrokhi, S A K Rajab, et al. Modal analysis of the milling machine structure through FEM and experimental test. Advanced Materials Research, 2012, 383–390: 6717–6721.

[19]

P Kersting, D Biermann. Simulation concept for predicting workpiece vibrations in five-axis milling. Machining Science and Technology, 2009, 13(2): 196–209.CrossRef

[20]

B Denkena, E Hasselberg. Influence of the cutting tool compliance on the workpiece surface shape in face milling of workpiece compounds. 15th CIRP Conference on Modelling of Machining Operations, 2015: 7–12.CrossRef

[21]

B Denkena, J Kohler, E Hasselberg. Modeling of workpiece shape deviations in face milling of parallel workpiece compounds. 14th CIRP Conference on Modeling of Machining Operations (CIRP CMMO), 2013: 176–181.CrossRef

[22]

J Ma, D Zhang, B Wu, et al. Vibration suppression of thin-walled workpiece machining considering external damping properties based on magnetorheological fluids flexible fixture. Chinese Journal of Aeronautics, 2016, 29(4): 1074–1083.CrossRef

[23]

J Ma, D Zhang, B Wu, et al. Stability improvement and vibration suppression of the thin-walled workpiece in milling process via magnetorheological fluid flexible fixture. Chinese Journal of Aeronautics, 2017, 88(5–8): 1231–1242.

[24]

S Zeng, X Wan, W Li, et al. A novel approach to fixture design on suppressing machining vibration of flexible workpiece. International Journal of Machine Tools and Manufacture, 2012, 58: 29–43.CrossRef

[25]

L Sallese, G Innocenti, N Grossi, et al. Mitigation of chatter instabilities in milling using an active fixture with a novel control strategy. International Journal of Advanced Manufacturing Technology, 2017, 89(9–12): 2771–2787.CrossRef

[26]

S Bolsunovsky, V Vermel, G Gubanov, et al. Reduction of flexible workpiece vibrations with dynamic support realized as tuned mass damper. Committee of the 14th CIRP Conference on Modeling, 2013: 230–234.CrossRef

[27]

Y Yang, D Xu, Q Liu, Vibration suppression of thin-walled workpiece machining based on electromagnetic induction. Materials and Manufacturing Processes, 2015, 30(7): 829–835.CrossRef

[28]

T Hayasaka, A Ito, E Shamoto. Generalized design method of highly-varied-helix end mills for suppression of regenerative chatter in peripheral milling. Precision Engineering, 2017, 48: 45–59.CrossRef

[29]

X Zhou, W Wang, J Lin. Harmonic retrieval of regenerative machining chatter responses. Mechanical Systems and Signal Processing, 2013, 41(1–2): 679–690.CrossRef

[30]

H Moradi, G Vossoughi, M R Movahhedy, et al. Suppression of nonlinear regenerative chatter in milling process via robust optimal control. Journal of Process Control, 2013, 23(5): 631–648.CrossRef

[31]

B B Muhammad, M H Rahman, M R Ahmad, et al. A novel model of PZT actuator and its application in hysteresis and vibration controls. Jurnal Teknologi, 2016, 78(6–13): 1–8.

[32]

S Long, S Ren, P Zheng. Delayed state feedback control for milling process. IUTAM Symposium on Nonlinear and Delayed Dynamics of Mechatronic Systems, 2017: 115–122.CrossRef

[33]

N C Tsai, L W Shih, R M Lee. Spindle vibration suppression for advanced milling process by using self-tuning feedback control. International Journal of Advanced Manufacturing Technology, 2010, 48(1–4): 1–10.CrossRef

[34]

X Long, H Jiang, G Meng. Active vibration control for peripheral milling processes. Journal of Materials Processing Technology, 2013, 213(5): 660–670.CrossRef

[35]

M Kassem, Z Yang, Y Gu, et al. Realization of artificial nonlinear spring with controllable stiffness. International Journal of Applied Mechanics, 2017, 9(5): 1750119(1-22).

[36]

K J Astrom, T Hagglund. PID controllers: Theory, design, and tuning. North Carolina: Instrument Society of America, 1995.

[37]

J J Cathey. Theory and problems of electronic devices and electronic circuits. USA: Schaum’s Outline Series, McGraw Hill, 2002.

[38]

B M Wilamowski, J D Irwin. Fundamentals of industrial electronics. Florida: CRC Press, 2011.

[39]

W G Jung. Op Amp applications handbook. Burlington: Newnes/Elsevier and Analogue Device Inc., 2005.

[40]

B L Theraja, A K Theraja. A textbook of electrical technology. New Delhi: S. Chand and Co Ltd, 2005.

[41]

M Wan, T Q Gao, J Feng, et al. On improving chatter stability of thin-wall milling by prestressing. Journal of Materials Processing Technology, 2019, 264: 32–44.CrossRef

Titel: Active Damping of Milling Vibration Using Operational Amplifier Circuit
verfasst von: Bashir Bala Muhammad
Min Wan
Yang Liu
Heng Yuan
Publikationsdatum: 01.12.2018
Verlag: Springer Singapore
Erschienen in: Chinese Journal of Mechanical Engineering / Ausgabe 1/2018
Print ISSN: 1000-9345
Elektronische ISSN: 2192-8258
DOI: https://doi.org/10.1186/s10033-018-0291-9

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht