Issue 2/2024
Content (17 Articles)
Improvements in steel production technology for main pipelines
S. V. Kuberskii, S. A. Sbitnev, R. E. Velikotsky, D. A. Smolyarchuk, E. L. Vakulenko, S. A. Smolyarchuk
A new method for assessing steel resistance to local carbon dioxide corrosion at gas facilities
R. R. Kantyukov, D. N. Zapevalov, R. K. Vagapov, K. A. Ibatullin, V. V. Yarkovoi
Influence of the initial structure on the efficiency of laser processing of steel
G. I. Brover, E. E. Shcherbakova
Investigation of the effect of modifiers on graphite shape and dimensions in gray cast iron
A. I. Karlina, A. D. Kolosov, M. V. Konstantinova, E. A. Guseva, J. I. Karlina
Evaluation of hot hardening resource of die steel with controlled austenitic transformation during exploitation
A. A. Krugljakow, S. O. Rogachev, P. Yu. Sokolov, V. M. Khatkevich, D. V. Priupolin
Weldability of aluminum alloys based upon the Al–Ca–Zn–Mg system
V. V. Ovchinnikov, T. K. Akopyan, A. G. Sbitnev, D. A. Polyakov
Research and development of the technology for producing fused zirconia
V. A. Sokolov, S. S. Kirov, M. D. Gasparyan
Technological simulation of the process of hot forging of two-layer forgings with deep cavities and an inverted cone
A. A. Myshechkin, I. N. Kravchenko, V. V. Zuev, E. V. Preobrazhenskaya, S. V. Skripnik, A. D. Bykova
Information-modeling system for monitoring heat losses in the lower part of a blast furnace
N. A. Spirin, I. A. Gurin, V. V. Lavrov, A. S. Istomin, L. A. Zaynullin
Numerical simulation of the efficiency of free and forced mixing of liquid metal in a CCM mold
V. I. Odinokov, A. I. Evstigneev, E. A. Dmitriev, V. A. Karpenko, V. V. Petrov
Elastic tension of non-planar strips with asymmetric out-of-flatness for the biquadratic law of stress distribution over the width
S. V. Zakarlyuka, E. A. Rudenko, V. E. Goncharov, V. V. Pilipenko
Analysis and mathematical modeling for microgeometry reproduction of a textured roll surface on a cold-rolled galvanized strip during temper rolling
N. N. Ogarkov, E. Yu. Zvyagina, S. M. Gorbatyuk, E. V. Sheshenin, K. F. Ibragimov
Computer-aided and experimental study of temperature effect on the quality indicators of piercing mandrels when rolling steel 50 vessels on a screw-rolling mill 30–80. part 1
R. L. Shatalov, E. E. Zagoskin, V. A. Medvedev, I. S. Eldeeb
Upgrade of the mechatronic rolls positioning system of the piercing mill
A. V. Tsukanov, K. V. Litsin, S. N. Baskov
Technological and environmental aspects of electronic waste recycling
E. Ye. Zholdasbay, N. K. Dosmukhamedov, A. A. Argyn, M. B. Kurmanseitov, Ye. B. Tazhiev, G. S. Daruesh, G. M. Koishina
Optimization of the treatment of red mud with sulfur dioxide
A. A. Ibrahimov, F. V. Yusubov, R. M. Vekilova
Preliminary study of the technology of vacuum-thermal production of low-carbon ferrochrome
A. I. Volkov, P. E. Stulov, A. F. Charkin, V. P. Panfilov, N. Z. Nurgali, I. A. Krasnyanskaya, M. M. Kospanov, I. I. Masgutov, S. V. Pozharov
