nach oben

Metals and Materials International

Erschienen in:

22.05.2020

Effect of Sintering Temperature on the Physico-Mechanical Behavior of SiC Reinforced Zinc-Magnesium Based Composite

verfasst von: Amrendra Rai, Pooja Rai, Vijay Kumar, Naresh Kumar Singh, Vinay Kumar Singh

Erschienen in: Metals and Materials International | Ausgabe 9/2021

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The present research work deals with study the effect of sintering temperature on the physical and mechanical behavior of Zn₂Mg₆SiC composite, which can be used as a biodegradable implant. Sintering of the composite has been done at a temperature of 430 °C, 450 °C, 470 °C and 490 °C. The mechanical and physical properties of the samples have been observed to vary with sintering temperature. The grain size of the samples has observed to be optimized at 450 °C with grain size 0.2587 µm and provides maximum strength to the samples. The densification of the composites achieved was found to be maximum at 450 °C having a value 90.30%. Wear rate, hardness, Young’s Modulus of elasticity and flexural strength were observed to be maximum at this temperature. Scanning electron microscopy and X-ray diffraction spectroscopy of the samples at various temperatures were done to find microstructural changes and surface morphology of the composite.

Graphic Abstract

Vorheriger Artikel Effect of Mg Content on the Damping Behavior of Al–Mg Alloys

Nächster Artikel Optimization of Shot Peening Effective Parameters on Surface Hardness Improvement

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

M.B. Kannan, C. Moore, S. Saptarshi, S. Somasundaram, M. Rahuma, A.L. Lopata, Biocompatibility and biodegradation studies of a commercial zinc alloy for temporary mini-implant applications. Sci. Rep. 7, 1–11 (2017). https://doi.org/10.1038/s41598-017-15873-wCrossRef

D. Vojtěch, J. Kubásek, J. Šerák, P. Novák, Mechanical and corrosion properties of newly developed biodegradable Zn-based alloys for bone fixation. Acta Biomater. 7, 3515–3522 (2011). https://doi.org/10.1016/j.actbio.2011.05.008CrossRef

J. Kubásek, D. Vojtěch, Zn-based alloys as alternative biodegradable materials, in Proceedings 21st International Conference on Metallurgy and Materials, Metal Conference (2012)

P.K. Bowen, J. Drelich, J. Goldman, Zinc exhibits ideal physiological corrosion behavior for bioabsorbable stents. Adv. Mater. 25, 2577–2582 (2013). https://doi.org/10.1002/adma.201300226CrossRef

N.S. Murni, M.S. Dambatta, S.K. Yeap, G.R.A. Froemming, H. Hermawan, Cytotoxicity evaluation of biodegradable Zn–3 Mg alloy toward normal human osteoblast cells. Mater. Sci. Eng., C 49, 560–566 (2015). https://doi.org/10.1016/j.msec.2015.01.056CrossRef

M. Hambidge, Zinc and health: current status and future directions. J. Nutr. 130, 1344S–1349S (2000)CrossRef

T.M. Bray, W.J. Bettger, The physiological role of zinc as an antioxidant. Free Radic. Biol. Med. 8, 281–291 (1990). https://doi.org/10.1016/0891-5849(90)90076-UCrossRef

Z.G. Huan, M.A. Leeflang, J. Zhou, L.E. Fratila-Apachitei, J. Duszczyk, In vitro degradation behavior and cyto compatibility of Mg–Zn–Zr alloys. J. Mater. Sci. Mater. Med. 21, 2623–2635 (2010). https://doi.org/10.1007/s10856-010-4111-8CrossRef

J. Nriagu, Zinc deficiency in human health BT. Encycl. Environ. Health (2011). https://doi.org/10.1016/B978-0-444-52272-6.00674-7CrossRef

10.

L.M. Plum, L. Rink, H. Hajo, The essential toxin: impact of zinc on human health. Int. J. Environ. Res. Public Health 7, 1342–1365 (2010). https://doi.org/10.3390/ijerph7041342CrossRef

11.

G.J. Fosmire, Zinc toxicity. Am. J. Clin. Nutr. 51, 225–227 (1990)CrossRef

12.

A.S. Prasad, Zinc: an antioxidant and anti-inflammatory agent: role of zinc in degenerative disorders of aging. J. Trace Elem. Med Biol. 28, 364–371 (2014). https://doi.org/10.1016/j.jtemb.2014.07.019CrossRef

13.

F. Witte, N. Hort, C. Vogt, S. Cohen, K.U. Kainer, R. Willumeit, F. Feyerabend, Degradable biomaterials based on magnesium corrosion. Curr. Opin. Solid State Mater. Sci. 12, 63–72 (2008). https://doi.org/10.1016/j.cossms.2009.04.001CrossRef

14.

S. Zhang, X. Zhang, C. Zhao, J. Li, Y. Song, C. Xie, H. Tao, Y. Zhang, Y. He, Y. Jiang, Y. Bian, Research on an Mg–Zn alloy as a degradable biomaterial. Acta Biomater. 6, 626–640 (2010). https://doi.org/10.1016/j.actbio.2009.06.028CrossRef

15.

