Weitere Kapitel dieses Buchs durch Wischen aufrufen
Structural joints are where the durability, or lack of durability, is usually most evident in composite structural response to combined environmental effects and mechanical loads. The overall durability or degradation of a structural joint is a function of the response of all of the constituents of the joint: individual joined members, fasteners and/or adhesive, shims, sealants, coatings, etc. The objective of this chapter shall be to provide a brief overview of observed durability behavior of composite structural joints, experimental techniques for exploring the durability of joints, analytical predictive methods, and certain empirical case studies, mainly from the aerospace industry. The chapter is logically divided into separate bolted and bonded sections.
Bitte loggen Sie sich ein, um Zugang zu diesem Inhalt zu erhalten
Sie möchten Zugang zu diesem Inhalt erhalten? Dann informieren Sie sich jetzt über unsere Produkte:
J. R. Davis, ed., ASM Metals Handbook, Desk Edition, 2 nd Ed., ASM Int’l, Metals Park, OH (1998).
Kinloch, A., Developments in Adhesives – 2, Applied Science Publishers (1981).
Kulak, Geoffry L. et al., Guide to Design Criteria for Bolted and Riveted Joints, American Institute of Steel Construction, Chicago, IL (2001).
Bickford, John H., An Introduction to the Design and Behavior of Bolted Joints, Third Edition, Marcel Dekker, Inc., New York, NY (1995).
Annual Book of ASTM Standards, “Space Simulation; Aerospace and Aircraft; High Modulus Fibers and Composites,” Vol 15.03, ASTM International, 100 Barr Harbor Dr, West Conshohocken, PA (revision issued annually).
Annual Book of ASTM Standards, “Plastics,” Vols 08.01 – 08.03, ASTM International, 100 Barr Harbor Dr, West Conshohocken, PA (revision issued annually).
Annual Book of ASTM Standards, “Adhesives,” Vol 15.06, ASTM International, 100 Barr Harbor Dr, West Conshohocken, PA (revision issued annually).
Annual Book of ASTM Standards, “Fasteners,” Vol 15.08, ASTM International, 100 Barr Harbor Dr, West Conshohocken, PA (revision issued annually).
Fastener Test Methods, “NASM1312 Standard Practice,” Aerospace Industries Assoc., Washington, DC (2002).
DoD Composite Materials Handbook, “Vol. 1 Polymer Matrix Composites Guidelines for Characterization of Structural Materials,” MIL-HDBK-17-1 F (17 June, 2002).
DoD Composite Materials Handbook, “Vol. 3 Materials, Usage, Design, and Analysis,” MIL-HDBK-17-3 F (12 Dec, 2001).
Metallic Material Properties Development and Standardization, MMPDS02, Battelle Memorial Institute, Columbus, OH (April, 2005).
Pinnell, M., 1995, “A Parametric Study of the Factors Affecting the Open and Filled Hole Performance of Fiber Reinforced Composite Materials,” Ph. D Dissertation, University of Dayton, Dayton OH, p 141.
Altman, L. K., Reddy, D. J., and Moore, H., 2000, “Fail-Safe Approach for the V-22 Composite Proprotor Yoke,” Composite Structures: Theory and Practice, ASTM STP 1383, P. Grant and C. Q. Rousseau, eds., American Society of Testing Materials, West Conshohocken, PA, pp. 131–139.
Eisenmann, J., Rousseau, C. “Practical Fatigue Analysis of Shear-Loaded Fasteners,” Proc. 9 th Int’l Fatigue Conf., Atlanta, GA (14 – 19 May, 2006).
Lekhnitskii, S. G., 1954, “Stress Distribution in an Anisotropic Plate with an Elliptic Elastic Core (plane problem), ” Inzhenernyy sbornic, v. XIX., Moscow.
Crews, J. H. Jr., Hong, C. S. and Raju, I. S., 1981, “Stress Concentration Factors for Finite Orthotropic Laminates with a Pin-Loaded Hole,” NASA Technical Paper 1862.
