Issue 8/2018
Content (58 Articles)
Low Solution Temperature Heat Treatment of AlSi9Cu3(Fe) High-Pressure Die-Casting Actual Automotive Components
Silvia Cecchel, Andrea Panvini, Giovanna Cornacchia
Optimization of Process Parameters for the Axial Distortion and Distortion Range During Die Quenching of a Spiral Bevel Gear
Yingtao Zhang, Gang Wang, Wankai Shi, Lin Yang, Zhichao Li
A Study of Tensile Flow and Work-Hardening Behavior of Alloy 617
Aditya Narayan Singh, A. Moitra, Pragna Bhaskar, Arup Dasgupta, G. Sasikala, A. K. Bhaduri
Effect of Overaging on Fatigue Crack Propagation and Stress Corrosion Cracking Behaviors of an Al-Zn-Mg-Cu Alloy Thick Plate
Lianghua Lin, Zhiyi Liu, Xiangnan Han, Wenjuan Liu
Experimental Assessment of High Heating Rates in Induction Heating with Temperature-Sensitive Lacquers
N. Vanderesse, B. Larregain, F. Bridier, P. Bocher
A Review on Micro- and Nanoscratching/Tribology at High Temperatures: Instrumentation and Experimentation
Saeed Zare Chavoshi, Shuozhi Xu
Effect of the Heat Treatment on the Corrosion Resistance of Duplex Stainless Steels
Luca Pezzato, Mattia Lago, Katya Brunelli, Marco Breda, Irene Calliari
Microstructures and Properties of Nanostructured TiN/MoS2/Ag Composite Film Prepared by Pulsed Laser Deposition
Hongjian Guo, Bo Li, Minmin Han, Wenyuan Chen, Zhenyu Zhang, Junhong Jia
High Chromium Cast Irons: Destabilized-Subcritical Secondary Carbide Precipitation and Its Effect on Hardness and Wear Properties
María Agustina Guitar, Sebastián Suárez, Orlando Prat, Martín Duarte Guigou, Valentina Gari, Gastón Pereira, Frank Mücklich
Multipass Scratch Behavior of Borided and Nitrided H13 Steel
R. C. Vega-Morón, G. A. Rodríguez-Castro, L. F. Jiménez-Tinoco, A. Meneses-Amador, J. V. Méndez-Méndez, J. Escobar-Hernández, C. D. Reséndiz-Calderón, J. L. Nava-Sánchez
The Ablation and Oxidation Behaviors of SiC Coatings on Graphite Prepared by Slurry Sintering and Pack Cementation
Reza Aliasgarian, Malek Naderi, Seyyed Ehsan Mirsalehi, Saeed Safi
Correlation Between the Pitting Potential Evolution and Phase Precipitation Kinetics in the 2205 Duplex Stainless Steel
Mustapha Djama, Djaffar Saidi, Abdelaziz Kadri, Nabil Kherrouba, Brahim Mehdi, Stéphane Mathieu, Thierry Schweitzer, Idir Brahim
Replacement of Nitrided 33CrMoV Steel with ESR Hot Work Tool Steels for Motorsport Applications: Microstructural and Fatigue Characterization
Lorella Ceschini, Andrea Morri, Alessandro Morri, Simone Messieri
Cryorolling-Induced Texture, Mechanical Properties and Fracture Behavior of Al-Mg-Si Alloys During Cold Deformation
Xianwei Ren, Yuanchun Huang, Yu Liu
Structural and Mechanical Properties of Zr-Si-N Coatings Deposited by Arc Evaporation at Different Substrate Bias Voltages
B. Warcholinski, T. A. Kuznetsova, A. Gilewicz, T. I. Zubar, V. A. Lapitskaya, S. A. Chizhik, A. I. Komarov, V. I. Komarova, A. S. Kuprin, V. D. Ovcharenko, V. S. Goltvyanytsya
Superhydrophobic Surface of AZ31 Alloy Fabricated by Chemical Treatment in the NiSO4 Solution
M. Yeganeh, M. Omidi, M. Eskandari
Alternative Chromium-Free Passivation Combined with Nano-electrodeposition for Electrogalvanized Steel
Qingyang Li, Fenghuan Li, Maozhong An
Fracture Strength and Surface Magnetic Flux Uniformity in an Isotropic Polymer-Bonded Ring-Shaped Nd-Fe-B Magnet