B.K. Prasad, S. Das, O.P. Modi, A.K. Jha, R. Dasgupta, A.H. Yegneswaran, Wear response of a Zn-base alloy in the presence of SiC particle reinforcement: a comparative study with a copper-base alloy. J. Mater. Eng. Perform. 8, 693–700 (1999). https://doi.org/10.1361/105994999770346468CrossRef

16.

N. Saheb, Z. Iqbal, A. Khalil, A.S. Hakeem, N. Al Aqeeli, T. Laoui, A. Al-Qutub, R. Kirchner, Spark plasma sintering of metals and metal matrix nanocomposites: a review. J. Nanomater. 18, 1–13 (2012). https://doi.org/10.1155/2012/983470CrossRef

17.

A. Gökçe, F. Findik, Mechanical and physical properties of sintered aluminum powders. J. Achiev. Mater. Manuf. Eng. 30, 157–164 (2008)

18.

K. Yamaguchi, N. Takakura, S. Imatami, Compaction and sintering characteristics of composite metal powders. J. Mater. Process. Technol. 63, 364–369 (1997)CrossRef

19.

J.W. Kaczmar, K. Pietrzak, W. Wlosiński, Production and application of metal matrix composite materials. J. Mater. Process. Technol. 106, 58–67 (2000). https://doi.org/10.1016/S0924-0136(00)00639-7CrossRef

20.

C.P. Ling, M.B. Bush, D.S. Perera, The effect of fabrication techniques on the properties of A1–SiC composites. J. Mater. Process. Technol. 48, 325–331 (1995)CrossRef

21.

C.R.K. Mohan, P.K. Bajpai, Effect of sintering optimization on the electrical properties of bulk axSr₁xTiO₃ ceramics. Phys. B 403, 2173–2188 (2008)CrossRef

22.

L. Hallmann, P. Ulmer, E. Reusser et al., Effect of dopants and sintering temperature on microstructure and low temperature degradation of dental Y-TZP-zirconia. J. Eur. Ceram. Soc. 32, 4091–4104 (2012)CrossRef

23.

N.J. Shaw, Densification and coarsening during solid state sintering of ceramics: a review of the models III. Coarsening. Int. J Powder Metall. 21, 25–29 (1989)

24.

D.E. Garcia, A.N. Klein, D. Hotza, Advanced ceramics with dense and fine-grained microstructures through fast firing. Rev. Adv. Mater. Sci. 30, 273–281 (2012)

25.

Q. Wang, Q. Wang, X. Zhang et al., The effect of sintering temperature on the structure and degradability of strontium-doped calcium polyphosphate bioceramic. Ceram. Silik. 54, 97–102 (2010)

26.

K. Krishnan, S.S. Sahay, S. Singh et al., Modeling the accelerated cyclic annealing kinetics. J. Appl. Phys. 100, 093505 (2006)CrossRef

27.

R. Bjørk, V. Tikare, H.L. Frandsen, N. Pryds, The effect of particle size distributions on the microstructural evolution during sintering. J. Am. Ceram. Soc. 96, 103–110 (2013). https://doi.org/10.1111/jace.12100CrossRef

28.

T. Hungría, J. Galy, A. Castro, Spark plasma sintering as a useful technique to the nanostructuration of piezo-ferroelectric materials. Adv. Eng. Mater. 11, 615–631 (2009)CrossRef

29.

S. Ahn, S.J. Park, S. Lee, S.V. Atre, R.M. German, Effect of powders and binders on material properties and molding parameters in iron and stainless steel powder injection molding process. Powder Technol. 193, 162–169 (2009). https://doi.org/10.1016/j.powtec.2009.03.010CrossRef

30.

Z.Y. Liu, N.H. Loh, S.B. Tor, K.A. Khor, Characterization of powder injection molding feedstock. Mater. Charact. 49, 313–320 (2002). https://doi.org/10.1016/S1044-803(02)00282-6CrossRef

31.

G. Shibo, Q. Xuanhui, H. Xinbo, Z. Ting, D. Bohua, Powder injection molding of Ti–6Al–4 V alloy. J. Mater. Process. Technol. 173, 310–314 (2006). https://doi.org/10.1016/j.jmatprotec.2005.12.001CrossRef

32.

A. Nouri, C. Wen, Surfactants in mechanical alloying/milling: a catch-22 situation. Crit. Rev. Solid State Mater. Sci. 39, 81–108 (2014)CrossRef

33.

H. H. Rieke, G. V. Chilingarian, Chapter 2 Interrelationships among density, porosity, remaining moisture content, pressure and depth. Dev. Sedimentol. 16, 31–86 (1974). https://doi.org/10.1016/S0070-4571(08)70772-6CrossRef

34.

S.C. Sharma, Equation for the density of particle-reinforced metal matrix composites: a new approach. J. Mater. Eng. Perform. 12, 324–330 (2003)CrossRef

35.