Lessard, B. L. and Shokrieh, M. M., 1995, “Two-Dimensional Modeling of Composite Pinned-Joint Failure,” J. of Composite Materials, Vol. 29, No. 5, pp. 671–697. CrossRef
Hamada, H., Haruna, K. and Maekawa, Z.-I., 1995, “Effect of Stacking Sequences on Mechanically Fastened Joint Strength in Quasi-Isotropic Carbon-Epoxy Laminates,” J. of Composite Technology & Research, July, Vol. 17 (3), pp. 249–259. CrossRef
Collings, T.A., 1977,” The Strength of Bolted Joints in Multi-Directional CFRP Laminates,” Composites, January, Vol. 8 (1), pp. 43–54. CrossRef
Quinn, W. J. and Matthews, F. L., 1977, “The Effect of Stacking Sequence on the Pin-bearing Strength in Glass Fiber Reinforced Plastics,” Journal of Composite Materials, April, Vol. 11 (2), pp. 139–145. CrossRef
Shyprykevich, P., 1995, “Characterization of Bolted Joint Behavior: MIL-HDBK-17 Accomplishments at Standardization,” J. of Composite Technology & Research, July, Vol. 17 (3), pp. 260–270. CrossRef
Smith, P. A. and Pascoe, K. J., 1986, “The Effect of Stacking Sequence on the Bearing Strengths of Quasi-isotropic Composite Laminates,” Composite Structures, Vol. 6, pp. 1–20. CrossRef
Marshall, I. H., Arnold, W. S., Wood, J. and Mousley, R. F., 1989, “Observations on Bolted Connections in Composite Structures,” Composite Structures, Vol. 13, pp. 133–151. CrossRef
Arnold, W. S., Marshall, I. H. and Wood, J., 1989, “A Finite Element Assessment of Clamping Effects in Composite Bolted Joints,” J. of Aerospace Engineering, Proc Instn Mech Engrs, Vol. 203, pp. 39–45. CrossRef
Matthews, F. L., Wong, C. M. and Chryssafits, S., 1982, “Stress Distribution Around a Single Bolt in Fibre-Reinforced Plastic,” Composites, July 1982, pp. 316–322. CrossRef
Chen, W.-H., Lee, S.-S. and Yeh, J.-T., 1995, “Three Dimensional Contact Stress Analysis of a Composite Laminate with Bolted Joint,” Composite Structures, Vol. 30, pp. 287–297. CrossRef
Folias, E. S., 1989, “On the Interlaminar Stresses of a Composite Plate Around the Neighborhood of a Hole,” Int. J. Solids Structures, Vol. 25, pp. 1193–1200. CrossRef
Iarve, E. V., 1996, “Spline Variational Three Dimensional Stress Analysis of Laminated Composite Plates with Open Holes,” Int. J. of Solids and Structures, Vol. 33, No. 14, pp. 2095–2117. CrossRef
Iarve, E. V., 1995a, “Three Dimensional Stress Analysis of Fastener Hole Composites,” Proceedings of the ASME Materials Division, MD-Vol. 69–1, 1995 IMECE, ASME.
Iarve, E. V., 1995b, “Stress Analysis in Laminated Composites with Fastener Holes,” Proceedings of the ASC Tenth Technical Conference, Santa Monica, CA, October 18–20, Technomic Publishing Company, pp. 408–419.
Iarve, E. V., 1994, “On the Accuracy of Interlaminar Stress Calculation in Vicinity of an Open Hole in Composite by Use of the Spline Variational Technique,” Proceedings of the ASC Ninth Technical Conference, Technomic Publishing Company, DE, September 20–22, pp. 797–806.
Iarve, E. V., 1993, “Interlaminar Stress Analysis in Compression Loaded Composite Plates Containing Open Hole,” Proceedings of the ASC Eighth Technical Conference, Technomic Publishing Company, Cleveland OH, October 19–21, pp. 1025–1034.
Wang, S. S. and Lu, X., 1993, “Three-Dimensional Asymptotic Solutions for Interlaminar Stresses Around Cutouts in Fiber Composite Laminates,” Mechanics of Thick Composites, AMD-Vol. 1962, pp. 41–50.
