Issue 3/2010
Content (36 Articles)
Densification of porous 8 mol% yttria-stabilized zirconia component: modelling and experimental studies
J. Lu, X. C. Song, T. S. Zhang, H. H. Hng, J. Ma
Gadolinium-doped cerium oxide nanorods: novel active catalysts for ethanol reforming
Mario Godinho, Rosana de F. Gonçalves, Edson R. Leite, Cristiane W. Raubach, Neftalí L. V. Carreño, Luiz F. D. Probst, Elson Longo, Humberto V. Fajardo
Synthesis and characterisation of styrene butadiene styrene-g-N-isopropylacrylamide via UV polymerisation for potential use in biomedical applications
James E. Kennedy, Clement L. Higginbotham
Influence of granulated blast furnace slag on the reaction, structure and properties of fly ash based geopolymer
Sanjay Kumar, Rakesh Kumar, S. P. Mehrotra
Modeling of deleterious phase precipitation during isothermal treatments in superduplex stainless steel
J. M. Pardal, S. S. M. Tavares, M. P. Cindra Fonseca, J. A. de Souza, A. Loureiro, E. P. Moura
Degradation behaviour and mechanical properties of magnesium implants in rabbit tibiae
Annett Krause, Nina von der Höh, Dirk Bormann, Christian Krause, Friedrich-Willhelm Bach, Henning Windhagen, Andrea Meyer-Lindenberg
The effect of multi-walled carbon nanotubes addition on the thermo-oxidative decomposition and flammability of PP/MWCNT nanocomposites
Azat D. Rakhimkulov, S. M. Lomakin, I. L. Dubnikova, A. N. Shchegolikhin, E. Ya Davidov, R. Kozlowski
Precipitation-hardening in cast AL–Si–Cu–Mg alloys
F. J. Tavitas-Medrano, A. M. A. Mohamed, J. E. Gruzleski, F. H. Samuel, H. W. Doty
Mechanical behavior of A265 single fibers
Jaeyoung Lim, James Q. Zheng, Karl Masters, Weinong W. Chen
Microstructure and property characterisation of 3-3 Al(Mg)/Al2O3 interpenetrating composites produced by a pressureless infiltration technique
Hong Chang, Rebecca Higginson, Jon Binner
Effect of heat treatment on the mechanical properties of North American jack pine: thermogravimetric study
Duygu Kocaefe, Sandor Poncsak, Junjun Tang, Mohamed Bouazara
Cyclic oxidation and wear of tungsten rods in contact with glass in atmospheric air
C. Dorgans, J.-M. Chaix, L. Boulangé, Y. Bréchet
Wear characteristics of a new type austenitic stainless steel
Jianjian Ye, Zhiwei Lai, Yuhua Wen, Ning Li
Electrokinetic properties of Nd:YAG nanopowder and a high concentration slurry with ammonium poly(acrylic acid) as dispersant
Yao-Hui Lv, Hong Liu, Yuan-Hua Sang, Shu-Jiang Liu, Ting Chen, Hai-Ming Qin, Ji-Yang Wang
Preparation and characterization of electrospun poly(2,5-dicyclohexylphenylene-1,4-ethynylene) (C24H30)n/poly(ethylene oxide) (PEO) hybrid nanofibers
John A. Ajao, Adurafimihan Abiona, Samuel Chigome, Jean Bosco Kana Kana, Malik Maaza
Effect of initial microstructures on hot forging of Ca-containing cast Mg alloys
Masataka Hakamada, Kazunori Shimizu, Tomokazu Yamashita, Akira Watazu, Naobumi Saito, Hajime Iwasaki
A comparative study of different solvothermal methods for the synthesis of Sn2+-doped BaTiO3 powders and their dielectric properties
Yahong Xie, Shu Yin, Takatoshi Hashimoto, Yuichi Tokano, Atsushi Sasaki, Tsugio Sato
Effect of test conditions on the bending strength of a geopolymer-reinforced composite
D. Pernica, P. N. B. Reis, J. A. M. Ferreira, P. Louda
Strain localization of fully dense nanocrystalline Ni sheet
Rongtao Zhu, Jianqiu Zhou, Hua Jiang, Dongsheng Zhang
A visualization of shear strain in processing by high-pressure torsion
Y. Cao, Y. B. Wang, S. N. Alhajeri, X. Z. Liao, W. L. Zheng, S. P. Ringer, T. G. Langdon, Y. T. Zhu
Adsorption behavior of γ-aminopropyl trimethoxysilane on copper foil
Toshio Ogawa, Takuya Nobuta
A facile method for the synthesis of ZnS/polystyrene composite particles and ZnS hollow micro-spheres
Xinjian Cheng, Qiang Zhao, Yingkui Yang, Sie Chin Tjong, Robert K. Y. Li
Calibration of reaction parameters for the improvement of thermal stability and crystalline quality of multi-walled carbon nanotubes
Saveria Santangelo, Giacomo Messina, Giuliana Faggio, Maurizio Lanza, Alessandro Pistone, Candida Milone
Properties of cellulosic fibre reinforced plaster: influence of hemp or flax fibres on the properties of set gypsum
Pierre Dalmay, A. Smith, T. Chotard, P. Sahay-Turner, V. Gloaguen, P. Krausz
The effect of cyclic bending on the mechanical properties and dislocation structures of drawn steel bars
R. B. Figueiredo, E. C. S. Corrêa, W. A. Monteiro, M. T. P. Aguilar, P. R. Cetlin
Critical fluid shear stress analysis for cell–polymer adhesion
Aracely Rocha, Mariah Hahn, Hong Liang
Dislocation evolution in interstitial-free steel during fatigue near the endurance limit
Chia-Chang Shih, New-Jin Ho, Hsing-Lu Huang
Effect of microstructure on thermal expansion behaviour of nanocrystalline metallic materials
Stefano Gialanella, Francesco Marino
The characteristics of granular-bright facet in hydrogen pre-charged and uncharged high strength steels in the very high cycle fatigue regime
Y. D. Li, S. M. Chen, Y. B. Liu, Z. G. Yang, S. X. Li, W. J. Hui, Y. Q. Weng
Effect of silicon content on the microstructure and properties of Fe–Cr–C hardfacing alloys
G. Azimi, M. Shamanian
Characterization and wear behavior of plasma-sprayed Al2O3 and ZrO25CaO coatings on cast iron substrate
N. Krishnamurthy, M. S. Murali, P. G. Mukunda, M. R. Ramesh