Top

Journal of Materials Engineering and Performance

Published in:

03-01-2019

Creep Behavior of Commercially Pure Titanium TA2 After Supersonic Fine Particles Bombardment

Authors: Liling Ge, Zhanwei Yuan, Zhenhua Han

Published in: Journal of Materials Engineering and Performance | Issue 2/2019

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In this study, the effect of supersonic fine particles bombardment (SFPB) on the creep behavior of commercially pure titanium TA2 was investigated. Microstructural observations with x-ray diffraction and a transmission electron microscope indicated that the grain size of the TA2 surface layer was refined to nanometer scale in the topmost surface layer after SFPB treatment. Indentation creep tests showed that the SFPB-treated sample had a lower maximum depth and higher hardness than the original sample at the same load, indicating an enhancement of the surface strength with SFPB. With lower creep displacements, the creep resistance was also improved after SFPB treatment. The maximum creep rate under different loading conditions showed obvious loading time and load dependencies. The maximum creep rate of the SFPB-treated sample was lower than the original sample for all test conditions, and the maximum creep strain rate of the SFPB-treated sample was similar to that of the original sample. The indentation stress of the SFPB-treated sample was higher than the original sample, while the creep stress exponent of the original sample was slightly higher than for the SFPB-treated sample, with no obvious variation tendency with different loading times or loads.

previous article Enhanced Surface Properties and Microstructure Evolution of Cr12MoV Using Ultrasonic Surface Rolling Process Combined with Deep Cryogenic Treatment

next article Microstructure and Mechanical Properties of Powder Thixoforged Amorphous Ni55Nb35Si10-Reinforced Al Matrix Composites

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

L. Zhu, Y. Guan, Y. Wang, Z. Xie, and J. Lin, Influence of Process Parameters of Ultrasonic Shot Peening on Surface Nanocrystallization and Hardness of Pure Titanium, Int. J. Adv. Manuf. Technol., 2016, 89(5-8), p 1–18CrossRef

S. Dai, Y. Zhu, and Z. Huang, Microstructure and Tensile Behaviour of Pure Titanium Produced After High-Energy Shot Peening, Mater. Sci. Technol., 2016, 32, p 1323–1329CrossRef

O. Unal, A.C. Karaoglanli, R. Varol, and A. Kobayashi, Microstructure Evolution and Mechanical Behavior of Severe Shot Peened Commercially Pure Titanium, Vacuum, 2014, 110, p 202–206CrossRef

Y.G. Liu, M.Q. Li, and H.J. Liu, Nanostructure and Surface Roughness in the Processed Surface Layer of Ti-6Al-4V via Shot Peening, Mater. Charact., 2017, 123, p 83–90CrossRef

B.A. De-Ma, M.A. Shi-Ning, L.I. Chang-Qing, F.J. Meng, and T.Y. Xiong, Surface Nanocrystallization of 45 Steel Induced by Supersonic Fine Particles Bombarding, Mater. Sci. Technol., 2007, 15(3), p 342–346

J. Yang, Y. Zhang, L. Ge, J. Chen, and F. Xing, Surface Strengthening of 2A14 Aluminum Alloy Based on Surface Nanocrystallization, Heat Treat. Metals, 2017, 42(3), p 124–128

L. Kong, Y. Lao, T. Xiong, and T. Li, Nanocrystalline Surface Layer on AISI, 52100 Steel Induced by Supersonic Fine Particles Bombarding, J. Therm. Spray Technol., 2013, 22(6), p 1007–1013CrossRef

L. Ge, N. Tian, Z. Lu, and C. You, Influence of the Surface Nanocrystallization on the Gas Nitriding of Ti-6Al-4V Alloy, Appl. Surf. Sci., 2013, 286(4), p 412–416CrossRef

S. Dai, Y. Zhu, and Z. Huang, Microstructure Evolution and Strengthening Mechanisms of Pure Titanium with Nano-structured Surface Obtained by High Energy Shot Peening, Vacuum, 2016, 125, p 215–221CrossRef

10.

Y.G. Liu, H.M. Li, and M.Q. Li, Characterization of Surface Layer in TC17 Alloy Treated by Air Blast Shot Peening, Mater. Des., 2015, 65(65), p 120–126CrossRef

11.

R.A. Waikar, Y.B. Guo, J.F. Liu, and Z.Y. Liu, Electrochemical Corrosion Behavior of Surface Nanocrystallized Steel and Aluminum Alloys by Air Blast Shot Peening (ABSP), in International Symposium Flexible Automation (2016), p. 359–365

12.

Y. Todaka, M. Umemoto, Y. Watanabe, and K. Tsuchiya, Formation of Nanocrystalline Structure in Steels by Air Blast Shot Peening and Particle Impact Processing, Mater. Sci. Forum, 2004, 449–452, p 1149–1152CrossRef

13.