N. Farzam Mehr, S. Behrangi, M. Ahmadi, A. Kianvash
Effects of Rolling Temperature on the Microstructure and Properties of 2Cr13/316L/9Cr18MoV Stainless Steel Composite Plate Fabricated by Hot-Rolling Bonding Process
Penglin Zhang, Xiaokang Zhao, Bo Yang, Xiaobo Zhang, Rui Cao
A Study on Thermal Conductivity and Stability of Nanofluids Containing Chemically Synthesized Nanoparticles for Advanced Thermal Applications
Sujoy Das, Krishnan Bandyopadhyay, M. M. Ghosh
Toward a Biocompatible and Degradable Battery Using a Mg-Zn-Zr Alloy with β-Tricalcium Phosphate Nanocoating as Anode
Jiaoyang Xia, Zhihao Yuan, Fengshi Cai
Corrosion and Mechanical Degradation of Ni-Ti Superelastic Alloy in Neutral Fluoride Solution
Toshio Ogawa, Hirokaze Takada, Kuniaki Maruoka
Compressive Properties and Energy Absorption of Aluminum Foams with a Wide Range of Relative Densities
Ying Cheng, Yanxiang Li, Xiang Chen, Xu Zhou, Ningzhen Wang
Mechanical Properties and Microstructure of High-Strength Steel Controlled by Hot Stamping Process
Hang Ou, Xu Zhang, Junrui Xu, Guangyao Li, Junjia Cui
Investigation on Target Erosion and Effect of Deposition Rate on Microstructure and Properties of Sputtered Be Coating
Bingchi Luo, Jiqiang Zhang, Wenqi Li, Kai Li, Xuemin Wang, Weidong Wu
Process Parameter Optimization in Refill Friction Spot Welding of 6061 Aluminum Alloys Using Response Surface Methodology
L. Zhou, L. Y. Luo, R. Wang, J. B. Zhang, Y. X. Huang, X. G. Song
Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V
Haider Ali, Hassan Ghadbeigi, Kamran Mumtaz
Microstructure and Wear Resistance of FeCrBSi Plasma-Sprayed Coating Remelted by Gas Tungsten Arc Welding Process
Dong Tianshun, Zheng Xiaodong, Li Yalong, Li Guolu, Zhou Xiukai, Wang Haidou
Development and Characterization of a Novel Ti-Modified High-Si Medium-Mn Steel Possessing Ultra-High Strength and Reasonable Ductility After Hot Rolling
Nicky Kisku, Arnab Sarkar, K. K. Ray, Sumantra Mandal
Recrystallization Behavior and Super-Elasticity of a Metastable β-Type Ti-21Nb-7Mo-4Sn Alloy During Cold Rolling and Annealing
Siyao Lu, Fengcang Ma, Ping Liu, Wei Li, Xinkuan Liu, Xiaohong Chen, Ke Zhang, Qingyou Han, Lai-Chang Zhang
Formation and Toughening Mechanisms of Dispersions in Interfacial Intermetallics of Dissimilar Laser Al/Steel Joints
J. Yang, Z. S. Yu, Y. L. Li, H. Zhang, W. Guo, P. Peng, Y. N. Zhou
Dissimilar Metal Weld Joints of P91/Ni Alloy: Microstructural Characterization of HAZ of P91 and Stress Analysis at the Weld Interfaces
Javed Akram, Prasad Rao Kalvala, Pradeep Chalavadi, Mano Misra
Effect of Deformation Temperature on the Microstructure and Mechanical Properties of High-Strength Low-Alloy Steel During Hot Compression
Chengzhi Zhao, Wilasinee Kingkam, Li Ning, Hexin Zhang, Li Zhiming
Interaction Between Liquid Silver and Graphene-Coated SiC Substrate
Marta Homa, Natalia Sobczak, Jerzy J. Sobczak, Artur Kudyba, Grzegorz Bruzda, Rafał Nowak, Donatella Giuranno, Katarzyna Pietrzak, Marcin Chmielewski
Shear Assisted Processing and Extrusion (ShAPE™) of AZ91E Flake: A Study of Tooling Features and Processing Effects
Jens T. Darsell, Nicole R. Overman, Vineet V. Joshi, Scott A. Whalen, Suveen N. Mathaudhu
