Top

International Journal on Interactive Design and Manufacturing (IJIDeM)

Published in:

07-03-2022 | Technical Paper

Multi-objective genetic algorithm (MOGA) based optimization of high-pressure coolant assisted hard turning of 42CrMo4 steel

Authors: Shanta Saha, Prianka B. Zaman, Md. Imran Hasan Tusar, Nikhil R. Dhar

Published in: International Journal on Interactive Design and Manufacturing (IJIDeM) | Issue 3/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

This study aims at finding a set of optimum solutions of cutting conditions for the machining responses of cutting temperature and surface roughness in hard turning of 42CrMo4 alloy steel at high-pressure coolant (HPC) condition. Comparative experimental investigations between dry and HPC cutting environments were performed to evaluate the stated responses concerning the factors of cutting speed, feed, and work-piece hardness. The full factorial method was employed for the experimental design. The measured value of cutting temperature and surface roughness was found in a reduced amount for HPC condition compared to dry cut for all of the machining runs. Empirical models were developed by response surface methodology for the responses of HPC-assisted machining. The ANOVA result indicated that cutting speed and hardness has the greatest effect on cutting temperature and surface roughness, respectively. Design of experiment (DoE) based optimization was carried out that results in the best optimum settings of 147 m/min cutting speed, 0.12 mm/rev feed rate and 42HRC work-piece hardness. Genetic algorithm based multi-objective optimization was then performed that simultaneously minimizes both of the response models. Within the constraints of experimental design, the optimal set resulted at the range of 86–165 m/min cutting speed, 0.12–0.13 mm/rev feed rate and HRC 42–44 work-piece hardness.

previous article The use of video essays and podcasts to enhance creativity and critical thinking in engineering

next article Enhancement of train braking efficiency by optimal flow control characteristics with aerodynamic braking system

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Wirtschaft"

Online-Abonnement

Mit Springer Professional "Wirtschaft" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 340 Zeitschriften

aus folgenden Fachgebieten:

Bauwesen + Immobilien
Business IT + Informatik
Finance + Banking
Management + Führung
Marketing + Vertrieb
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Senthil Kumar, A., Raja Durai, A., Sornakumar, T.: Machinability of hardened steel using alumina based ceramic cutting tools. Int. J. Refract. Metals Hard Mater. 21(3–4), 109–117 (2003). https://doi.org/10.1016/S0263-4368(03)00004-0CrossRef

Umbrello, D., Rizzuti, S., Outeiro, J.C., Shivpuri, R., M’Saoubi, R.: Hardness-based flow stress for numerical simulation of hard machining AISI H13 tool steel. J. Mater. Process. Technol. 199(1–3), 64–73 (2008). https://doi.org/10.1016/j.jmatprotec.2007.08.018CrossRef

Bogdan, A., Gavrilă, C.: The economic efficiency of replacing grinding with hard turning. Recent 18(2), 71–76 (2017)

Thamizhmanii, S., Hasan, S.: Measurement of surface roughness and flank wear on hard martensitic stainless steel by CBN and PCBN cutting tools. J. Achiev. Mater. Manuf. Eng. 31(2), 415–421 (2008)

List, G., Nouari, M., Géhin, D., Gomez, S., Manaud, J.P., Le Petitcorps, Y., Girot, F.: Wear behaviour of cemented carbide tools in dry machining of aluminium alloy. Wear 259(7–12), 1177–1189 (2005). https://doi.org/10.1016/j.wear.2005.02.056CrossRef

Totten, G.: Handbook of Residual Stress and Deformation of Steel. ASM International, Materials Park, Ohio (2002)

Matsumoto, Y., Barash, M.M., Liu, C.R.: Residual stress in the machined surface of hardened steel. In: High Speed Machining Conference, ASME WAM. pp.193–204. (1984)

Outeiro, J.C., Umbrello, D., M’Saoubi, R.: Experimental and numerical modelling of the residual stresses induced in orthogonal cutting of AISI 316L steel. Int. J. Mach. Tools Manuf. 46(14), 1786–1794 (2006). https://doi.org/10.1016/j.ijmachtools.2005.11.013CrossRef

Ulutan, D., Erdem Alaca, B., Lazoglu, I.: Analytical modelling of residual stresses in machining. J. Mater. Process. Technol. 183(1), 77–87 (2007). https://doi.org/10.1016/j.jmatprotec.2006.09.032CrossRef

10.

