Top

Advances in Manufacturing

Published in:

01-12-2015

Analysis of hard turning process: thermal aspects

Authors: Varaprasad Bhemuni, Srinivasa Rao Chalamalasetti, Pavan Kumar Konchada, Venkata Vinay Pragada

Published in: Advances in Manufacturing | Issue 4/2015

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In manufacturing sector, hard turning has emerged as a vital machining process for cutting hardened steels. Besides many advantages of hard turning operations, one has to implement to achieve close tolerances in terms of surface finish, high product quality, reduced machining time, low operating cost and environmental friendly characteristics. In the study, three dimensional (3D) computer aided engineering (CAE) based simulation of hard turning by using commercial software DEFORM 3D has been compared to the experimental results of stresses, temperatures and tool forces in machining of AISI D3 and AISI H13 steel using mixed ceramic inserts (CC6050). In the following analysis, orthogonal cutting models are proposed, considering several processing parameters such as cutting speed, feed and depth of cut. An exhaustive friction modelling at the tool-work interface is carried out. Work material flow around the cutting edge is carefully modelled with adaptive re-meshing simulation capability of DEFORM 3D. The process simulations are performed at constant feed rate (0.075 mm/r) and cutting speed (155 m/min), and analysis is focused on stresses, forces and temperatures generated during the process of machining. Close agreement is observed between the CAE simulation and experimental values.

previous article Finite element analysis of chip formation and residual stresses induced by sequential cutting in side milling with microns to sub-micron uncut chip thickness and finite cutting edge radius

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Byrne G, Dornfeld D, Denkena B (2003) Advanced cutting technology. Ann CIRP 52(2):483–507CrossRef

Klocke F, Brinksmeier E, Weinert K (2005) Capability profile of hard cutting and grinding processes. Ann CIRP 54(2):557–580CrossRef

Klocke F, Kratz H (2005) Advanced tool edge geometry for high precision hard turning. Ann CIRP 54(1):47–50CrossRef

Denkena B, Becker JC, de Leon-Garcia L (2005) Study of the influence of the cutting edge micro geometry on the cutting forces and wear behavior in turning operations. In: Proceedings of the 8th CIRP, international workshop on modelling of machining operations, Chemnitz, pp 503–507

Özel T, Hsu TK, Zeren E (2005) Effects of cutting edge geometry, workpiece hardness, feed rate and cutting speed on surface roughness and forces in finish turning of hardened AISI H13 steel. Int J Adv Manuf Technol 25:262–269CrossRef

Zou B, Chen M, Li S (2011) Study on finish-turning of NiCr20TiAl nickel-based alloy using Al₂O₃/TiN-coated carbide tools. Int J Adv Manuf Technol 53:81–92CrossRef

Fahad M, Mativenga PT, Sheikh MA (2012) A comparative study of multilayer and functionally graded coated tools in high-speed machining. Int J Adv Manuf Technol 62:43–57CrossRef

Gopalsamy BM, Mondal B, Ghosh S (2009) Optimisation of machining parameters for hard machining: grey relational theory approach and ANOVA. Int J Adv Manuf Technol 45:1068–1086CrossRef

Ahilan C, Kumanan S, Sivakumaran N (2010) Application of grey based taguchi method in multi response optimization of turning process. Adv Prod Eng Manag 5(3):171–180

10.

Tzeng CJ, Lin YH, Yang YK et al (2009) Optimization of turning operations with multiple performance characteristics using the taguchi method and grey relational analysis. J Mater Process Technol 209:2753–2759CrossRef

11.

Kazancoglu Y, Esme U, Bayramoglu M et al (2011) Multi-objective optimization of the cutting forces in turning operations using the grey-based taguchi method. Mater Technol 45(2):105–110

12.

Senthilkumar N, Tamizharasan T, Anandakrishnan V (2013) An ANN approach for predicting the cutting inserts performances of different geometries in hard turning. Adv Prod Eng Manag 8(4):231–241

13.

Özel T (2003) Modeling of hard part machining: effect of insert edge preparation for CBN cutting tools. J Mater Process Technol 141:284–293CrossRef

14.

Yen YC, Jain A, Altan T (2004) A finite element analysis of orthogonal machining using different tool edge geometry. J Mater Process Technol 146:72–81CrossRef

15.

Hua J, Shivpuri R, Cheng X et al (2005) Effect of feed rate, workpiece hardness and cutting edge on subsurface residual stress in hard turning of bearing steel using chamfer and hone edge geometry. Mater Sci Eng, A 394:238–248CrossRef

16.

Chen L, ElWardany TI, Nasr M et al (2006) Effects of edge preparation and feed when hard turning a hotwork die steel with polycrystalline cubic boron nitride tools. Ann CIRP 55(1):88–92CrossRef

17.

Umbrello D, Rizzuti S, Outeiro JC (2008) Hardnessbased flowstress for numerical simulation of hardmachining AISI H13 tool steel. J Mater Process Technol 199(1–3):64–73CrossRef

18.

Karpat Y, Özel T (2008) Mechanics of high speed machining with curvilinear tools. Int J Mach Tools Manuf 49:195–208CrossRef

19.

Ceretti E, Lazzaroni C, Menegardo L et al (2000) Turning simulations using a three-dimensional FEM code. J Mater Process Technol 98:99–103CrossRef

20.

Guo Y, Liu CR (2002) 3D FEA modeling of hard turning. ASME J Manuf Sci Eng 124:189–199CrossRef

21.

Aurich JC, Bil H (2006) 3D finite element modelling of segmented chip formation. Ann CIRP 55(1):47–50CrossRef

22.

Rosochowska M, Balendra R, Chodnikiewicz K (2003) Measurements of thermal conductance. J Mater Process Technol 135:204–210CrossRef

23.

Incropera FP, DeWitt DP (2001) Fundamentals of heat and mass transfer. Willey, New York

24.

Johnson GR, Cook WH (1985) Fracture characteristic of three metals subjected to various strains. Eng Fract Mech 21:3CrossRef

Title: Analysis of hard turning process: thermal aspects
Authors: Varaprasad Bhemuni
Srinivasa Rao Chalamalasetti
Pavan Kumar Konchada
Venkata Vinay Pragada
Publication date: 01-12-2015
Publisher: Shanghai University
Published in: Advances in Manufacturing / Issue 4/2015
Print ISSN: 2095-3127
Electronic ISSN: 2195-3597
DOI: https://doi.org/10.1007/s40436-015-0124-3

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 4/2015

Single point and asymmetric incremental forming

Experimental investigation of tool wear and chip formation in cryogenic machining of titanium alloys

Finite element analysis of chip formation and residual stresses induced by sequential cutting in side milling with microns to sub-micron uncut chip thickness and finite cutting edge radius

Dual phase titanium alloy hot forging process design: experiments and numerical modeling

Micro ball-end milling of freeform titanium parts

An experimental study on grinding of Zr-based bulk metallic glass

Premium Partners