Top

Journal of Materials Science

Published in:

01-09-2014

Influence of plastic deformation on the precipitation of Cr in copper

Authors: A. Chbihi, X. Sauvage, D. Blavette

Published in: Journal of Materials Science | Issue 18/2014

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

The effect of cold rolling on the early-stage precipitation mechanisms of Cr in fcc Cu has been investigated using transmission electron microscopy and atom-probe tomography. The results clearly show that the deformation leads to an acceleration of both the precipitation and coarsening kinetics. However, cold rolling does not change the precipitation sequence. As reported for the non-deformed state, three kinds of precipitate were observed: spheres, ellipsoid, and plates associated to various crystallographic structures and orientation relationships. If the rolling strain is too high, then intensive recrystallization occurs during aging. Recrystallization is also associated with a fast growth of Cr precipitates and a significant drop in mechanical strength.

previous article Controlling foam morphology of polystyrene via surface chemistry, size and concentration of nanosilica particles

next article Fe dopants enhancing ethanol sensitivity of ZnO thin film deposited by RF magnetron sputtering

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Oberdorfer B, Lorenzoni B, Unger K, Sprengel W, Zehetbauer M, Pippan R, Würschum R (2010) Review: absolute concentration of free volume-type defects in ultra-fine grained Fe prepared by high pressure torsion. Scr Mater 63:452–455CrossRef

Morris DG, Munoz-Morris MA (2002) Review: microstructure of severely deformed Al–3Mg and its evolution during annealing. Acta Mater 50:4047–4060CrossRef

Schafler E, Steiner G, Korznikova E, Kerber M, Zehetbauer MJ (2005) Review: lattice defect investigation of ECAP-Cu by means of X-ray line profile analysis, calorimetry and electrical resistometry. Mater Sci Eng A 410–411:169–173CrossRef

Valiev RZ, Langdon TG (2006) Review: principles of equal-channel angular pressing as a processing tool for grain refinement. Prog Mater Sci 51:881–981CrossRef

Zhilyaev AP, Langdon TG (2008) Review: three-dimensional representations of hardness distributions after processing by high-pressure torsion. Prog Mater Sci 53:893–979CrossRef

Munoz-Morris MA, Leon KV, Caballero FG, Morris DG (2012) Review: a study of changes taking place in Cu–Cr–Zr alloy during severe plastic deformation and annealing as evaluated by thermoelectric power measurements. Scr Mater 67:806–809CrossRef

Sauvage X, Chbihi A, Gunderov D, Belozerov EV, Popov AG (2008) Review: decomposition process in a FeAuPd alloy nanostructured by severe plastic deformation. J Mater Sci 43:7293–7298CrossRef

Hornbogen E, Köster U (1978) Recrystallization of metallic materials. In: F. Haessner (ed), Stuttgart

Humphreys FJ, Hatherly M (1995) Recrystallization and related annealing phenomena, 1st edn. Pergamon, Oxford

10.

Jones MJ, Humphreys FJ (2003) Review: interaction of recrystallization and precipitation: the effect of Al₃Sc on the recrystallization behaviour of deformed aluminium. Acta Mater 51:2149–2159CrossRef

11.

Cerri P Leo (2005) Review: influence of severe plastic deformation on aging of Al–Mg–Si alloys. Mater Sci Eng A 410–411:226–229CrossRef

12.

Sha G, Wang YB, Liao XZ, Duan ZC, Ringer SP, Langdon TG (2009) Review: influence of equal-channel angular pressing on precipitation in an Al–Zn–Mg–Cu alloy. Acta Mater 57:3123–3132CrossRef

13.

Cizek J, Prochazka I, Smola B, Stulikova I, Kuzel R, Matej Z, Cherkaska V, Islamgaliev RK, Kulyasova O (2006) Review: microstructure and thermal stability of ultra fine grained Mg-based alloys prepared by high pressure torsion. Mater Sci Forum 503–504:149–154CrossRef

14.

Straumal BB, Baretzky B, Mazilkin AA, Philipp F, Kogtenkova OA, Volkov MN, Valiev RZ (2004) Review: formation of nanograined structure and decomposition of supersaturated solid solution during high pressure torsion of Al–Zn and Al–Mg alloys. Acta Mater 52:4469–4478CrossRef

15.

Horita Z, Ohashi K, Fujita T, Kaneka K, Langdon TG (2005) Review: achieving high strength and high ductility in precipitation-hardened alloys. Adv Mater 17:1599–1602CrossRef

16.

Deschamps A, Livet F, Brechet Y (1998) Review: influence of predeformation on aging in an Al–Zn–Mg alloy—microstructure evolution and mechanical properties. Acta Mater 47:281–292CrossRef

17.

Genevois C, Fabregue D, Deschamps A, Poole WJ (2006) Review: on the coupling between precipitation and plastic deformation in relation with friction stir welding of AA2024 T3 aluminium alloy. Mater Sci Eng A 441:39–48CrossRef

18.

Zhen L, Fei WD, Kang SB, Kim HW (1997) Review: precipitation behaviour of Al–Mg–Si alloys with high silicon content. J Mater Sci 32:1895–1902CrossRef

19.