Iarve, E. V., 1997, “Three-Dimensional Stress Analysis in Laminated Composites with Fasteners Based on the B-spline Approximation,” Composites Part A, 28, pp. 559–571. CrossRef
Sihn, S., Iarve, E. V. and Roy, A. K., 2006, “Asymptotic Analysis of Laminated Composites with Countersunk Open- and Fastened-Holes,” Composites Science and Technology, 66(14), pp. 2479–2490. CrossRef
Iarve, E. V. and Pagano, N. J., 2001, “Singular Full-Field Stresses in Composite Laminates with Open Holes,” Int. J. Solids Struct., 38(1) pp. 1–28. CrossRef
Whitney, T. J., Iarve, E. V. and Brockman, R. A., 2004, “Singular Stress Fields Near Contact Boundaries in a Composite Bolted Joint,” Int J Solids Struct., 41(7), pp. 1893–1909. CrossRef
Iarve, E.V., Mollenhauer, D., Kim, R., 2005, “Theoretical and Experimental Investigation of Stress Redistribution in Open Hole Composite Laminates Due to Damage Accumulation,” Composites Part A, 36(2), pp. 163–171.
Camanho, P. P. and Matthews, F. L., 1999, “Stress Analysis and Strength Prediction of Mechanically Fastened Joints in FRP: A Review,” Composites Part A 28A, pp. 529–547.
Lee, J., 1983, “Three-Dimensional Finite Element Analysis of Damage Accumulation in Laminated Composite,” In Strength and Fracture in Composite Materials (175–186). G. C. Sih and V. P. Tamuz, eds. Latvia: Zinatne.
Gamble, K., Pilling, M. Pilling, and Wilson, A., 1995, “An Automated Finite Element Analysis of the Initiation and Growth of Damage in Carbon Fiber Composite Materials,” Composite Structures 32, pp. 275–285. CrossRef
Nguyen, B. N., 1997, “Three-Dimensional Modeling of Damage in Laminated Composites Containing a Central Hole,” J. Composite Materials 31(17), pp. 1672–1694. CrossRef
Camanho, P. P. and Matthews, F. L., 1999, “A Progressive Damage Model for Mechanically Fastened Joints in Composite Laminates,” J. Composite Materials 33, pp. 2248–2280. CrossRef
Chen, W. H. and Lee, S. S., 1995, “Numerical and Experimental Failure Analysis of Composite Laminates with Bolted Joints under Bending Loads,” J. Composite Materials 29(1), pp. 15–35. CrossRef
Tang, S. C., 1991, “A Progressive Failure Model for Composite Laminates Containing Openings,” J. Composite Materials 25, pp. 556–557.
Ye, L., 1988, “Role of Matrix Resin in Delamination Onset and Growth in Composite Laminates,” Composites Science and Technology 33, pp. 257–277. CrossRef
Pagano, N. J., Schoeppner, G. A., Kim, R. Y., and Abrams, F. L., 1998, “Steady-State Cracking and Edge Effects in Thermomechanical Transverse Cracking of Cross-Ply Laminates,” Composite Science and Technology 58, pp. 1811–1825. CrossRef
Schoeppner, G. A. and Pagano, N. J., 1999, “3-D Thermoelastic Moduli and Saturation Crack Density for Cross-Ply Laminates with Transverse Cracks,” Int. J. of Damage Mechanics. CrossRef
Iarve, E. V., 2003, “Mesh Independent Modeling of Cracks by Using Higher Order Shape Functions,” Int. J. Numer. Meth. Engng 56, pp. 869–882. CrossRef
Moes, N., Dolbow, J., and Belytschko, T., 1999, “A Finite Element Method for Crack Growth without Remeshing,” Int. J. Numerical Methods Engineering 46, pp. 131–150. CrossRef
Ling, D. S., Yang, Q. D., and Cox, B. N., 2009, “An Augmented Finite Element Method for Modeling Arbitrary Discontinuities in Composite Materials,” Int. J. of Fracture, 156, pp. 53–73.
Huynh, D. B. P. and Belytschko, T., 2009, “The Extended Finite Element Method for Fracture in Composite Materials,” Int. J. Numer. Meth. Engng., 77, pp. 214–239. CrossRef
ABAQUS, User Manual, Hibbitt, Karlson and Sorensen, Inc.
SAMCEF, User Manual, M5-V.5.1-94 Samtech S.A. (Belgium).
Green, B. G., Wisnom, M. R., Hallett, S. R., 2007 “An experimental investigation into the tensile strength scaling of notched composites,” Composites Part A, 38(3), pp. 867–878.
