Skip to main content
Top

2020 | OriginalPaper | Chapter

On the Friction Test for Metal Forming Applications

Activate our intelligent search to find suitable subject content or patents.

search-config
loading …

Abstract

The ring compression test is a conventional test for identifying the friction law for metal forming applications. This test is very widely used but has a significant disadvantage. In particular, if the friction stress is high, then a sticking region occurs over a part of the friction surface. In this case, the interpretation of experimental results is difficult because the friction law at sliding is not valid over the sticking region. If the friction stress is very high, then this region occupies the entire friction surface. In this case, the process becomes insensitive to the friction factor at sliding at all. In order to overcome this difficulty and keep the conventional procedure for identifying the friction law, it is proposed to carry out the compression test between fat and conical dies. The geometry of the conical die should be chosen such that no sticking region occurs on the friction surface.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

  • über 102.000 Bücher
  • über 537 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Finance + Banking
  • Management + Führung
  • Marketing + Vertrieb
  • Maschinenbau + Werkstoffe
  • Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

  • über 67.000 Bücher
  • über 390 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Maschinenbau + Werkstoffe




 

Jetzt Wissensvorsprung sichern!

Literature
1.
go back to reference Liu, J.Y.: Upper-bound solutions of some axisymmetric cold forging problems. ASME J. Eng. Ind. 93, 1134–1144 (1971)CrossRef Liu, J.Y.: Upper-bound solutions of some axisymmetric cold forging problems. ASME J. Eng. Ind. 93, 1134–1144 (1971)CrossRef
2.
go back to reference Avitzur, B., Van Tyne, C.J.: Ring formation: an upper bound approach. Part 1: flow pattern and calculation of power. ASME J. Eng. Ind. 104, 231–237 (1982) Avitzur, B., Van Tyne, C.J.: Ring formation: an upper bound approach. Part 1: flow pattern and calculation of power. ASME J. Eng. Ind. 104, 231–237 (1982)
3.
go back to reference Avitzur, B., Van Tyne, C.J.: Ring formation: an upper bound approach. Part 2: process analysis and characteristics. ASME J. Eng. Ind. 104, 238–247 (1982) Avitzur, B., Van Tyne, C.J.: Ring formation: an upper bound approach. Part 2: process analysis and characteristics. ASME J. Eng. Ind. 104, 238–247 (1982)
4.
go back to reference Avitzur, B., Van Tyne, C.J.: Ring formation: an upper bound approach. Part 3: constrained forging and deep drawing applications. ASME J. Eng. Ind. 104, 248–252 (1982) Avitzur, B., Van Tyne, C.J.: Ring formation: an upper bound approach. Part 3: constrained forging and deep drawing applications. ASME J. Eng. Ind. 104, 248–252 (1982)
5.
go back to reference Avitzur, B., Sauerwine, F.: Limit analysis of hollow disk forging. Part 1: upper bound. ASME J. Eng. Ind. 100, 340–344 (1978) Avitzur, B., Sauerwine, F.: Limit analysis of hollow disk forging. Part 1: upper bound. ASME J. Eng. Ind. 100, 340–344 (1978)
6.
go back to reference Lee, J.H.: Upper bound analysis of the upsetting of pressure – sensitive polymeric rings. J. Mater. Process. Technol. 30, 601–612 (1988)MATH Lee, J.H.: Upper bound analysis of the upsetting of pressure – sensitive polymeric rings. J. Mater. Process. Technol. 30, 601–612 (1988)MATH
7.
go back to reference Alexandrov, S.: An analysis of the axisymmetric compression of viscous materials. J. Mater. Process. Technol. 105, 278–283 (2000)CrossRef Alexandrov, S.: An analysis of the axisymmetric compression of viscous materials. J. Mater. Process. Technol. 105, 278–283 (2000)CrossRef
8.
go back to reference Wu, M.-C., Yeh, W.-C.: Effect of natural boundary conditions on the upper-bound analysis of upset forging of ring and disks. Mater. Des. 28, 1245–1256 (2007)CrossRef Wu, M.-C., Yeh, W.-C.: Effect of natural boundary conditions on the upper-bound analysis of upset forging of ring and disks. Mater. Des. 28, 1245–1256 (2007)CrossRef
9.
go back to reference Alexandrov, S., Lyamina, E., Jeng, J.-R.: A general kinematically admissible velocity field for axisymmetric forging and its application to hollow disk forging. Int. J. Adv. Manuf. Technol. 88, 3113–3122 (2017)CrossRef Alexandrov, S., Lyamina, E., Jeng, J.-R.: A general kinematically admissible velocity field for axisymmetric forging and its application to hollow disk forging. Int. J. Adv. Manuf. Technol. 88, 3113–3122 (2017)CrossRef
Metadata
Title
On the Friction Test for Metal Forming Applications
Authors
Sergei Alexandrov
Marko Vilotic
Dragisa Vilotic
Copyright Year
2020
DOI
https://doi.org/10.1007/978-3-030-47883-4_27

Premium Partners