Top

Published in:

2018 | OriginalPaper | Chapter

9. Cold-Sprayed Metal Matrix Composite Coatings

Authors : Yik Tung Roy Lee, Tanvir Hussain, Gary A. Fisher, André G. McDonald

Published in: Cold-Spray Coatings

Publisher: Springer International Publishing

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Metal matrix composites (MMCs) combine high-hardness materials, such as ceramics, with ductile metal matrices. The resulting MMC material often has excellent strength and toughness due to the addition of hard reinforcing particles in the matrix. Typically, MMCs can be created by sintering, hot pressing, extrusion, pressure infiltration, reaction processing, or thermal spraying. However, most of these techniques are expensive and require high temperatures. Cold spraying is an innovative and cost-effective technique to manufacture of MMCs. Cold spraying relies on the plastic deformation of particles upon impact to fabricate coatings. Hard-facing particles used in MMCs typically do not plastically deform and can fracture upon high-velocity impact. It has been found that ceramic particle velocity, size, and morphology may have a significant influence on ceramic deposition efficiency. Cold spraying mechanically blended metal-ceramic powders can result in MMC ceramic content of approximately 30 vol.%, while cold spraying with composite powders can achieve ceramic content up to 52 vol.%. In addition, due to the high-velocity impact of the particles in cold spraying, ceramic powders in the feedstock provide additional enhancements to the properties of the deposited MMCs. It has been found that the addition of ceramic particles improves the deposition efficiency of the blended powders, increases pull-off bond strength, and increases the bonding within the coating. This chapter will highlight the research that has been conducted to improve the deposition efficiency of the ceramic particles and their impact on the cold-sprayed MMC material system.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

previous chapter Characterization, Deposition Mechanisms, and Modeling of Metallic Glass Powders for Cold Spray

next chapter Metal Matrix Composite Coatings by Cold Spray

Al-Mutairi S, Hashmi MSJ, Yilbas BS, Stokes J (2015) Microstructural characterization of HVOF/plasma thermal spray of micro/nano WC–12%co powders. Surf Coat Technol 264:175–186. https://doi.org/10.1016/j.surfcoat.2014.12.050 CrossRef

Ang ASM, Berndt CC, Cheang P (2011) Deposition effects of WC particle size on cold sprayed WC–Co coatings. Surf Coat Technol 205:3260–3267. https://doi.org/10.1016/j.surfcoat.2010.11.045 CrossRef

Assadi H, Gärtner F, Stoltenhoff T, Kreye H (2003) Bonding mechanism in cold gas spraying. Acta Mater 51:4379–4394. https://doi.org/10.1016/S1359-6454(03)00274-X CrossRef

ASTM International (2013) ASTM C633–13, standard test method for adhesion or cohesion strength of thermal spray coatings. ASTM International, West Conshohocken

Balasubramanian M (2013) Composite materials and processing. Taylor & Francis, Boca Raton, FloridaCrossRef

Chawla N, Chawla KK (2013) Metal matrix composites. Springer New York, New YorkCrossRef

Chen H, Hutchings I (1998) Abrasive wear resistance of plasma-sprayed tungsten carbide–cobalt coatings. Surf Coat Technol 107:106–114. https://doi.org/10.1016/S0257-8972(98)00581-7 CrossRef

Fauchais PL, Heberlein JVR, Boulos MI (2014) Thermal spray fundamentals. Springer US, BostonCrossRef

Feng C, Guipont V, Jeandin M et al (2012) B₄C/Ni composite coatings prepared by cold spray of blended or CVD-coated powders. J Therm Spray Technol 21:561–570. https://doi.org/10.1007/s11666-012-9774-x CrossRef

Gao P-H, Li Y-G, Li C-J et al (2008) Influence of powder porous structure on the deposition behavior of cold-sprayed WC-12Co coatings. J Therm Spray Technol 17:742–749. https://doi.org/10.1007/s11666-008-9258-1 CrossRef

Getu H, Spelt JK, Papini M (2012) Conditions leading to the embedding of angular and spherical particles during the solid particle erosion of polymers. Wear 292–293:159–168. https://doi.org/10.1016/j.wear.2012.05.017 CrossRef

Guilemany JM, de Paco JM, Miguel JR, Nutting J (1999) Characterization of the W₂C phase formed during the high velocity oxygen fuel spraying of a WC + 12 pct Co powder. Metall Mater Trans A 30:1913–1921. https://doi.org/10.1007/s11661-999-0002-3 CrossRef

Hodder KJ, Izadi H, McDonald AG, Gerlich AP (2012) Fabrication of aluminum–alumina metal matrix composites via cold gas dynamic spraying at low pressure followed by friction stir processing. Mater Sci Eng A 556:114–121. https://doi.org/10.1016/j.msea.2012.06.066 CrossRef

Ibrahim IA, Mohamed FA, Lavernia EJ (1991) Particulate reinforced metal matrix composites – a review. J Mater Sci 26:1137–1156. https://doi.org/10.1007/BF00544448 CrossRef

Irissou E, Legoux J-G, Arsenault B, Moreau C (2007) Investigation of Al-Al₂O₃ cold spray coating formation and properties. J Therm Spray Technol 16:661–668. https://doi.org/10.1007/s11666-007-9086-8 CrossRef

Kar KK (ed) (2016) Composite materials: processing, applications, characterizations, 1st edn. Springer, New York

