Top

Published in:

2020 | OriginalPaper | Chapter

Performance of Composite Coating on Cutting Tools: Coating Technologies, Performance Optimization, and Their Characterization: A Review

Authors : Vivek Mehta, Rajesh Kumar, Harmesh Kumar

Published in: Advances in Materials Processing

Publisher: Springer Singapore

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Cutting tool development has drawn a lot of attention for the machining of tough to machine materials in the past decade. Conventional cutting tools (such as high-speed steel (HSS), cemented carbide, cubic boron nitride (CBN), etc., have been widely used in the cutting of difficult to machine materials. These cutting tools have limited scope of application due to their wearing during machining, their design, and manufacturing restrictions. To enhance machinability, cutting tools are coated with different nanostructured coating. The indicative properties of such hard coatings are adhesiveness to the substrate, great microhardness, and toughness. Present work reviews the impact of various hard coating (based on Ti, AlN, SiN, and their combinations), forces and surface roughness, and cutting factors (as speed and feed rate) are reviewed. Electrical discharge machining (EDM) is widely used for machining of difficult to machine materials on a large scale, which would be overpriced and impractical to obtain from conventional machining. The cost contribution of tool in the total operation cost of EDM is maximum. Major challenge in the EDM tool is tool wear. Hence, hard coating on the EDM electrode can also be applied in order to restrict the tool wear rate of the EDM electrode, increase the workpiece surface finish and reducing the machining time. In this paper, a coated EDM electrode used for the machining of hard material is also reviewed.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

previous chapter Experimental Investigations on Heat Generation and Surface Roughness During Orthogonal Machining of Stainless Steel Using Bio-based Oil MQL

next chapter Transient Analysis of GTA-Welded Austenitic and Ferritic Stainless Steel

López de Lacalle, L.N., Lamikiz, A., Fernández De Larrinoa, J., Azkona, I.: Advanced cutting tools. In: Machining of Hard Materials, pp. 33–86. Springer London, London (2011). https://doi.org/10.1007/978-1-84996-450-0_2

Özbek, N.A., Çiçek, A., Gülesin, M., Özbek, O.: Investigation of the effects of cryogenic treatment applied at different holding times to cemented carbide inserts on tool wear. Int. J. Mach. Tools Manuf. 86, 34–43 (2014). https://doi.org/10.1016/j.ijmachtools.2014.06.007CrossRef

Serdyuk, Y.D., Semizhon, O.A., Prokopiv, N.M., Petasyuk, G.A., Kharchenko, O.V., Omel’chuk, T.V.: The influence of thermal compression treatment parameters on quality characteristics and wear mechanisms of T5K10 carbide inserts in rough turning. J. Superhard Mater. 33, 120–128 (2011). https://doi.org/10.3103/S1063457611020055

Bushlya, V., Zhou, J., Avdovic, P., Ståhl, J.-E.: Performance and wear mechanisms of whisker-reinforced alumina, coated and uncoated PCBN tools when high-speed turning aged Inconel 718. Int. J. Adv. Manuf. Technol. 66, 2013–2021 (2013). https://doi.org/10.1007/s00170-012-4477-5CrossRef

Dogra, M., Sharma, V.S., Sachdeva, A., Suri, N.M., Dureja, J.S.: Performance evaluation of CBN, coated carbide, cryogenically treated uncoated/coated carbide inserts in finish-turning of hardened steel. Int. J. Adv. Manuf. Technol. 57, 541–553 (2011). https://doi.org/10.1007/s00170-011-3320-8CrossRef

Çalışkan, H., Kurbanoğlu, C., Panjan, P., Kramar, D.: Investigation of the performance of carbide cutting tools with hard coatings in hard milling based on the response surface methodology. Int. J. Adv. Manuf. Technol. 66, 883–893 (2013). https://doi.org/10.1007/s00170-012-4374-yCrossRef

Chen, N., Shen, B., Yang, G., Sun, F.: Tribological and cutting behavior of silicon nitride tools coated with monolayer- and multilayer-microcrystalline HFCVD diamond films. Appl. Surf. Sci. 265, 850–859 (2013). https://doi.org/10.1016/j.apsusc.2012.11.133CrossRef

Kumar, C.H.R.V., Nair, P.K., Ramamoorthy, B.: Characterization of multilayer PVD nanocoatings deposited on tungsten carbide cutting tools. Int. J. Adv. Manuf. Technol. 38, 622–629 (2008). https://doi.org/10.1007/s00170-007-1059-zCrossRef

Minevich, A.A., Eizner, B.A., Gick, L.A., Popok, N.N.: Case studies on tribological behavior of coated cutting tools. Tribol. Trans. 43, 740–748 (2000). https://doi.org/10.1080/10402000008982403CrossRef

10.