Wisnom, M. R. and Hallett, S. R., 2009, “The Role of Delamination in Strength, Failure Mechanism and Hole Size Effect in Open Hole Tensile Tests on Quasi-Isotropic Laminates,” Composites: Part A 40, pp. 335–342. CrossRef
Hallet, S. R., Green, B. G., Jiang, W. J., and Wisnom, M. R., 2009, “An Experimental and Numerical Investigation into the Damage Mechanisms in Notched Composites,” Composites: Part A, 40, pp. 613–624. CrossRef
Thoppul, S. D., Finegan, J. and Gibson, R., 2009, “Mechanics of Mechanically Fastened Joints in Polymer-Matrix Composite Structure – A Review,” Comp. Science and Techn., 69, pp. 301–329. CrossRef
Hasin, Z. and Rotem, A., 1973, “A Fatigue Failure Criterion for Fiber Reinforced Materials,” J. Composite Mater., (7), pp. 448–468. CrossRef
Philippidis, T. P. and Vassilopoulos, A. P., 2002, “Complex Stress State Effect on Fatigue Life of GRP Laminates, Part I, Experimental,” Int J Fatigue 24:8, pp. 13–30.
Philippidis, T. P., Vassilopoulos, A. P., 2002, “Complex Stress State Effect on Fatigue Life of GRP Laminates, Part II, Theoretical Formulation,” Int J. Fatigue 24:8, pp. 13–30.
Tserpes, K. I., Papanikos, P., and Labeas, G., 2004, “Fatigue Damage Accumulation and Residual Strength Assessment of CFRP Laminates,” Compos Struct 63:2, pp. 19–30. CrossRef
Sawicki, A. J., 2004, “Development of Compression Design Allow-ables for Composite Bolted Joints Using ASTM Standard D 6742,” in Joining and Repair of Composite Structures, ASTM STP 1455, K.T. Edward and H. Kim Eds., ASTM International, West Conshohocken, PA.
Sawicki, A. and Minguet, P., 2001, “Comparison of Fatigue Behavior for Composite Laminates Containing Open and Filled Holes,” Proceedings of the American Society for Composites 16 th Annual Technical Conference, Blacksburg, VA.
Shokrieh, M. M. and Lessard, L. B., 2000, “Progressive Fatigue Damage Modeling of Composite Materials, Part I: Modeling,” J Compos Mater 34(13), pp. 1056–116.
Shokrieh, M. M. and Lessard, L. B., 2000, “Progressive Fatigue Damage Modeling of Composite Materials, Part II: Material Characterization and Model Verification. J Compos Mater, 34(13), pp. 1056–116.
Adam, T., Dickson, R. F., Jones, C. J., Reiter, H. and Harris, B, 1986, “A Power Law Fatigue Life Damage Model for Fiber Reinforced Plastic Laminates,” Proceedings of Institution of Mechanical Engineers, Part C: Mechanical Engineering Science, 200(C3), pp. 155–166. CrossRef
Spearing, S. M., Beaumont, P. E. R. and Kortshot, M. T., 1992, “The Fatigue Damage Mechanics of Notched Carbon Fibre/PEEK Laminates,” Composites, 23(5), pp. 305–311. CrossRef
Van der Meer, F. P. and Sluys, L. J., 2009, “A Phantom Node Formulation with Mixed Mode Cohesive Law for Splitting in Laminates,” Int J Fracture DOI 10.1007/s10704-009-9344-5 (online).
Iarve, E. V., Gurvich, M. R., Mollenhauer, D. H., Rose, C. A. and DÃvila, C. G., 2011, “Mesh-Independent Matrix Cracking and Delamination Modeling in Laminated Composites,” Int. J. Numer. Meth. Engng, published online DOI: 10.1002/nme.3195.
Rousseau, C., 2000, “Primary Structure Composite Joining – Final Report,” USAAMCOM TR-01-D-03.
Baldan, A., 2004, “Review. Adhesively-Bolted Joints in Metallic Alloys, Polymers and Composite Materials: Mechanical and Environmental Durability Performance,” J. Material Science, 39, pp. 4729–4797. CrossRef
daSilva, L. F. M. and Ochsner, A., Eds, 2008, “Modeling of Adhesively Bonded Joints,” Springer-Verlag Berlin Heidelberg, 335p.
Hart-Smith, L. J., 1973, “Adhesive Single Lap Joints,” NASA CR 112236.