Fabrication of 7075-0.25Sc-0.15Zr Alloy with Excellent Damping and Mechanical Properties by FSP and T6 Treatment
Y. F. Mo, C. Y. Liu, G. B. Teng, H. J. Jiang, Y. Chen, Z. X. Yang, Y. Chen, S. C. Han
Effect of Thiourea on the Corrosion Behavior of Aluminum Anode Foil of Aluminum Electrolytic Capacitor
Zixi Fan, Chengfei Zhu, Fengzhen Chang
Friction and Wear Behavior of TiAl Matrix Composites Incorporated with Silver and Molybdenum Disulfide
Bing Xue, Weidong Ma, Yi Liu
Universal Mechanism of Viscoplastic Deformation of Metallic Materials Far from Thermodynamics Equilibrium
E. Zasimchuk, O. Baskova, O. Gatsenko, T. Turchak
Constitutive Behavior and Forming Limit of Mg-Al-Ca-Gd Alloy Sheets at Room and Elevated Temperatures
Kai-Min Yan, Jia-Qing Zhao, Gang Fang
Role of Centrifugal Casting on Electrochemical Corrosion Behavior of A356-SiCp Composite in 3.5 wt.% NaCl
S. Maimunnisa, P. Gore, T. P. D. Rajan, V. S. Raja
High Catalytic Activity of Phenol Photodegradation from Aqueous Solution with Novel Fe-Fe3O4-GO Nanocomposite
Giang H. Le, Quyet T. Ngo, Tuan T. Nguyen, Quang K. Nguyen, Trang T. T. Quan, Loi D. Vu, Gun D. Lee, Tuan A. Vu
Severe Hot Corrosion of the Superalloy IN718 in Mixed Salts of Na2SO4 and V2O5 at 700 °C
Dhananjay Pradhan, Girija Shankar Mahobia, Kausik Chattopadhyay, Vakil Singh
Microstructure and Mechanical Properties of Rapidly Cooled Friction Stir Welded Ti-6Al-4V Alloys
Zhenlei Liu, Yue Wang, Kang Yang, Dejun Yan
Corrosion Behavior of Nano-/Ultrafine-Grained Al-0.2 wt.% Sc Alloy Produced by Accumulative Roll Bonding (ARB)
Mina Vakili, Ehsan Borhani, Ali Ashrafi
Microstructural Characterization and High Strain Rate Plastic Flow Behavior of SMAW Armox500T Steel Joints from Spherical Indentation Experiments
Ambuj Saxena, A. Kumaraswamy, Sanghamitra Sethi, G. Madhusudhan Reddy, Vemuri Madhu
Alleviation of Mechanical Anisotropy in Ultrafine/Nano-grained AZ31 Magnesium Alloy
S. M. Fatemi, A. Zarei-Hanzaki, M. Eskandari, M. Haghshenas
Systematic Insight into Chloride Concentration, Applied Potential and Time Effect on the Passive Film of Cu-Zn-Ni Ternary Alloy in Alkaline Solution
Li Wang, Decheng Kong, Chaofang Dong, Binbin Zhao, Chang He, Yunyang Wan, Cheng Man, Xiaogang Li
The Sliding Wear and Frictional Behavior of M50-10 wt.%(Sn-Ag-Cu) Self-Lubricating Materials at Elevated Temperatures
Xiyao Liu, Xiaoliang Shi, Yuchun Huang, Xiaobin Deng, Zhao Yan, Bing Xue
Study of Tribological Characteristics of Multi-pass SMAW Armox 500T Steel Joints
Ambuj Saxena, A. Kumaraswamy, Vemuri Madhu, G. Madhusudhan Reddy
Fatigue Properties of Ti-6Al-4V Titanium Alloy Friction Stir Welding Joint
Zhenlei Liu, Yue Wang, Shude Ji, Dejun Yan
Multilayered Coatings for High-Temperature Steam Oxidation: TGA Studies up to 1000 °C
T. Dudziak, E. Medvedovski, M. Homa
Fabrication and Mechanical Properties of In Situ Synthesized Ti2AlN/TiAl Composite
Daqun Wang, Dongli Sun, Xiuli Han, Qing Wang, Ningbo Zhang, Feixing Xu
Influence of Porosity and Pore Distributions on Strength Properties of Porous Alumina
Natsumi Miyazaki, Toshihiko Hoshide
Finite Element Simulation and Optimization of Gas-Quenching Process for Tool Steels
Minsu Jung, Seok-Jae Lee, Won-Beom Lee, Kyoung Il Moon
Investigation of the Performance of Flow Models for TWIP Steel
Suleyman Kilic, Fahrettin Ozturk, Catalin R. Picu