Stein, C., Keunecke, M., Bewilogua, K., Chudoba, T., Kölker, W., van den Berg, H.: Cubic boron nitride based coating systems with different interlayers for cutting inserts. Surf. Coatings Technol. 205, S103–S106 (2011). https://doi.org/10.1016/j.surfcoat.2011.03.016CrossRef

11.

Siow, P.C., A. Ghani, J., Ghazali, M.J., Jaafar, T.R., Selamat, M.A., Che Haron, C.H.: Characterization of TiCN and TiCN/ZrN coatings for cutting tool application. Ceram. Int. 39, 1293–1298 (2013). https://doi.org/10.1016/j.ceramint.2012.07.061

12.

Xing, Y., Deng, J., Li, S., Yue, H., Meng, R., Gao, P.: Cutting performance and wear characteristics of Al₂O₃/TiC ceramic cutting tools with WS2/Zr soft-coatings and nano-textures in dry cutting. Wear 318, 12–26 (2014). https://doi.org/10.1016/j.wear.2014.06.001CrossRef

13.

Santecchia, E., Hamouda, A.M.S., Musharavati, F., Zalnezhad, E., Cabibbo, M., Spigarelli, S.: Wear resistance investigation of titanium nitride-based coatings. Ceram. Int. 41, 10349–10379 (2015). https://doi.org/10.1016/j.ceramint.2015.04.152CrossRef

14.

Jahan, M.P., Wong, Y.S., Rahman, M.: A comparative experimental investigation of deep-hole micro-EDM drilling capability for cemented carbide (WC-Co) against austenitic stainless steel (SUS 304). Int. J. Adv. Manuf. Technol. 46, 1145–1160 (2010). https://doi.org/10.1007/s00170-009-2167-8CrossRef

15.

Uhlmann, E., Rosiwal, S., Bayerlein, K., Röhner, M.: Influence of grain size on the wear behavior of CVD diamond coatings in micro-EDM. Int. J. Adv. Manuf. Technol. 47, 919–922 (2010). https://doi.org/10.1007/s00170-009-2131-7CrossRef

16.

Uhlmann, E., Roehner, M.: Investigations on reduction of tool electrode wear in micro-EDM using novel electrode materials. CIRP J. Manuf. Sci. Technol. 1, 92–96 (2008). https://doi.org/10.1016/j.cirpj.2008.09.011CrossRef

17.

Jahan, M.P., Rahman, M., Wong, Y.S.: A review on the conventional and micro-electrodischarge machining of tungsten carbide. Int. J. Mach. Tools Manuf. 51, 837–858 (2011). https://doi.org/10.1016/j.ijmachtools.2011.08.016CrossRef

18.

Kibria, G., Sarkar, B.R., Pradhan, B.B., Bhattacharyya, B.: Comparative study of different dielectrics for micro-EDM performance during microhole machining of Ti–6Al–4V alloy. Int. J. Adv. Manuf. Technol. 48, 557–570 (2010). https://doi.org/10.1007/s00170-009-2298-yCrossRef

19.

Klocke, F.: Using ultra thin electrodes to produce micro-parts with wire-EDM. J. Mater. Process. Technol. (2004). https://doi.org/10.1016/S0924-0136(04)00214-6

20.

Lee, S.H.H., Li, X.P.P.: Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide. J. Mater. Process. Technol. 115, 344–358 (2001). https://doi.org/10.1016/S0924-0136(01)00992-XCrossRef

21.

Jahan, M.P., Wong, Y.S., Rahman, M.: A study on the fine-finish die-sinking micro-EDM of tungsten carbide using different electrode materials. J. Mater. Process. Technol. 209, 3956–3967 (2009). https://doi.org/10.1016/j.jmatprotec.2008.09.015CrossRef

22.

Yu, Z.: Dry electrical discharge machining of cemented carbide. J. Mater. Process. Technol. (2004). https://doi.org/10.1016/S0924-0136(04)00179-7

23.