C. Zhao, P. Cao, W. Ji, P. Han, J. Zhang, F. Zhang, Y. Jiang, and X. Zhang, Hierarchical Titanium Surface Textures Affect Osteoblastic Functions, J. Biomed. Mater. Res. Part A, 2011, 99A(4), p 666–675CrossRef

14.

C. Zhao, W. Ji, P. Han, J. Zhang, Y. Jiang, and X. Zhang, In Vitro and In Vivo Mineralization and Osseointegration of Nanostructured Ti6Al4V, J. Nanopart. Res., 2011, 13(2), p 645–654CrossRef

15.

K. Lu and J. Lu, Surface Nanocrystallization (SNC) of Metallic Materials-Presentation of the Concept Behind a New Approach, J. Mater. Sci. Technol., 1999, 15(3), p 193–197

16.

G. Liu, J. Lu, and K. Lu, Surface Nanocrystallization of 316L Stainless Steel Induced by Ultrasonic Shot Peening, Mater. Sci. Eng. A, 2000, 286(1), p 91–95CrossRef

17.

K.S. Raja, S.A. Namjoshi, and M. Misra, Improved Corrosion Resistance of Ni-22Cr-13Mo-4W Alloy by Surface Nanocrystallization, Mater. Lett., 2005, 59(5), p 570–574CrossRef

18.

X.Y. Mao, D.Y. Li, F. Fang, R.S. Tan, and J.Q. Jiang, Application of a Simple Surface Nanocrystallization Process to a Cu-30Ni Alloy for Enhanced Resistances to Wear and Corrosive Wear, Wear, 2011, 271(9), p 1224–1230CrossRef

19.

B. Zhao, Y.U. Tianyu, W. Ding, and L.I. Xianying, Effects of Pore Structure and Distribution on Strength of Porous Cu-Sn-Ti Alumina Composites, Chin. J. Aeronaut., 2017, 30(6), p 2004–2015CrossRef

20.

X. Xi, W. Ding, Y. Fu, and J. Xu, Grindability Evaluation and Tool Wear During Grinding of Ti 2 AlNb Intermetallics, Int. J. Adv. Manuf. Technol., 2017, 94(9), p 1–10

21.

C. Liu, W. Ding, T. Yu, and C. Yang, Materials Removal Mechanism in High-Speed Grinding of Particulate Reinforced Titanium Matrix Composites, Precis. Eng., 2017, 51, p 68–77CrossRef

22.

Z. Li, W. Ding, C. Liu, and H. Su, Grinding Performance and Surface Integrity of Particulate-Reinforced Titanium Matrix Composites in Creep-Feed Grinding, Int. J. Adv. Manuf. Technol., 2017, 94(2), p 1–12

23.

D.R. Luster, W.W. Wentz, and D.W. Kaufmann, Creep Properties of Titanium, Mater. Methods, 1953, 37, p 100–103

24.

Y. Xiang, W. Zhu, C.J. Liu, F.Z. Xuan, Y.N. Wang, and W.C. Kuang, Creep Degradation Characterization of Titanium Alloy Using Nonlinear Ultrasonic Technique, Ndt & E Int., 2015, 72, p 41–49CrossRef

25.

Z. Liu, J. Shao, S. Xie, and J. Secq, Gas Permeability Evolution of Clayey Rocks in Process of Compressive Creep Test, Mater. Lett., 2015, 139, p 422–425CrossRef

26.

J.D. French, J. Zhao, M.P. Harmer, H.M. Chan, and G.A. Miller, Creep of Duplex Microstructure, J. Am. Ceram. Soc., 2010, 77(11), p 2857–2865CrossRef

27.

A.C.F. Cocks and M.F. Ashby, On Creep Fracture by Void Growth, Prog. Mater. Sci., 1982, 27(3), p 189–244CrossRef

28.

J. Xie, S. Tian, X. Zhou, X. Yu, and W. Wang, Influence of Heat Treatment Regimes on Microstructure and Creep Properties of FGH95 Nickel Base Superalloy, Mater. Sci. Eng. A, 2012, 538(2), p 306–314CrossRef

29.

J. Pešička, R. Kužel, A. Dronhofer, and G. Eggeler, The Evolution of Dislocation Density During Heat Treatment and Creep of Tempered Martensite Ferritic Steels, Acta Mater., 2003, 51(16), p 4847–4862CrossRef

30.

J. Alkorta, On the Elastic Effects in Power-Law Indentation Creep with Sharp Conical Indenters, J. Mater. Res., 2008, 23(1), p 182–188CrossRef

31.

L. Wang, L. Xie, L.C. Zhang, L. Chen, Z. Ding, Y. Lv, W. Zhang, W. Lu, and D. Zhang, Microstructure Evolution and Superelasticity of Layer-Like NiTiNb Porous Metal Prepared by Eutectic Reaction, Acta Mater., 2018, 143, p 214–226CrossRef

32.

S. Ehtemam-Haghighi, G. Cao, and L.-C. Zhang, Nanoindentation Study of Mechanical Properties of Ti Based Alloys with Fe and Ta Additions, J. Alloys Compd., 2017, 692, p 892–897CrossRef

33.