H. Naceur, A. Megriche, M. El Maaoui, Effect of sintering temperature on microstructure and electrical properties of Sr1 x(Na_0.5Bi_0.5)xBi₂Nb₂O₉ solid solutions. J. Adv. Ceram. 3, 17–30 (2014). https://doi.org/10.1007/s40145-014-0089-xCrossRef

36.

J.C. Wurst, J.A. Nelson, Lineal intercept technique for measuring grain size in two-phase polycrystalline ceramics. J. Am. Ceram. Soc. 55, 109–111 (1972)CrossRef

37.

ASTM C1674-11 Standard Test Method For Flexural Strength Of Advanced Ceramics With Engineered Porosity (Honeycomb Cellular Channels) At Ambient Temperatures. 2016.

38.

ASTM E3484-99 A. Standard Test Method for Micro Indentation Hardness Of Materials. 1984

39.

E. Reufi, I. Thomas, Evaluation of modulus of elasticity by non-destructive method of hybrid fiber reinforced concrete. Int. J. Adv. Chem. Eng. Biol. Sci. 3, 1–4 (2016). https://doi.org/10.15242/ijacebs.c0416019CrossRef

40.

I.V. Kraghelsky, Calculation of wear rate. J. Basic Eng. 87, 785 (1965). https://doi.org/10.1115/1.3650690CrossRef

41.

S.E. Shirsath, R.H. Kadam, A.S. Gaikwad et al., Effect of sintering temperature and the particle size on the structural and magnetic properties of nano crystalline Li_0.5Fe_2.5O₄. J. Magn. Mater. 323, 3104–3108 (2011)CrossRef

42.

Y. Boonyongmaneerat, Mechanical properties of partially sintered materials. Mater. Sci. Eng., A 452, 773–780 (2007)CrossRef

43.

J.A. Floro, C.V. Thompson, R. Carel et al., Competition between strain and interface energy during epitaxial grain growth in Ag films on Ni (001). J. Mater. Res. 9, 2411–2424 (1994)CrossRef

44.

J. Cortés, E. Valencia, Phenomenological equations of the kinetics of heterogeneous adsorption with interaction between adsorbed molecules. Phys. Rev. B. 51, 2621–2623 (1995)CrossRef

45.

D.W. Budworth, The selection of grain-growth control additives for the sintering of ceramic. Miner. Mag. 37, 833–838 (1970)CrossRef

46.

D.J. Veljovic, B. Jokic, R. Petrovic, E. Palcevskis, A. Dindune, I.N. Mihailescu, D.J. Janaćković, Processing of dense nanostructured HA ceramics by sintering and hot pressing. Ceram. Int. 35, 1407–1413 (2009)CrossRef

47.

C.H. Ji, N.H. Loh, K.A. Khor, S.B. Tor, Sintering study of 316L stainless steel metal injection molding parts using Taguchi method: final density. Mater. Sci. Eng., A 311, 74–82 (2001). https://doi.org/10.1016/S0921-5093(01)00942-XCrossRef

48.

M.R. Ghomashchi, A. Vikhrov, Squeeze casting: an overview. J. Mater. Process. Technol. 101, 1–9 (2000)CrossRef

49.

T. Kehoe, J. Bryner, V. Reboud, J. Dual, C.M. Sotomayor Torres, Nano-scale effects on Young’s modulus of nano imprint polymers measured by photoacoustic metrology. J. Phys: Conf. Ser. 214, 11–16 (2010). https://doi.org/10.1088/1742-6596/214/1/012049CrossRef

50.

J. Rho, R. Ashman, C. Turner, Young’s modulus of trabecular and cortical bone material. J. Biomech. 26, 111–119 (1993). https://doi.org/10.1016/0021-9290(93)90042-DCrossRef

Titel: Effect of Sintering Temperature on the Physico-Mechanical Behavior of SiC Reinforced Zinc-Magnesium Based Composite
verfasst von: Amrendra Rai
Pooja Rai
Vijay Kumar
Naresh Kumar Singh
Vinay Kumar Singh
Publikationsdatum: 22.05.2020
Verlag: The Korean Institute of Metals and Materials
Erschienen in: Metals and Materials International / Ausgabe 9/2021
Print ISSN: 1598-9623
Elektronische ISSN: 2005-4149
DOI: https://doi.org/10.1007/s12540-020-00748-z

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Graphic Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 9/2021

Ratcheting Fatigue Behaviour of Zircaloy-2 at 300 °C

Microstructure Evolution and Dynamic Precipitation Behavior of Mg–10Gd–4Y–1Sm–0.5Zr Alloy During Backward Hot Extrusion

Optimization of Shot Peening Effective Parameters on Surface Hardness Improvement

Surface Metallization and Ceramic Deposition on Thermoplastic-Polymer and Thermosetting-Polymer Composite Via Atmospheric Plasma Spraying

Tensile and Corrosion Properties of Anodized Ultrafine-Grained Ti–13Nb–13Zr Biomedical Alloy Obtained by High-Pressure Torsion

Significance of Finite Element Models and Solid-State Phase Transformation on the Evaluation of Weld Induced Residual Stresses

Premium Partner

Marktübersichten