Kim, C., Kang, M.C., Kim, J.S., Kim, K.H., Shin, B.S., Je, T.J.: Mechanical properties and cutting performance of nanocomposite Cr–Si–N coated tool for green machining. Curr. Appl. Phys. 9, S145–S148 (2009). https://doi.org/10.1016/j.cap.2008.08.054CrossRef

24.

Suzuki, T., Kato, M., Saito, H., Iizuka, H.: Effect of carbon nanotube (CNT) size on wear properties of Cu-based CNT composite electrodes in electrical discharge machining. J. Solid Mech. Mater. Eng. 5, 348–359 (2011). https://doi.org/10.1299/jmmp.5.348CrossRef

25.

Suzuki, T., Konno, T.: Improvement in tool life of electroplated diamond tools by Ni-based carbon nanotube composite coatings. Precis. Eng. 38, 659–665 (2014). https://doi.org/10.1016/j.precisioneng.2014.03.003CrossRef

26.

Soltanieh, M., Aghajani, H., Mahboubi, F., Nekouee, K.A.: Surface characterization of multiple coated H11 hot work tool steel by plasma nitriding and hard chromium electroplating processes. Vacuum 86, 1470–1476 (2012). https://doi.org/10.1016/j.vacuum.2012.01.003CrossRef

27.

Kurahashi, K., Yanagihara, K., Tani, Y., Sato, H.: Repeatable on-the-machine cutting-edge-forming technology applying composite electroplating and anodic electrolysis. CIRP Ann. Manuf. Technol. 53, 53–56 (2004). https://doi.org/10.1016/S0007-8506(07)60643-XCrossRef

28.

Park, H.K., Onikura, H., Ohnishi, O., Sharifuddin, A.: Development of micro-diamond tools through electroless composite plating and investigation into micro-machining characteristics. Precis. Eng. 34, 376–386 (2010). https://doi.org/10.1016/j.precisioneng.2009.09.001CrossRef

29.

Li, H.Y., He, H.B., Han, W.Q., Yang, J., Gu, T., Li, Y.M., Lyu, S.K.: A study on cutting and tribology performances of TiN and TiAlN coated tools. Int. J. Precis. Eng. Manuf. 16, 781–786 (2015). https://doi.org/10.1007/s12541-015-0103-4

30.

Chiou, A.H., Tsao, C.C., Hsu, C.Y.: A study of the machining characteristics of micro EDM milling and its improvement by electrode coating. Int. J. Adv. Manuf. Technol. 78, 1857–1864 (2015). https://doi.org/10.1007/s00170-014-6778-3CrossRef

31.

Sahin, Y., Sur, G.: The effect of Al₂O₃, TiN and Ti (C, N) based CVD coatings on tool wear in machining metal matrix composites. Surf. Coatings Technol. 179, 349–355 (2004). https://doi.org/10.1016/S0257-8972(03)00802-8CrossRef

32.

More, A.S., Jiang, W., Brown, W.D., Malshe, A.P.: Tool wear and machining performance of cBN-TiN coated carbide inserts and PCBN compact inserts in turning AISI 4340 hardened steel. J. Mater. Process. Technol. 180, 253–262 (2006). https://doi.org/10.1016/j.jmatprotec.2006.06.013CrossRef

33.

Dosbaeva, G.K., El Hakim, M.A., Shalaby, M.A., Krzanowski, J.E., Veldhuis, S.C.: Cutting temperature effect on PCBN and CVD coated carbide tools in hard turning of D2 tool steel. Int. J. Refract. Met. Hard Mater. 50, 1–8 (2015). https://doi.org/10.1016/j.ijrmhm.2014.11.001CrossRef

34.

Zhang, K., Deng, J., Meng, R., Gao, P., Yue, H.: Effect of nano-scale textures on cutting performance of WC/Co-based Ti55Al45N coated tools in dry cutting. Int. J. Refract. Met. Hard Mater. 51, 35–49 (2015). https://doi.org/10.1016/j.ijrmhm.2015.02.011CrossRef

35.

Sidorenko, D., Mishnaevsky, L., Levashov, E., Loginov, P., Petrzhik, M.: Carbon nanotube reinforced metal binder for diamond cutting tools. Mater. Des. 83, 536–544 (2015). https://doi.org/10.1016/j.matdes.2015.06.056CrossRef

36.