Adams, R. D., Cowap, J. W., Farquharson, G., Margary, G. M. and Vaughn, D., 2009, “The Relative Merits of the Boeing Wedge Test and the Double Cantilever Beam Test for Assessing the Durability of Adhesively Bonded Joints, with Particular Reference to the Use of Fracture Mechanics,” Int J of Adhesion & Adhesives, 29, pp. 609–620. CrossRef
Marceau, J. A., Moji, Y., McMillian, J. C., 1977, “A Wedge Test for Evaluating Adhesive-Bonded Surface Durability,” Adhesives Age, pp. 29–35.
Briskham, P. and Smith, G., 2000, “Cyclic Stress Durability Testing of Lap Shear Joints Exposed to Hot-Wet Conditions,” Int J of Adhesion & Adhesives, 20, pp. 33–38. CrossRef
Tay, T., 2002, “Characterization and Analysis of Delamination Fracture in Composites: An Overview of Developments from 1990 to 2001,” Appl. Mech. Rev., 55(6) (270 ref).
Pagano, N. J. and Schoeppner, G. A., 2000, “Delamination of Polymer Matrix Composites: Problems and Assessment,” In Comprehensive Composite Materials, 2, A Kelly and C. Zweben (eds.), Elsevier Science, Oxford, pp. 433–528. CrossRef
Rice, J. R., 1968, “A Path Independent Integral and the Approximate Analysis of Strain Concentration by Notches and Cracks,” J. Applied Mechanics, 35, pp. 379–386.
Parks, D. M., 1974, “A Stiffness Derivative Finite Element Technique for Determination of Crack Tip Stress Intensity Factors,” Int. J. Fracture, 10 (4), pp. 487–502. CrossRef
Mi, Y., Crisfield, M. A., and Davis, A. O., 1998, “Progressive Delamination Using Interface Elements,” J. of Composite Materials, 32 (14), pp. 1246–1270. CrossRef
Krueger, R., 2002, “The Virtual Crack Closure Technique: History, Approach and Applications,” NASA/CR-2002-211628.
Mabson, G., 2003, “Fracture Interface Elements,”, Mil Handbook 17 Committee Mtg, Charleston, SC.
Deobald, L. R., Mabson, G. E., Dopker, B., Hoyt, D. M., Baylor, J. and Greasser, D., 2007, “Interlaminar Fatigue Elements for Crack Growth Based on Virtual Crack Closure Technique,” 48 th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, Honolulu, HI.
Turon, A., Camanho, P. P., Costa, J., and Dávila, C. G., 2006, “A Damage Model for the Simulation of Delamination in Advanced Composites Under Variable-Mode Loading,” Mechanics of Materials, 38, pp. 1072–1089. CrossRef
Turon, A., Camanho, P. P., Costa, J., and Dávila, C. G., 2007, “Simulation of Delamination in Composites Under High-Cycle Fatigue,” Composites: Part A, doi:10.1016/j.compositesa.2006.11.009.
Bogdanovich, A. E. and Yushanov, S. P., 1998, “3-D Progressive Failure Analysis of Bonded Composite Joints,” In: AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, Vol. 2, New York: AIAA, pp. 1616–26.
Bogdanovich, A. E. and Yushanov, S. P., 1999, “Progressive Failure Analysis of Adhesive Bonded Joints with Laminated Composite Adherends,” Journal of Reinforced Plastics and Composites, Vol. 18, No. 18, pp. 1689–1707.
Gustafson, P.A. and Waas, A.M., 2009, “The Influence of Adhesive Constitutive Parameters in Cohesive Zone Finite Element Models of Adhesively Bonded Joints,” International Journal of Solids and Structures, In Press. CrossRef
Li, S., Thouless, M. D., Waas, A. M., Schroeder, J. A., and Zavattieri, P. D., 2005, “Use of Mode-I Cohesive-Zone Models to Describe the Fracture of an Adhesively-Bonded Polymer-Matrix Composite,” Composites Science and Technology 65, pp. 281–93. CrossRef
De Moura, M. F. S. R. and Chousal, J. A. G., 2006, “Cohesive and Continuum Damage Models Applied to Fracture Characterization of Bonded Joints,” Int. J. Mechanical Sciences, 48, pp. 493–503. CrossRef
Engelstad, S. P., Berry, O. T., Renieri, G. D., Deobald, L. R., Mabson, G. E., Dopker, B., Notterf, E. W., and Clay, S. B., 2005, “A High Fidelity Composite Bonded Joint Analysis Validation Study - Part I: Analysis,” 46 th AIAA/ASME/ASCE/ASC Structure, Structural Dynamics & Materials Conference, Austin, TX, AIAA, pp. 21–66.
