nach oben

Journal of Materials Engineering and Performance

Erschienen in:

01.12.2015

Effect of Reprocessing and Accelerated Weathering on Impact-Modified Recycled Blend

verfasst von: V. Ramesh, Smita Mohanty, Manoranjan Biswal, Sanjay K. Nayak

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 12/2015

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Recovery of recycled polycarbonate, acrylonitrile butadiene styrene, high-impact polystyrene, and its blends from waste electrical and electronic equipment plastics products properties were enhanced by the addition of virgin polycarbonate and impact modifier. The optimized blend formulation was processed through five cycles, at processing temperature, 220-240 °C and accelerated weathering up to 700 h. Moreover, the effect of reprocessing and accelerated weathering in the physical properties of the modified blends was investigated by mechanical, thermal, rheological, and morphological studies. The results show that in each reprocessing cycle, the tensile strength and impact strength decreased significantly and the similar behavior has been observed from accelerated weathering. Subsequently, the viscosity decreases and this decrease becomes the effect of thermal and photo-oxidative degradation. This can be correlated with FTIR analysis.

Vorheriger Artikel The Effect of SiC Particle Addition During FSW on Microstructure and Mechanical Properties of AZ31 Magnesium Alloy

Nächster Artikel Simultaneously Enhancing the Ductility and Strength in a Hierarchical and Multiphase Nanolaminated TiZrAlV

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

R. Wang and Z. Xu, Recycling of Non-metallic Fractions from Waste Electrical and Electronic Equipment (WEEE): A Review, Waste Manag., 2014, 34(8), p 1455–1469CrossRef

S.N.M. Menikpura, A. Santo, and Y. Hotta, Assessing the Climate Co-benefits from Waste Electrical and Electronic Equipment (WEEE) Recycling in Japan, J. Clean. Prod., 2014, 74, p 183–190CrossRef

B.H. Robinson, E-Waste: An Assessment of Global Production and Environmental Impacts, Sci. Total Environ., 2009, 408(2), p 183–191CrossRef

H.G. Ni and E.Y. Zeng, Law Enforcement and Global Collaboration are the Keys to Containing E-Waste Tsunami in China, Environ. Sci. Technol., 2009, 43(11), p 3991–3994CrossRef

J. Cui and E. Forssberg, Mechanical Recycling of Waste Electric and Electronic Equipment: A Review, J. Hazard. Mater., 2003, 99(3), p 243–263CrossRef

F. Elmaghor, L. Zhang, R. Fan, and H. Li, Recycling of Polycarbonate by Blending with Maleic Anhydride Grafted ABS, Polymer, 2004, 45(19), p 6719–6724CrossRef

L.B. Brennan, D.H. Isaac, and J.C. Arnold, Recycling of Acrylonitrile-Butadiene-Styrene and High-Impact Polystyrene from Waste Computer Equipment, J. Appl. Polym. Sci., 2002, 86(3), p 572–578CrossRef

J. Kuczynski and R.W. Snyder, Physical Property Retention of PC/ABS Blends, J. Polym. Degrad. Stab., 1994, 43(2), p 285–291CrossRef

E.K. Karahaliou and P.A. Tarantili, Stability of ABS Compounds Subjected to Repeated Cycles of Extrusion Processing, Polym. Eng. Sci., 2009, 49(11), p 2269–2275CrossRef

10.

J.M. Perez, J.L. Vilas, J.M. Laza, S. Arnaiz, F. Mijangos, and E. Bilbao, Effect of Reprocessing and Accelerated Weathering on ABS Properties, J. Polym. Environ., 2010, 18(1), p 71–78CrossRef

11.

E.S. Sherman, A. Ram, and S. Kenig, Tensile Failure of Weathered Polycarbonate, Polym. Eng. Sci., 1982, 22(8), p 457–465CrossRef

12.

C.A. Pryde, Weathering of Polycarbonates: A Study of the Variables Involved, Polym. Prepr., 1984, 25, p 52–53

13.

V. Ramesh, M. Biswal, S. Mohanty, and S.K. Nayak, Recycling of Engineering Plastics from Waste Electrical and Electronic Equipments: Influence of Virgin Polycarbonate and Impact Modifier on the Final Performance of Blends, Waste Manag. Res., 2014, 32(5), p 379–388CrossRef

14.

H.E. Bair, D.J. Boyle, and P.G. Kelleher, The Effects of Light and Heat on the Rubber Content and Impact Strength of Acrylonitrile-Butadiene-Styrene, Polym. Eng. Sci., 1980, 20(15), p 995–1001CrossRef

15.

B.E. Tiganis, L.S. Burn, P. Davis, and A.J. Hill, Thermal Degradation of Acrylonitrile-Butadiene-Styrene (ABS) Blends, J. Polym. Degrad. Stab., 2002, 76(3), p 425–434CrossRef

16.

