Top

Journal of Intelligent Manufacturing

Published in:

29-04-2014

Glowworm swarm optimization (GSO) for optimization of machining parameters

Authors: Nurezayana Zainal, Azlan Mohd Zain, Nor Haizan Mohamed Radzi, Muhamad Razib Othman

Published in: Journal of Intelligent Manufacturing | Issue 4/2016

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

This study proposes glowworm swarm optimization (GSO) algorithm to estimate an improved value of machining performance measurement. GSO is a recent nature-inspired optimization algorithm that simulates the behavior of the lighting worms. To the best our knowledge, GSO algorithm has not yet been used for optimization practice particularly in machining process. Three cutting parameters of end milling that influence the machining performance measurement, minimum surface roughness, are cutting speed, feed rate and depth of cut. Taguchi method is performed for experimental design. The analysis of variance is applied to investigate effects of cutting speed, feed rate and depth of cut on surface roughness. GSO has improved machining process by estimating a much lower value of minimum surface roughness compared to the results of experimental and particle swarm optimization.

previous article The rough set based approach to generic routing problems: case of reverse logistics supplier selection

next article Risk evaluation in failure mode and effects analysis using fuzzy digraph and matrix approach

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Agrawal, R. K., Pratihar, D. K., & Roy Choudhury, A. (2006). Optimization of CNC isoscallop free form surface machining using a genetic algorithm. International Journal of Machine Tools and Manufacture, 46(7), 811–819.CrossRef

Antony, J., Anand, R. B., Kumar, M., & Tiwari, M. K. (2006). Multiple response optimization using Taguchi methodology and neuro-fuzzy based model. Journal of Manufacturing Technology Management, 17(7), 908–925.CrossRef

Bharathi Raja, S., & Baskar, N. (2012). Application of particle swarm optimization technique for achieving desired milled surface roughness in minimum machining time. Expert Systems with Applications, 39(5), 5982–5989.CrossRef

Ghani, J. A., Choudhury, I. A., & Hassan, H. H. (2004). Application of Taguchi method in the optimization of end milling parameters. Journal of Materials Processing Technology, 145(1), 84–92.CrossRef

Gopalsamy, B. M., Mondal, B., & Ghosh, S. (2009). Taguchi method and ANOVA: An approach for process parameters optimization of hard machining while machining hardened steel. Journal of Scientific & Industrial Research, 68(8), 686–695.

Hamdan, A., Sarhan, A. A., & Hamdi, M. (2012). An optimization method of the cutting parameters in high-speed machining of stainless steel using coated carbide tool for best surface finish. The International Journal of Advanced Manufacturing Technology, 58(1–4), 81–91.CrossRef

Hasçalık, A., & Çaydaş, U. (2008). Optimization of turning parameters for surface roughness and tool life based on the Taguchi method. The International Journal of Advanced Manufacturing Technology, 38(9–10), 896–903.CrossRef

He, D. & Zhu, H. (2010). Glowworm swarm optimization algorithm based on multi-population. In Sixth international conference on natural computation, pp. 2624–2627.

Johari, N. F., Zain, A. M., Mustaffa, N. H., & Udin, A. (2013). Firefly algorithm for optimization problem. Applied Mechanics and Materials, 421, 512–517.CrossRef

Kamaruzaman, A. F., Zain, A. M., Yusuf, S. M., & Udin, A. (2013). Levy flight algorithm for optimization problems-a literature review. Applied Mechanics and Materials, 421, 496–501.CrossRef

Kondapalli, S. P., Chalamalasetti, S. R., & Damera, N. R. (2013). Application of Taguchi based design of experiments to fusion arc weld processes: A review. Internation Journal of Technology and Management, ISSN 1927–9000, 2(1), 1–8.

Krimpenis, A., & Vosniakos, G. C. (2009). Rough milling optimization for parts with sculptured surfaces using genetic algorithms in a Stackelberg game. Journal of Intelligent Manufacturing, 20(4), 447–461.CrossRef

Krishnanand, K. N. & Ghose, D. (2005). Detection of multiple source locations using a glowworm metaphor with applications to collective robotics. In Swarm Intelligence Symposium, 2005. SIS 2005. Proceedings 2005 IEEE (pp. 84–91). IEEE.

Krishnanand, K. N., & Ghose, D. (2006). Theoretical foundations for multiple rendezvous of glowworm-inspired mobile agents with variable local-decision domains. In American control conference, 2006 (p. 6). IEEE.

Krishnanand, K. N., & Ghose, D. (2009). A glowworm swarm optimization based multi-robot system for signal source localization. In Design and control of intelligent robotic systems (pp. 49–68). Springer, Berlin.

Li, L., Liu, F., Chen, B., & Li, C. B. (2013). Multi-objective optimization of cutting parameters in sculptured parts machining based on neural network. Journal of Intelligent Manufacturing. doi:10.1007/s10845-013-0809-z.

Luo, Q. F., & Zhang, J. L. (2011). Hybrid artificial glowworm swarm optimization for solving constrained engineering problem. Advanced Materials Research, 204, 823–827.

Magdum, V. B., & Naik, V. R. (2013). Evaluation and optimization of machining parameter for turning of EN 8 steel. International Journal of Engineering Trends and Technology (IJTT), 4(5), 1564–1568.

Maji, K., & Pratihar, D. K. (2011). Modeling of electrical discharge machining process using conventional regression analysis and genetic algorithms. Journal of Materials Engineering and Performance, 20(7), 1121–1127.CrossRef

Markopoulos, A. P., Manolakos, D. E., & Vaxevanidis, N. M. (2008). Artificial neural network models for the prediction of surface roughness in electrical discharge machining. Journal of Intelligent Manufacturing, 19(3), 283–292.CrossRef

Mohamad, A., Zain, A. M., Bazin, N. E. N., & Udin, A. (2013). Cuckoo search algorithm for optimization problems—a literature review. Applied Mechanics and Materials, 421, 502–506.CrossRef

Motorcu, A. R. (2010). The optimization of machining parameters using the Taguchi method for surface roughness of AISI 8660 hardened alloy steel. Journal of Mechanical Engineering, 56(2010), 391–401.