Bouzakis, K.D., Bouzakis, E., Kombogiannis, S., Paraskevopoulou, R., Skordaris, G., Makrimallakis, S., Katirtzoglou, G., Pappa, M., Gerardis, S., M’Saoubi, R., Andersson, J.M.: Effect of silicon content on PVD film mechanical properties and cutting performance of coated cemented carbide inserts. Surf. Coatings Technol. 237, 379–389 (2013). https://doi.org/10.1016/j.surfcoat.2013.06.044CrossRef

37.

Zhang, K., Deng, J., Sun, J., Jiang, C., Liu, Y., Chen, S.: Effect of micro/nano-scale textures on anti-adhesive wear properties of WC/Co-based TiAlN coated tools in AISI 316 austenitic stainless steel cutting. Appl. Surf. Sci. 355, 602–614 (2015). https://doi.org/10.1016/j.apsusc.2015.07.132CrossRef

38.

Chang, Y.Y., Lai, H.M.: Wear behavior and cutting performance of CrAlSiN and TiAlSiN hard coatings on cemented carbide cutting tools for Ti alloys. Surf. Coatings Technol. 259, 152–158 (2014). https://doi.org/10.1016/j.surfcoat.2014.02.015CrossRef

39.

Kim, M., Chang, D.Y., Jeong, Y.S., Ro, B.H., Lee, K.H.: The wear resistance of electroless nickel and electroless composite (Ni-PX, X: SiC, Al₂O₃, diamond) coating layers. J. Korean Inst. Surf. Eng. 27, 193–206 (1994)

40.

Choy, K.L.: Chemical vapour deposition of coatings (2003). https://doi.org/10.1016/S0079-6425(01)00009-3CrossRef

41.

Vahlas, C., Caussat, B., Serp, P., Angelopoulos, G.N.: Principles and applications of CVD powder technology (2006). https://doi.org/10.1016/j.mser.2006.05.001CrossRef

42.

Sproul, W.D.: Physical vapor deposition tool coatings. Surf. Coatings Technol. 81, 1–7 (1996). https://doi.org/10.1016/0257-8972(95)02616-9CrossRef

43.

König, W., Fritsch, R., Kammermeier, D.: Physically vapor deposited coatings on tools: performance and wear phenomena. Surf. Coatings Technol. 49, 316–324 (1991). https://doi.org/10.1016/0257-8972(91)90076-9CrossRef

44.

Bouzakis, K.D., Michailidis, N., Skordaris, G., Bouzakis, E., Biermann, D., M’Saoubi, R.: Cutting with coated tools: coating technologies, characterization methods and performance optimization. CIRP Ann. Manuf. Technol. 61, 703–723 (2012). https://doi.org/10.1016/j.cirp.2012.05.006CrossRef

45.

Henderer, W., Xu, F.: Hybrid TiSiN, CrC/C PVD coatings applied to cutting tools. Surf. Coatings Technol. 215, 381–385 (2013). https://doi.org/10.1016/j.surfcoat.2012.06.092CrossRef

46.

Wu, W., Chen, W., Yang, S., Lin, Y., Zhang, S., Cho, T.Y., Lee, G.H., Kwon, S.C.: Design of AlCrSiN multilayers and nanocomposite coating for HSS cutting tools. Appl. Surf. Sci. 351, 803–810 (2015). https://doi.org/10.1016/j.apsusc.2015.05.191CrossRef

47.

Vereschaka, A.A., Grigoriev, S.N., Vereschaka, A.S., Popov, A.Y., Batako, A.D.: Nano-scale multilayered composite coatings for cutting tools operating under heavy cutting conditions. In: Procedia CIRP, pp. 239–244. Elsevier (2014). https://doi.org/10.1016/j.procir.2014.03.070

48.

Manjaiah, M., Narendranath, S., Basavarajappa, S., Gaitonde, V.N.: Effect of electrode material in wire electro discharge machining characteristics of Ti50Ni50-xCux shape memory alloy. Precis. Eng. 41, 68–77 (2015). https://doi.org/10.1016/j.precisioneng.2015.01.008CrossRef

49.

Bansal, S.A., Singh, A.P., Kumar, S.: Synergistic effect of graphene and carbon nanotubes on mechanical and thermal performance of polystyrene. Mater. Res. Express. 5, 075602 (2018). https://doi.org/10.1088/2053-1591/aacfc0CrossRef

50.

Raj, S.O.N., Prabhu, S.: Analysis of multi objective optimisation using TOPSIS method in EDM process with CNT infused copper electrode. Int. J. Mach. Mach. Mater. 19, 76–94 (2017). https://doi.org/10.1504/IJMMM.2017.081190CrossRef

51.