Wollschlager, J. A., Gosse, J. H., Christensen, S., and Engelstad, S. P., 2002, “Current Developments in Composite Analysis and Failure Advocating an Advanced Composite Design Methodology,” Proceedings of SAMPE, Long Beach, CA.
Liljehadi, C. D. M., Crocombe, A. D., Wahab, M. A. and Ashcroft, I. A., 2007, “Modeling the Environmental Degradation of Adhesively Bonded Aluminum and Composite Joints Using a CZM Approach,” Int J Adhesion and Adhesives, 27(6), pp. 505–518. CrossRef
Quaresimin, M. and Ricotta, M., 2006, “Life Prediction of Bonded Joints in Composite Materials,” 28, pp. 1166–1176. CrossRef
Schom, J, Nyman, T, Blom, A. and Ansell, H., 2000, “A Numerical and Experimental Investigation of Delamination Behavior in the DCB Specimen,” Composites Sci and Technology, 60, pp. 173–184. CrossRef
Wahab, M. M. A., Ashcroft, I. A., Crocombe, A. D., Smith, P. A., “Finite Element Prediction of Fatigue Crack Propagation Lifetime in Composite Bonded Joints,” Composites Part A, 35, pp. 212–222.
Wahab, M. M., Ashcroft, I. A., Crocombe, A. D., Hughes, D. J. and Shaw, S. J., 2001, “The Effect of Environment on the Fatigue of Bonded Composite Joints. Part 2: Fatigue Threshold Prediction,” Composites Part A, 32, pp. 59–69. CrossRef
Breitzman, T. D., Iarve, E. V., Cook, B. M., Schoeppner, G. A. and Lipton, R. P., 2009, “Optimization of a Composite Scarf Repair Patch Under Tensile Loading,” Composites Part A, 40(12), pp. 1921–1930. CrossRef
Campilho, R. D. S. G., Moura, M. F. S. F. and Domingues, L.2007, “Using a Cohesive Damage Model to Predict the Tensile Behavior of CFRP Single-Strap Repairs,” Int. J. Solids and Structures, 45, pp. 1497–1512. CrossRef
Hua, Y., Crocombe, A. D., Wahab, M. A. and Ashcroft, I. A., 2008, “Continuum Damage Modeling of Environmental Degradation in Joints Bonded with EA9321 Epoxy Adhesive,” Int. J of Adhesion and Adhesives, 28, pp. 302–311. CrossRef
Martin, R. H. and Sage, G. N., 1986, “Prediction of the Fatigue Strength of Bonded Joints Between Multi-Directional Laminates of CFRP,” Composite Structures, 6, pp. 141–146. CrossRef
Casas-Rodriguez, J. P., Ashcroft, I. A. and Silbershmidt, V. V., 2008, “Delamination in Adhesively Bonded CFRP Joints: Standard Fatigue, Impact-Fatigue and Intermittent Impact,” Composites Sci. and Techn., 68, pp. 2401–2409. CrossRef
Erpolat, S., Ashcroft, I. A., Crocombe, A. D. and Abdel-Wahab, 2004, “Fatigue Crack Growth Acceleration Due to Intermittent Overstressing in Adhesively Bonded CFRP Joints,” Composites: Part A 35, pp. 1175–1183. CrossRef
Quaresimin, M. and Ricota, M., 2006, “Fatigue Behavior and Damage Evolution of Single Lap Bonded Joints in Composite Materials,” Composite Science and Technology, 66, pp. 176–187. CrossRef
Panigrahi, S. K. and Pradhan, B., 2008, “Onset and Growth of Adhesion Failure and Delamination Induced Damages in Double Lap Joint of Laminated FRP Composites,” Composites Structures, 85, pp. 326–336. CrossRef
- Durability of Structural Joints
Carl Q. Rousseau
Endel V. Iarve
- Springer US
- Chapter 12
in-adhesives, MKVS, Neuer Inhalt/© Zühlke, Hellmich GmbH/© Hellmich GmbH, Neuer Inhalt/© momius | stock.adobe.com