Nandi, A. K., & Pratihar, D. K. (2004). An expert system based on FBFN using a GA to predict surface finish in ultra-precision turning. Journal of Materials Processing Technology, 155, 1150–1156.CrossRef

Oramus, P. (2010). Improvements to glowworm swarm optimization algorithm. Journal of Computer Science, 11, 7–20.

Periyanan, P. R., Natarajan, U., & Yang, S. H. (2011). A study on the machining parameters optimization of micro-end milling process. International Journal of Engineering, Science and Technology, 3(6), 237–246.

Raju, K. V. M. K., Janardhana, G. R., Kumar, P. N., & Rao, V. D. P. (2011). Optimization of machining conditions for surface roughness in CNC end milling. International Journal of Precision Engineering and Manufacturing, 12(3), 383–391.CrossRef

Sahoo, A. K., Tiwari, M. K., & Mileham, A. R. (2008). Six sigma based approach to optimize radial forging operation variables. Journal of Materials Processing Technology, 202(1), 125–136.CrossRef

Senthilkumaar, J. S., Selvarani, P., & Arunachalam, R. M. (2010). Selection of cutting parameters based on the analysis of surface roughness and flank wear in finish turning and facing of inconel 718 using taguchi technique. Emirates Journal for Engineering Research, 15(2), 7–14.

Sibalija, T. V., & Majstorovic, V. D. (2012). An integrated approach to optimise parameter design of multi-response processes based on Taguchi method and artificial intelligence. Journal of Intelligent Manufacturing, 23(5), 1511–1528.

Tiwari, M. K., Raghavendra, N., Agrawal, S., & Goyal, S. K. (2010). A hybrid Taguchi-immune approach to optimize an integrated supply chain design problem with multiple shipping. European Journal of Operational Research, 203(1), 95–106.CrossRef

Wang, G., Wang, Y., Zhao, J., & Chen, G. (2012). Process optimization of the serial-parallel hybrid polishing machine tool bsed on artificial neural network and genetic algorithm. Journal of Intelligent Manufacturing, 2(3), 365–374.CrossRef

Yusup, N., Zain, A. M., & Hashim, S. Z. M. (2012). Overview of PSO for optimizing process parameters of machining. Procedia Engineering, 29, 914–923.

Zain, A. M., Haron, H., & Sharif, S. (2010a). Application of GA to optimize cutting conditions for minimizing surface roughness in end milling machining process. Expert System with Applications, 37, 4650–4659.CrossRef

Zain, A. M., Haron, H., & Sharif, S. (2010b). Prediction of surface roughness in the end milling machining using artificial neural network. Expert System with Applications, 37, 1755–1768.CrossRef

Zain, A. M., Haron, H., & Sharif, S. (2010c). Simulated annealing to estimate the optimal cutting conditions for minimizing surface roughness in end milling Ti-6Al-4V. Machining Science and Technology, 14, 43–62.CrossRef

Zain, A. M., Haron, H., & Sharif, S. (2011a). Estimation of the minimum machining performance in the abrasive waterjet machining using integrated ANN-SA. Expert Systems with Applications, 38(7), 8316–8326.CrossRef

Zain, A. M., Haron, H., & Sharif, S. (2011b). Integration of simulated annealing and genetic algorithm to estimate optimal solutions for minimising surface roughness in end milling Ti-6AL-4V. International Journal of Computer Integrated Manufacturing, 24, 574–592.CrossRef

Zain, A. M., Haron, H., & Sharif, S. (2011c). Genetic algorithm and simulated annealing to estimate optimal process parameters of the abrasive waterjet machining. Engineering with Computers, 27, 251–259.CrossRef

Zain, A. M., Haron, H., & Sharif, S. (2012a). Integrated ANN-GA for estimating the minimum value for machining performance. International Journal of Production Research, 50(1), 191–213.CrossRef

Zain, A. M., Haron, H., Qasem, S. N., & Sharif, S. (2012b). Regression and ANN models for estimating minimum value of machining performance. Applied Mathematical Modelling, 36(4), 1477–1492.CrossRef

Zainal, N., Zain, A. M., Radzi, N. H. M., & Udin, A. (2013). Glowworm swarm optimization (GSO) algorithm for optimization problems: A state-of-the-art review. Applied Mechanics and Materials, 421, 507–511.CrossRef

Title: Glowworm swarm optimization (GSO) for optimization of machining parameters
Authors: Nurezayana Zainal
Azlan Mohd Zain
Nor Haizan Mohamed Radzi
Muhamad Razib Othman
Publication date: 29-04-2014
Publisher: Springer US
Published in: Journal of Intelligent Manufacturing / Issue 4/2016
Print ISSN: 0956-5515
Electronic ISSN: 1572-8145
DOI: https://doi.org/10.1007/s10845-014-0914-7

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 4/2016

Continuous prediction of manufacturing performance throughout the production lifecycle

Micro-milling performance of AISI 304 stainless steel using Taguchi method and fuzzy logic modelling

An intelligent approach to supplier evaluation in automotive sector

A generalized-exponential decomposition method for the analysis of inhomogeneous assembly/disassembly systems with unreliable machines and finite buffers

Two-echelon fuzzy stochastic supply chain for the manufacturer–buyer integrated production–inventory system

A method for a robust optimization of joint product and supply chain design

Premium Partners