Nasr, M.N.A., Ng, E.-G., Elbestawi, M.A.: A modified time-efficient FE approach for predicting machining-induced residual stresses. Finite Elem. Anal. Des. 44(4), 149–161 (2008). https://doi.org/10.1016/j.finel.2007.11.005CrossRef

11.

Kramar, D., Kopač, J.: High pressure cooling in the machining of hard-to-machine materials. J. Mech. Eng. 55(11), 685–694 (2009)

12.

Kamruzzaman, M., Rahman, S.S., Ashraf, Md.Z.I., Dhar, N.R.: Modeling of chip–tool interface temperature using response surface methodology and artificial neural network in HPC-assisted turning and tool life investigation. Int. J. Adv. Manuf. Technol. 90, 1547–1568 (2017). https://doi.org/10.1007/s00170-016-9467-6CrossRef

13.

Machado, A.R., Wallbank, J., Pashby, I.R., Ezugwu, E.O.: Tool performance and chip control when machining tI6Al4v and inconel 901 using high pressure coolant supply. Mach. Sci. Technol. 2(1), 1–12 (1998). https://doi.org/10.1080/10940349808945655CrossRef

14.

Kaminski, J., Alvelid, B.: Temperature reduction in the cutting zone in water-jet assisted turning. J. Mater. Process. Technol. 106(1–3), 68–73 (2000). https://doi.org/10.1016/S0924-0136(00)00640-3CrossRef

15.

Senthil Kumar, A., Rahman, M., Ng, S.L.: Effect of high-pressure coolant on machining performance. Int. J. Adv. Manuf. Technol. 20(2), 83–91 (2002). https://doi.org/10.1007/s001700200128CrossRef

16.

Ezugwu, E.O.: Key improvements in the machining of difficult-to-cut aerospace superalloys. Int. J. Mach. Tools Manuf. 45(12–13), 1353–1367 (2005). https://doi.org/10.1016/j.ijmachtools.2005.02.003CrossRef

17.

Globočki-Lakić, G., Sredanović, B., Kramar, D., Kopač, J.: Machinability of C45e steel - application of minimum quantity lubrication and high pressure jet assisted machining techniques. T FAMENA 40(2), 45–58 (2016). https://doi.org/10.21278/TOF.40204CrossRef

18.

Mia, M., Khan, M.A., Dhar, N.R.: High-pressure coolant on flank and rake surfaces of tool in turning of Ti-6Al-4V: investigations on surface roughness and tool wear. Int. J. Adv. Manuf. Technol. 90(5–8), 1825–1834 (2017). https://doi.org/10.1007/s00170-016-9512-5CrossRef

19.

Umbrello, D., Filice, L.: Improving surface integrity in orthogonal machining of hardened AISI 52100 steel by modeling white and dark layers formation. CIRP Ann. 58(1), 73–76 (2009). https://doi.org/10.1016/j.cirp.2009.03.106CrossRef

20.

Rao, C.J., Rao, D.N., Srihari, P.: Influence of cutting parameters on cutting force and surface finish in turning operation. Procedia Eng. 64, 1405–1415 (2013). https://doi.org/10.1016/j.proeng.2013.09.222CrossRef

21.

Singla, A., Singh, T.: Optimization of process parameters on CNC turning. Int. J. Curr. Eng. Technol. 6(2), 657–661 (2016)

22.