Kim H-J, Lee C-H, Hwang S-Y (2005) Fabrication of WC–Co coatings by cold spray deposition. Surf Coat Technol 191:335–340. https://doi.org/10.1016/j.surfcoat.2004.04.058 CrossRef

Kim HS (2000) On the rule of mixtures for the hardness of particle reinforced composites. Mater Sci Eng A 289:30–33. https://doi.org/10.1016/S0921-5093(00)00909-6 CrossRef

Lee HY, Jung SH, Lee SY et al (2005) Correlation between Al₂O₃ particles and interface of Al–Al₂O₃ coatings by cold spray. Appl Surf Sci 252:1891–1898. https://doi.org/10.1016/j.apsusc.2005.03.148 CrossRef

Maev RG, Leshchynsky V (eds) (2016) Cold gas dynamic spray. CRC Press/Taylor & Francis Group, Boca Raton

Melendez NM, McDonald AG (2013) Development of WC-based metal matrix composite coatings using low-pressure cold gas dynamic spraying. Surf Coat Technol 214:101–109. https://doi.org/10.1016/j.surfcoat.2012.11.010 CrossRef

Melendez NM, Narulkar VV, Fisher GA, McDonald AG (2013) Effect of reinforcing particles on the wear rate of low-pressure cold-sprayed WC-based MMC coatings. Wear 306:185–195. https://doi.org/10.1016/j.wear.2013.08.006 CrossRef

Moridi A, Hassani-Gangaraj SM, Guagliano M, Dao M (2014) Cold spray coating: review of material systems and future perspectives. Surf Eng 30:369–395. https://doi.org/10.1179/1743294414Y.0000000270 CrossRef

Na H, Bae G, Shin S et al (2009) Advanced deposition characteristics of kinetic sprayed bronze/diamond composite by tailoring feedstock properties. Compos Sci Technol 69:463–468. https://doi.org/10.1016/j.compscitech.2008.11.015 CrossRef

Papyrin A (2007) Cold spray technology. Elsevier, Amsterdam/London

Leger P-E, Borit F, Fabregue N, Jeandin M (2016) Influence of powder characteristics on the microstructure and bond strength of cold-sprayed aluminum coating. ASM International, Shanghai

Qi X, Eigen N, Aust E et al (2006) Two-body abrasive wear of nano- and microcrystalline TiC–Ni-based thermal spray coatings. Surf Coat Technol 200:5037–5047. https://doi.org/10.1016/j.surfcoat.2005.05.007 CrossRef

Schmidt T, Assadi H, Gärtner F et al (2009) From particle acceleration to impact and bonding in cold spraying. J Therm Spray Technol 18:794–808. https://doi.org/10.1007/s11666-009-9357-7 CrossRef

Schmidt T, Gärtner F, Assadi H, Kreye H (2006) Development of a generalized parameter window for cold spray deposition. Acta Mater 54:729–742. https://doi.org/10.1016/j.actamat.2005.10.005 CrossRef

Shkodkin A, Kashirin A, Klyuev O, Buzdygar T (2006) Metal particle deposition stimulation by surface abrasive treatment in gas dynamic spraying. J Therm Spray Technol 15:382–386. https://doi.org/10.1361/105996306X124383 CrossRef

Shockley JM, Descartes S, Vo P et al (2015) The influence of Al2O3 particle morphology on the coating formation and dry sliding wear behavior of cold sprayed Al–Al2O3 composites. Surf Coat Technol 270:324–333. https://doi.org/10.1016/j.surfcoat.2015.01.057 CrossRef

Sova A, Kosarev VF, Papyrin A, Smurov I (2011) Effect of ceramic particle velocity on cold spray deposition of metal-ceramic coatings. J Therm Spray Technol 20:285–291. https://doi.org/10.1007/s11666-010-9571-3 CrossRef

Sova A, Papyrin A, Smurov I (2009) Influence of ceramic powder size on process of cermet coating formation by cold spray. J Therm Spray Technol 18:633–641. https://doi.org/10.1007/s11666-009-9359-5 CrossRef

Spencer K, Fabijanic DM, Zhang M-X (2009) The use of Al–Al₂O₃ cold spray coatings to improve the surface properties of magnesium alloys. Surf Coat Technol 204:336–344. https://doi.org/10.1016/j.surfcoat.2009.07.032 CrossRef

Spencer K, Fabijanic DM, Zhang M-X (2012) The influence of Al₂O₃ reinforcement on the properties of stainless steel cold spray coatings. Surf Coat Technol 206:3275–3282. https://doi.org/10.1016/j.surfcoat.2012.01.031 CrossRef

Stewart DA, Shipway PH, McCartney DG (1999) Abrasive wear behaviour of conventional and nanocomposite HVOF-sprayed WC–Co coatings. Wear 225–229:789–798. https://doi.org/10.1016/S0043-1648(99)00032-0 CrossRef

Wang J, Villafuerte J (2009) Low pressure cold spray of tungsten carbide composite coatings. Adv Mater Process 167:54–56

Title: Cold-Sprayed Metal Matrix Composite Coatings
Authors: Yik Tung Roy Lee
Tanvir Hussain
Gary A. Fisher
André G. McDonald
Publisher: Springer International Publishing
Book: Cold-Spray Coatings
Print ISBN: 978-3-319-67182-6

Electronic ISBN: 978-3-319-67183-3

Copyright Year: 2018
DOI: https://doi.org/10.1007/978-3-319-67183-3_9

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Premium Partners