W.C. Oliver and G.M. Pharr, Nanoindentation in Materials Research: Past, Present, and Future, MRS Bull., 2010, 35(11), p 897–907CrossRef

34.

W.C. Oliver and G.M. Pharr, An Improved Technique for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments, J. Mater. Res., 1992, 7(6), p 1564–1583CrossRef

35.

L. Wang, L. Xie, Y. Lv, L.C. Zhang, L. Chen, Q. Meng, J. Qu, D. Zhang, and W. Lu, Microstructure Evolution and Superelastic Behavior in Ti-35Nb-2Ta-3Zr Alloy Processed by Friction Stir Processing, Acta Mater., 2017, 131, p 499–510CrossRef

36.

Y.G. Liu, M.Q. Li, and H.J. Liu, Surface Nanocrystallization and Gradient Structure Developed in the Bulk TC4 Alloy Processed by Shot Peening, J. Alloys Compd., 2016, 685, p 186–193CrossRef

37.

C.C. Tasan, J.P.M. Hoefnagels, and M.G.D. Geers, Identification of the Continuum Damage Parameter: An Experimental Challenge in Modeling Damage Evolution, Acta Mater., 2012, 60(8), p 3581–3589CrossRef

38.

A. Bower, N. Fleck, A. Needleman, and N. Ogbonna, Indentation of a Power Law Creeping Solid, Proc. R. Soc. Lond. Ser. A, 1993, 441(1911), p 97–124CrossRef

39.

M. Mayo and W. Nix, A Micro-indentation Study of Superplasticity in Pb, Sn, and Sn-38 wt.% Pb, Acta Metall., 1988, 36(8), p 2183–2192CrossRef

40.

T.H. Courtney, Mechanical Behavior of Materials, Waveland Press, Long Grove, 2005, p 294–314

41.

X. Liu, Q. Zhang, X. Zhao, X. Yang, and L. Luo, Ambient-Temperature Nanoindentation Creep in Ultrafine-Grained Titanium Processed by ECAP, Mater. Sci. Eng. A, 2016, 676, p 73–79CrossRef

42.

H.E. Evans, Mechanisms of Creep Fracture, Elsevier, Amsterdam, 1984

43.

B.Q. Han, E.J. Lavernia, and F.A. Mohamed, Dislocation Structure and Deformation in Iron Processed by Equal-Channel-Angular Pressing, Metall. Mater. Trans. A, 2004, 35(4), p 1343–1350CrossRef

44.

P. Kral, S. Zherebtsov, G. Salishchev, M. Kvapilova, and V. Sklenicka, Effect of Severe Plastic Deformation on Creep Behaviour of a Ti-6Al-4V Alloy, J. Mater. Sci., 2013, 48(13), p 4789–4795CrossRef

45.

W.J. Evans and G.F. Harrison, Power Law Steady State Creep in α/β Titanium Alloys, J. Mater. Sci., 1983, 18(11), p 3449–3455CrossRef

46.

V. Sklenička, J. Dvořák, and M. Svoboda, Creep in Ultrafine Grained Aluminium, Mater. Sci. Eng. A, 2004, 387(1), p 696–701CrossRef

47.

C. Xu and T.G. Langdon, Creep and Superplasticity in a Spray-Cast Aluminum Alloy Processed by ECA Pressing, Mater. Sci. Eng. A, 2005, 410(12), p 398–401CrossRef

48.

P. Kral, M. Svoboda, J. Dvorak, M. Kvapilova, and V. Sklenicka, Microstructure Mechanisms Governing the Creep Life of Ultrafine-Grained Cu-0.2 wt.%Zr Alloy, Acta Phys. Pol. A, 2012, 122(3), p 457–460CrossRef

Title: Creep Behavior of Commercially Pure Titanium TA2 After Supersonic Fine Particles Bombardment
Authors: Liling Ge
Zhanwei Yuan
Zhenhua Han
Publication date: 03-01-2019
Publisher: Springer US
Published in: Journal of Materials Engineering and Performance / Issue 2/2019
Print ISSN: 1059-9495
Electronic ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-018-3820-x

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 2/2019

Microstructural Properties of Heat-Treated LENS In Situ Additively Manufactured Titanium Aluminide

Threshold Deformation and Mechanical Properties of Al/Al Laminated-Metal Material with Inner Grooves Fabricated by Hot Rolling

Defect Characterization Through Automated Laser Track Trace Identification in SLM Processes Using Laser Profilometer Data

CO2 Corrosion Behavior of Calcite-Covered API 5L X52 Carbon Steel in Aqueous Solutions

Structural, Mechanical, and Electrical Behavior of Ceramic-Reinforced Copper Metal Matrix Hybrid Composites

Effect of Y/Zr Ratio on Inclusions and Mechanical Properties of 9Cr-RAFM Steel Fabricated by Vacuum Melting

Premium Partners