Weitere Artikel dieser Ausgabe durch Wischen aufrufen
The relation between microstructural inhomogeneity and thermal conductivity of a rheocast component manufactured from two different aluminum alloys was investigated. The formation of two different primary α-Al particles was observed and related to multistage solidification process during slurry preparation and die cavity filling process. The microstructural inhomogeneity of the component was quantified as the fraction of α 1-Al particles in the primary Al phase. A high fraction of coarse solute-lean α 1-Al particles in the primary Al phase caused a higher thermal conductivity of the component in the near-to-gate region. A variation in thermal conductivity through the rheocast component of 10% was discovered. The effect of an inhomogeneous temperature-dependent thermal conductivity on the thermal performance of a large rheocast heatsink for electronics cooling in an operation environment was studied by means of simulation. Design guidelines were developed to account for the thermal performance of heatsinks with inhomogeneous thermal conductivity, as caused by the rheocasting process. Under the modeling assumptions, the simulation results showed over 2.5% improvement in heatsink thermal resistance when the higher conductivity near-to-gate region was located at the top of the heatsink. Assuming homogeneous thermo-physical properties in a rheocast heatsink may lead to greater than 3.5% error in the estimation of maximum thermal resistance of the heatsink. The variation in thermal conductivity within a large rheocast heatsink was found to be important for obtaining of a robust component design.
Bitte loggen Sie sich ein, um Zugang zu diesem Inhalt zu erhalten
Sie möchten Zugang zu diesem Inhalt erhalten? Dann informieren Sie sich jetzt über unsere Produkte:
R.C. Chu, R.E. Simons, M.J. Ellsworth, R.R. Schmidt, and V. Cozzolino, Review of Cooling Technologies for Computer Products, IEEE Trans. Devices Mater. Reliab., 2004, 4(4), p 568–585 CrossRef
M. Tomovic and S. Wang, Product Realization: A Comprehensive Approach, Springer, US, 2008
J. Olofsson and I.L. Svensson, Closed Chain Simulations of a Cast Aluminium Component-Incorporating Casting Process Simulation and Local Material Characterization Into Stress-Strain Simulations, ISIJ Int., 2014, 54(2), p 259–265 CrossRef
A.A. Abrikosov and A. Beknazarov, Fundamentals of the Theory of Metals, Vol 1, North-Holland, Amsterdam, 1988
J.G. Kaufman, L. R. Elwin, Aluminum Alloy Castings: Properties, Processes, and Applications. ASM International, Materials Park, OH 44073-0002, 2004.
K. Azar, B. Tavassoli, Qpedia Thermal Management—Electronics Cooling Book, vol. 2. Advanced Thermal Solutions, 2008.
K.P. Keller, Cast Heatsink Design Advantages, Thermal and Thermomechanical Phenomena in Electronic Systems. The Sixth Intersociety Conf. ITHERM’98, 27–30 May, Seattle, Washington, USA, 1998, p 112–117.
M. Wessén, Rheogjutning av extremt tunnväggiga komponenter, Aluminium Scandinavia, No. 12012, p 16–17.
P. Olafsson, R. Sandstrom, and Å. Karlsson, Comparison of Experimental, Calculated and Observed Values for Electrical and Thermal Conductivity of Aluminium Alloys, J. Mater. Sci., 1997, 32(16), p 4383–4390 CrossRef
T. Grimmig, A. Ovcharov, C. Afrath, M. Bünck, and A. Bührig-Polaczek, Potential of the Rheocasting Process, Demonstrated on Different Aluminum Based Alloy Systems, Solid State Phenom., 2006, 116, p 484–488 CrossRef
M. Payandeh, Rheocasting of Aluminium Alloys: Slurry Formation, Microstructure, and Properties, Licentiate Thesis, Dissertation series No. 6, Jönköping University, Jönköping, 2015.
A. Bar-Cohen, M. Iyengar, and A.D. Kraus, Design of Optimum Plate-Fin Natural Convective Heat Sinks, J. Electron. Pack., 2003, 125(2), p 208–216 CrossRef
J. Parry, R.B. Bornoff, P. Stehouwer, L.T. Driessen, and E. Stinstra, Simulation-Based Design Optimization Methodologies Applied to CFD, IEEE Trans. Compon. Pack. Technol., 2004, 27(2), p 391–397 CrossRef
M. Wessén, H. Cao, The RSF Technology, A Possible Breakthrough for Semi-Solid Casting Processes. Int. Conf. of High Tech. Die Casting, 21–22 September, Vicenza, Italy, 2006.
M. Payandeh, A.E.W. Jarfors, and M. Wessén, Effect of Superheat on Melting Rate of EEM of Al Alloys During Stirring Using the RheoMetal Process, Solid State Phenom., 2013, 192, p 392–397
L. Vozár and W. Hohenauer, Flash Method of Measuring the Thermal Diffusivity. A Review, J. High Temp.-High Press., 2004, 36(3), p 253–264
H. Fredriksson and U. Åkerlind, Physics of Functional Materials, Wiley, NY, 2008 CrossRef
T.M. Tritt, Thermal Conductivity: Theory, Properties, and Applications, Kluwer Academic/Plenum, New York, 2004 CrossRef
Flotherm v. 10.1 user manual, Mentor Graphics Corporation ®, 2014.
J. Antony, Design of Experiments for Engineers and Scientists, Elsevier Science & Technology Books, 2014.
S. Ji, A. Das, and Z. Fan, Solidification Behavior of the Remnant Liquid in the Sheared Semisolid Slurry of Sn-15 wt.% Pb Alloy, Scripta Mater., 2002, 46(3), p 205–210 CrossRef
N. Saunders, The Application of Calculated Phase Equilibria to Multi-Component Aluminum Alloys, J. Japan Inst. Light Met., 2001, 51(3), p 141–150
Z. Guo and W. Sha, Quantification of Precipitate Fraction in Al-Si-Cu Alloys, Mater. Sci. Eng. A, 2005, 392, p 449–452 CrossRef
H. Kaufmann and P.J. Uggowitzer, Metallurgy and Processing of High Integrity Light Metal Pressure Castings, Fachverlag Schiele & Schoen, Berlin, 2007
R. Rana, R. Purohit, and S. Das, Reviews on the Influences of Alloying Elements on the Microstructure and Mechanical Properties of Aluminum Alloys and Aluminum Alloy Composites, Int. J. Sci. Res. Publ., 2012, 2(6), p 1–7
- Effect of Material Inhomogeneity on Thermal Performance of a Rheocast Aluminum Heatsink for Electronics Cooling
A. E. W. Jarfors
- Springer US
in-adhesives, MKVS, Zühlke/© Zühlke