P. Davis, B.E. Tiganis, and L.S. Burn, The Effect of Photo-oxidative Degradation on Fracture in ABS Pipe Resins, J. Polym. Degrad. Stab., 2004, 84(2), p 233–242CrossRef

17.

R. Scaffaro, L. Botta, and G.D. Benedetto, Physical Properties of Virgin-Recycled ABS Blends: Effect of Post-consumer Content and of Reprocessing Cycles, Eur. Polym. J., 2012, 48(3), p 637–648CrossRef

18.

Z.Q. Liu, A.M. Cunha, X.S. Yi, and A.C. Bernardo, Key Properties to Understand the Performance of Polycarbonate Reprocessed by Injection Molding, J. Appl. Polym. Sci., 2000, 77(6), p 1393–1400CrossRef

19.

J.M. Perez, J.L. Vilas, J.M. Laza, S. Arnaiz, F. Mijangos, E. Bilbao, M. Rodriguez, and L.M. Leon, Effect of Reprocessing and Accelerated Ageing on Thermal and Mechanical Polycarbonate Properties, J. Mater. Process. Technol., 2010, 210(5), p 727–733CrossRef

20.

F. Soriano, G. Morales, and R.D. Leon, Recycling of High Impact Polystyrene in Coextruded Sheet: Influence of the Number of Processing Cycles on the Microstructure and Macroscopic Properties, Polym. Eng. Sci., 2006, 46(12), p 1698–1705CrossRef

21.

A. Boldizar and K. Moller, Degradation of ABS During Repeated Processing and Accelerated Ageing, J. Polym. Degrad. Stab., 2003, 81(2), p 359–366CrossRef

22.

X. Bai, D.H. Isaac, and K. Smith, Reprocessing Acrylonitrile-Butadiene-Styrene Plastics: Structure-Property Relationships, Polym. Eng. Sci., 2007, 47(2), p 120–130CrossRef

23.

Z.Y. Tan, X.F. Xu, S.L. Sun, C. Zhou, Y.H. Ao, H.X. Zhang, and Y. Han, Influence of Rubber Content in ABS in Wide Range on the Mechanical Properties and Morphology of PC/ABS Blends with Different Composition, Polym. Eng. Sci., 2006, 46(10), p 1476–1484CrossRef

24.

M.M. Pan, B. Yin, W. Yang, Y. Zhao, and M.B. Yang, Rheological Properties, Morphology, and Thermal Performance of E-MA-GMA/PC Blend, J. Macromol. Sci. Part B: Phys., 2007, 46(6), p 1267–1278CrossRef

25.

H. Blom, R. Yeh, R. Wojnarowski, and M. Ling, Detection of Degradation of ABS Materials via DSC, Thermochim. Acta, 2006, 442(1-2), p 64–66CrossRef

26.

G. Scott and M. Tahan, Comparison of the Photo-oxidative Behaviour of Some Polybutadiene-Based Polyblends, Eur. Polym. J., 1977, 13(12), p 981–987CrossRef

27.

M. Piton and A. Rivaton, Photo-oxidation of ABS (A > 300 at Long Wavelengths nW, J. Polym. Degrad. Stab., 1997, 55(2), p 147–157CrossRef

28.

S. Bastida, C. Marieta, J.I. Eguiazabal, and J. Nazabal, Effects of Reprocessing on the Nature and Properties of SAN, Eur. Polym. J., 1995, 31(7), p 643–646CrossRef

29.

B. Swoboda, S. Buonomo, E. Leroy, and J.M. Lopez Cuesta, Reaction to Fire of Recycled Poly(ethylene terephthalate)/polycarbonate Blends, J. Polym. Degrad. Stab., 2007, 92(12), p 2247–2256CrossRef

Titel: Effect of Reprocessing and Accelerated Weathering on Impact-Modified Recycled Blend
verfasst von: V. Ramesh
Smita Mohanty
Manoranjan Biswal
Sanjay K. Nayak
Publikationsdatum: 01.12.2015
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 12/2015
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-015-1743-3

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 12/2015

An Investigation into Hot Deformation Characteristics and Processing Maps of High-Strength Armor Steel

Dislocation Configurations and Stress Distribution Along the Transverse Axis of Turbine Blade Body

Microstructure and Tensile Properties of Mg (AM60)/Al2O3 Metal Matrix Composites with Varying Volume Fractions of Fiber Reinforcement

Effect of Viscosity Measurement Method to Simulate High Pressure Die Casting of Thin-Wall AlSi10MnMg Alloy Castings

Studies on Adsorption and Corrosion Inhibitive Properties of Indoline Compounds on N80 Steel in Hydrochloric Acid

Precision Measurement and Modeling of Quenching-Tempering Distortion in Low-Alloy Steel Components with Internal Threads

Premium Partner

Marktübersichten