Bansal, S.A., Singh, A.P., Kumar, S.: High strain rate behavior of epoxy graphene oxide nanocomposites. Int. J. Appl. Mech. 10, 1850072 (2018). https://doi.org/10.1142/S1758825118500722CrossRef

52.

Bansal, S.A., Singh, A.P., Kumar, S.: Reinforcing graphene oxide nanoparticles to enhance viscoelastic performance of epoxy nanocomposites. J. Nanosci. Nanotechnol. 19, 4000–4006 (2019). https://doi.org/10.1166/jnn.2019.16336CrossRef

53.

Twinkle, Singh, K., Bansal, S.A., Kumar, S.: Graphene oxide (GO)/copper doped hematite (α-Fe₂O₃) nanoparticles for organic pollutants degradation applications at room temperature and neutral pH. Mater. Res. Express. 6, 115026 (2019). https://doi.org/10.1088/2053-1591/ab4459

54.

Zeller, F., Müller, C., Miranzo, P., Belmonte, M.: Exceptional micromachining performance of silicon carbide ceramics by adding graphene nanoplatelets. J. Eur. Ceram. Soc. 37, 3813–3821 (2017)CrossRef

55.

Bansal, S.A., Singh, A.P., Kumar, A., Kumar, S., Kumar, N., Goswamy, J.K.: Improved mechanical performance of bisphenol-A graphene-oxide nano-composites. J. Compos. Mater. 52, 2179–2188 (2018). https://doi.org/10.1177/0021998317741952CrossRef

56.

Bansal, S.A., Singh, A.P., Kumar, S.: 2D materials: graphene and others. In: AIP Conference Proceedings, p. 020459 (2016). https://doi.org/10.1063/1.4946510

57.

Benninghoven, A.: Characterization of coatings. Thin Solid Films 39, 3–23 (1976). https://doi.org/10.1016/0040-6090(76)90620-9CrossRef

58.

Bouzakis, K.D., Michailidis, N., Hadjiyiannis, S., Skordaris, G., Erkens, G.: The effect of specimen roughness and indenter tip geometry on the determination accuracy of thin hard coatings stress-strain laws by nanoindentation. Mater. Charact. 49, 149–156 (2002). https://doi.org/10.1016/S1044-5803(02)00361-3CrossRef

59.

Bansal, S.A., Singh, A.P., Kumar, S., Bansal, S.A.: Reinforcing graphene oxide nano particles to enhance. J. Nanosci. Nanotechnol. 19, 1–7 (2019). https://doi.org/10.1166/jnn.2019.16336CrossRef

60.

Bouzakis, K.D., Michailidis, N., Skordaris, G.: Hardness determination by means of a FEM-supported simulation of nanoindentation and applications in thin hard coatings. Surf. Coatings Technol. 200, 867–871 (2005). https://doi.org/10.1016/j.surfcoat.2005.02.122CrossRef

61.

Beake, B.D.: Evaluation of the fracture resistance of DLC coatings on tool steel under dynamic loading. Surf. Coatings Technol. 198, 90–93 (2005). https://doi.org/10.1016/j.surfcoat.2004.10.048CrossRef

62.

Beake, B.D., Smith, J.F., Gray, A., Fox-Rabinovich, G.S., Veldhuis, S.C., Endrino, J.L.: Investigating the correlation between nano-impact fracture resistance and hardness/modulus ratio from nanoindentation at 25–500 °C and the fracture resistance and lifetime of cutting tools with Ti1-xAlxN (x = 0.5 and 0.67) PVD coatings in milling operations. Surf. Coatings Technol. 201, 4585–4593 (2007). https://doi.org/10.1016/j.surfcoat.2006.09.118

63.

Beake, B.D., Fox-Rabinovich, G.S., Veldhuis, S.C., Goodes, S.R.: Coating optimisation for high speed machining with advanced nanomechanical test methods. Surf. Coatings Technol. 203, 1919–1925 (2009). https://doi.org/10.1016/j.surfcoat.2009.01.025CrossRef

64.

Fateh, N., Fontalvo, G.A., Gassner, G., Mitterer, C.: Influence of high-temperature oxide formation on the tribological behaviour of TiN and VN coatings. Wear 262, 1152–1158 (2007). https://doi.org/10.1016/j.wear.2006.11.006CrossRef

65.