Özel, T., Karpat, Y., Figueira, L., Davim, J.P.: Modelling of surface finish and tool flank wear in turning of AISI D2 steel with ceramic wiper inserts. J. Mater. Process. Technol. 189(1–3), 192–198 (2007). https://doi.org/10.1016/j.jmatprotec.2007.01.021CrossRef

23.

Suresh, R., Basavarajappa, S.: Effect of process parameters on tool wear and surface roughness during turning of hardened steel with coated ceramic tool. Procedia Mater. Sci. 5, 1450–1459 (2014). https://doi.org/10.1016/j.mspro.2014.07.464CrossRef

24.

Bartarya, G., Choudhury, S.K.: Effect of cutting parameters on cutting force and surface roughness during finish hard turning AISI52100 grade steel. Procedia CIRP 1, 651–656 (2012). https://doi.org/10.1016/j.procir.2012.05.016CrossRef

25.

Kant, G., Rao, V.V., Sangwan, K.S.: Predictive modeling of turning operations using response surface methodology. AMM 307, 170–173 (2013). https://doi.org/10.4028/www.scientific.net/AMM.307.170CrossRef

26.

Mia, M., Dhar, N.R.: Effectof high pressure coolant jet on cutting temperature, tool wear and surface finish in turning hardened (HRC 48) steel. J. Mech. Eng. 45(1), 1–6 (2015). https://doi.org/10.3329/jme.v45i1.24376CrossRef

27.

Zahia, H., Athmane, Y.M., Lakhdar, B., Tarek, M.: On the application of response surface methodology for predicting and optimizing surface roughness and cutting forces in hard turning by PVD coated insert. Int. J. Ind. Eng. Comput. 6(2), 267–284 (2015). https://doi.org/10.5267/j.ijiec.2014.10.003CrossRef

28.

Veldhuizen, D.A.V., Lamont, G.B.: Multiobjective evolutionary algorithms: analyzing the state-of-the-art. Evol. Comput. 8(2), 125–147 (2000). https://doi.org/10.1162/106365600568158CrossRef

29.

Amouzgar, K., Bandaru, S., Andersson, T., Ng, A.H.C.: Metamodel-based multi-objective optimization of a turning process by using finite element simulation. Eng. Optim. (2019). https://doi.org/10.1080/0305215X.2019.1639050CrossRef

30.

Mishra, A., Gangele, D.A.: Multi-objective optimization in turning of cylindrical bars of AISI 1045 steel through Taguchi’s method and utility concept. Int. J. Sci. 12(1), 28–36 (2013)

31.

Zerti, A., Yallese, M.A., Meddour, I., Belhadi, S., Haddad, A., Mabrouki, T.: Modeling and multi-objective optimization for minimizing surface roughness, cutting force, and power, and maximizing productivity for tempered stainless steel AISI 420 in turning operations. Int. J. Adv. Manuf. Technol. 102(1–4), 135–157 (2019). https://doi.org/10.1007/s00170-018-2984-8CrossRef

32.

Janahiraman, T.V., Ahmad, N.: Multi objective optimization for turning operation using hybrid extreme learning machine and multi objective genetic algorithm. IJET 7(4.35), 876–879 (2018). https://doi.org/10.14419/ijet.v7i4.35.26273CrossRef

33.

Konak, A., Coit, D.W., Smith, A.E.: Multi-objective optimization using genetic algorithms: a tutorial. Reliab. Eng. Syst. Saf. 91(9), 992–1007 (2006). https://doi.org/10.1016/j.ress.2005.11.018CrossRef

34.

Srinath, R.N., Tirumalaa, D., Gajjelaa, R., Das, R.: ANN and RSM approach for modelling and multi objective optimization of abrasive water jet machining process. Decis. Sci. Lett. 7, 535–548 (2018)

35.

Ameur, T.: Multi-objective particle swarm algorithm for the posterior selection of machining parameters in multi-pass turning. J King Saud Univ Eng Sci. 33, 259–265 (2021)

36.