Kang SB, Zhen L, Kim HW, Lee ST (1996) Review: effect of cold rolling and aging treatment on mechanical property and precipitation behavior in a Al–Mg–Si alloy. Mater Sci Forum 217–222:827–832CrossRef

20.

Vinogradov A, Patlan V, Suzuki Y, Kitagawa K, Kopylov VI (2002) Review: structure and properties of ultra-fine grain Cu–Cr–Zr alloy produced by equal-channel angular pressing. Acta Mater 50:1639–1651CrossRef

21.

Liu Q, Zhang X, Ge Y, Wang J, Cui JH (2006) Review: effect of processing and heat treatment on behavior of Cu–Cr–Zr alloys to railway contact wire. Meta Mater Trans 37A:3233–3238CrossRef

22.

Leon KV, Munoz-Morris MA, Morris DG (2012) Review: optimisation of strength and ductility of Cu–Cr–Zr by combining severe plastic deformation and precipitation. Mater Sci Eng A 536:181–189CrossRef

23.

Fujii T, Nakazawa H, Kato M, Dahmen U (2000) Review: crystallography and morphology of nanosized Cr particles in a Cu 0.2 % Cr alloy. Acta Mater 48:1033–1045CrossRef

24.

Chbihi A, Sauvage X, Blavette D (2012) Review: atomic scale investigation of Cr precipitation in copper. Acta Mater 60:4575–4585CrossRef

25.

Blavette D, Duguay S, Pareige P (2011) Review: atom probe tomography: from physical metallurgy towards microelectronics. Inter J Mater Res 102:1074–1081CrossRef

26.

Vurpillot F, Bostel A, Blavette D (2000) Review: trajectory overlaps and local magnification in three-dimensional atom probe. Appl Phys Lett 76:3127–3129CrossRef

27.

Zhou HT, Zhong JW, Zhou X, Zhao ZK, Li QB (2008) Review: microstructure and properties of Cu–1.0Cr–0.2Zr–0.03Fe alloy. Mater Sci Eng A 498:230–255CrossRef

28.

Wang Z (1991) Physical property of metal material. Metall Ind Press, Beijing, pp 36–52

29.

Dahmen U (1982) Review: orientation relationships in precipitation systems. Acta Metall 30:63–73CrossRef

30.

Knights RW, Wilkes P (1973) Review: precipitation of chromium in copper and copper-nickel base alloys. Metall Trans 4:2389–2393CrossRef

31.

Rdzawski Z, Stobrawa J (1986) Review: structure of coherent chromium precipitates in aged copper alloys. Scr Metall 20:341–344CrossRef

32.

Massalski TB (1987) Phase diagram for binary alloys. ASM, Metals Park, Ohio, p 819

33.

Philippe T, Blavette D (2011) Review: minimum free-energy pathway of nucleation. J Chem Phy 135(134508):1–3

34.

Fillon A, Sauvage X, Pougis A, Bouaziz O, Barbier D, Arruffat R, Toth LS (2012) Review: influence of severe plastic deformation on the precipitation hardening of a FeSiTi steel. J Mater Sci 47:7939–7945CrossRef

35.

Martin JW (1998) Precipitation hardening, 2nd edn. Butterworth-Heinemann, Oxford, p 7

36.

Larché FR (1979) In: Nabarro FRN (ed) Dislocations in solids. North-Halland publishing Company, London, p 135–153.

37.

Legros M, Dehm G, Arzt E, Balk TJ (2008) Review: observation of giant diffusivity along dislocation cores. Science 319:1646–1649CrossRef

38.

Barreau G, Brunel G, Cizeron G, Lacombe P (1970) Review: détermination des coefficients d’hétérdiffusion en volume et aux joints de grains de l’argent dans le cuivre pur et influence des éléments d’addition: chrome, tellure, titane et zirconium, sur ces coefficients. C R Acad Sci C 270:516–519

39.

Barreau G, Brunel G, Cizeron G, Lacombe P (1971) Mem Sci Rev Metall 68:357

40.

Kaur I, Gust W, Kozma L (1989) HandBook of grain and interphase boundary diffusion data, vol 1. Ziegler Press, Stuttgart, p 458

Title: Influence of plastic deformation on the precipitation of Cr in copper
Authors: A. Chbihi
X. Sauvage
D. Blavette
Publication date: 01-09-2014
Publisher: Springer US
Published in: Journal of Materials Science / Issue 18/2014
Print ISSN: 0022-2461
Electronic ISSN: 1573-4803
DOI: https://doi.org/10.1007/s10853-014-8348-3

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 18/2014

Densification of La0.6Sr0.4Co0.2Fe0.8O3 ceramic by flash sintering at temperature less than 100 °C

The effect of fast annealing treatment on the interface structure and electrical properties of Au/Hg3In2Te6 contact

Simple one-step method to produce titanium dioxide–polycaprolactone composite films with increased hydrophilicity, enhanced cellular interaction and improved degradation for skin tissue engineering

An investigation into the relationship between processing, structure and properties for high-modulus PBO fibres: part 3: analysis of fibre microstructure using transmission electron microscopy

The rheological behaviour of concentrated dispersions of graphene oxide

Tetracycline hydrochloride (TCH)-loaded drug carrier based on PLA:PCL nanofibre mats: experimental characterisation and release kinetics modelling

Premium Partners