Rodríguez, R.J., García, J.A., Medrano, A., Rico, M., Sánchez, R., Martínez, R., Labrugère, C., Lahaye, M., Guette, A.: Tribological behaviour of hard coatings deposited by arc-evaporation PVD. In: Vacuum, pp. 559–566 (2002). https://doi.org/10.1016/S0042-207X(02)00248-8

66.

Wagner, J., Mitterer, C., Penoy, M., Michotte, C., Wallgram, W., Kathrein, M.: The effect of deposition temperature on microstructure and properties of thermal CVD TiN coatings. Int. J. Refract. Met. Hard Mater. 26, 120–126 (2008). https://doi.org/10.1016/j.ijrmhm.2007.01.010CrossRef

67.

SPIE, Proceedings of: Front Matter: Volume 6606. In: Advanced Laser Technologies 2006, pp. 660601-660601–14. SPIE (2007). https://doi.org/10.1117/12.739509

68.

Liu, A., Deng, J., Cui, H., Chen, Y., Zhao, J.: Friction and wear properties of TiN, TiAlN, AlTiN and CrAlN PVD nitride coatings. Int. J. Refract. Met. Hard Mater. 31, 82–88 (2012). https://doi.org/10.1016/j.ijrmhm.2011.09.010CrossRef

69.

Lin, J.F., Horng, J.H.: Analysis of the tribological behaviour and wear mechanisms of titanium nitride coating. Wear. 171, 59–69 (1994). https://doi.org/10.1016/0043-1648(94)90348-4

70.

Hainsworth, S.V., Soh, W.C.: The effect of the substrate on the mechanical properties of TiN coatings. Surf. Coatings Technol. 163–164, 515–520 (2003). https://doi.org/10.1016/S0257-8972(02)00652-7CrossRef

71.

Guu, Y.Y., Lin, J.F., Ai, C.F.: The tribological characteristics of titanium nitride coatings part I. Coating thickness effects. Wear 194, 12–21 (1996). https://doi.org/10.1016/0043-1648(95)06630-6CrossRef

72.

Guu, Y.Y., Lin, J.F.: The tribological characteristics of titanium nitride coatings Part II. Comparisons of two deposition processes. Wear 194, 22–29 (1996). https://doi.org/10.1016/0043-1648(95)06631-4CrossRef

73.

Azushima, A., Tanno, Y., Iwata, H., Aoki, K.: Coefficients of friction of TiN coatings with preferred grain orientations under dry condition. Wear 265, 1017–1022 (2008). https://doi.org/10.1016/j.wear.2008.02.019CrossRef

74.

Nordin, M., Larsson, M., Hogmark, S.: Wear resistance of multilayered PVD TiN/TaN on HSS. In: Surface and Coatings Technology, pp. 528–534 (1999). https://doi.org/10.1016/S0257-8972(99)00493-4

75.

Nordin, M., Larsson, M., Hogmark, S.: Mechanical and tribological properties of multilayered PVD TiN/CrN, TiN/MoN, TiN/NbN and TiN/TaN coatings on cemented carbide. Surf. Coatings Technol. 106, 234–241 (1998). https://doi.org/10.1016/S0257-8972(98)00544-1CrossRef

76.

Gåhlin, R., Larsson, M., Hedenqvist, P., Jacobson, S., Hogmark, S.: The crater grinder method as a means for coating wear evaluation—an update. Surf. Coatings Technol. 90, 107–114 (1997). https://doi.org/10.1016/S0257-8972(96)03101-5CrossRef

77.

Luo, Q., Hovsepian, P.E., Lewis, D.B., Münz, W.D., Kok, Y.N., Cockrem, J., Bolton, M., Farinotti, A.: Tribological properties of unbalanced magnetron sputtered nano-scale multilayer coatings TiAlN/VN and TiAlCrYN deposited on plasma nitrided steels. Surf. Coatings Technol. 193, 39–45 (2005). https://doi.org/10.1016/j.surfcoat.2004.07.058CrossRef

Title: Performance of Composite Coating on Cutting Tools: Coating Technologies, Performance Optimization, and Their Characterization: A Review
Authors: Vivek Mehta
Rajesh Kumar
Harmesh Kumar
Publisher: Springer Singapore
Book: Advances in Materials Processing
Print ISBN: 978-981-15-4747-8

Electronic ISBN: 978-981-15-4748-5

Copyright Year: 2020
DOI: https://doi.org/10.1007/978-981-15-4748-5_5

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Premium Partners