Öztürk, O., Kalyoncu, M., Ünüvar, A.: Multi objective optimization of cutting parameters in a single pass turning operation using the bees algorithm. In: 1st International Conference on Advances in Mechanical and Mechatronics Engineering, (2018)

37.

Pawar, P.J., Khalkar, M.Y.: Multi-objective optimization of wire-electric discharge machining process using multi-objective artificial bee colony algorithm. Adv. Eng. Optim. Intell. Tech. 949, 39–46 (2020)

38.

Yang, S.H., Natarajan, U.: Multi-objective optimization of cutting parameters in turning process using differential evolution and non-dominated sorting genetic algorithm-II approaches. Int. J. Adv. Manuf. Technol. 49, 773–784 (2010)CrossRef

39.

Deb, K., Goel, T.: Controlled elitist non-dominated sorting genetic algorithms for better convergence. In: Zitzler, E., Thiele, L., Deb, K., Coello Coello, C.A., Corne, D. (eds.) Evolutionary Multi-Criterion Optimization, pp. 67–81. Springer, Berlin, Heidelberg (2001)CrossRef

40.

Onwubolu, G.C., Kumalo, T.: Optimization of multipass turning operations with genetic algorithms. Int. J. Prod. Res. 39(16), 3727–3745 (2001). https://doi.org/10.1080/00207540110056153CrossRefMATH

41.

Quiza Sardiñas, R., Rivas Santana, M., Alfonso Brindis, E.: Genetic algorithm-based multi-objective optimization of cutting parameters in turning processes. Eng. Appl. Artif. Intell. 19(2), 127–133 (2006). https://doi.org/10.1016/j.engappai.2005.06.007CrossRef

42.

Petkovic, D., Radovanovic, M.: Using genetic algorithms for optimization of turning machining process. JESR. 19(1), 47–55 (2016). https://doi.org/10.29081/jesr.v19i1.139CrossRef

43.

Gjelaj, A., Berisha, B., Smaili, F.: Optimization of turning process and cutting force using multiobjective genetic algorithm. Univ. J. Mech. Eng. 7(2), 64–70 (2019)CrossRef

44.

Khan, A.: Effect of high pressure coolant jets in turning TI-6AL-4V alloy with specialized designed nozzle. http://lib.buet.ac.bd:8080/xmlui/handle/123456789/3763 (2015)

45.

Pencheva, T., Atanassov, S.A.: Modelling of a roulette wheel selection operator in genetic algorithms using generalized nets. Bioautomation 13(4), 257–264 (2009)

46.

Wahde, M.: Biologically Inspired Optimization Methods: An Introduction. WIT Press, Southampton, UK, Boston, MA (2008)MATH

47.

Cao, Y.J., Wu, Q.H.: Teaching genetic algorithm using MATLAB. Int. J. Elect. Enging. Educ. 36(2), 139–153 (1999)CrossRef

Title: Multi-objective genetic algorithm (MOGA) based optimization of high-pressure coolant assisted hard turning of 42CrMo4 steel
Authors: Shanta Saha
Prianka B. Zaman
Md. Imran Hasan Tusar
Nikhil R. Dhar
Publication date: 07-03-2022
Publisher: Springer Paris
Published in: International Journal on Interactive Design and Manufacturing (IJIDeM) / Issue 3/2022
Print ISSN: 1955-2513
Electronic ISSN: 1955-2505
DOI: https://doi.org/10.1007/s12008-022-00848-7

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Springer Professional "Wirtschaft"

Other articles of this Issue 3/2022

Response surface design of bellows parameters with negative pressure shrinkage performance

Process optimization and in-mold sensing enabled dimensional prediction for high precision injection molding

Multi-screen dynamic viewpoint system for helicopter simulator

The frame design of a three-wheeled vehicle for a student competition using topology optimization

A holistic educational platform for the study of the smart grid

An interactive study on wear behaviour and mechanical properties of carbonized eggshells filler loaded glass-jute reinforced polyester hybrid bio-composites

Premium Partner