Issue 4/2020
Content (15 Articles)
Magnetic Nanoparticles as a Strong Contributor to the Biocompatibility of Ferrogels
F. A. Blyakhman, E. B. Makarova, P. A. Shabadrov, F. A. Fadeyev, T. F. Shklyar, A. P. Safronov, S. V. Komogortsev, G. V. Kurlyandskaya
Study of Phase Transitions in the Antiferromagnetic Heisenberg Model on a Body-Centered Cubic Lattice by Monte Carlo Simulation
A. K. Murtazaev, F. A. Kassan-Ogly, M. K. Ramazanov, K. Sh. Murtazaev
Spin-Reorientation Transitions in Multiferroics with Cycloidal Spin Ordering
Z. V. Gareeva, L. A. Kalyakin, I. R. Kayumov, A. K. Zvezdin
Stress-Induced Magnetic Anisotropy Enabling Engineering of Magnetic Softness GMI Effect and Domain Wall Dynamics of Amorphous Microwires
V. Zhukova, P. Corte-Leon, L. González-Legarreta, M. Ipatov, A. Talaat, J. M. Blanco, J. Gonzalez, J. Olivera, A. Zhukov
Investigation of Cyclic Oxidation Behavior of (Cr, Mo, Si)-Containing (α2 + γ) TiAl-Based Alloys Synthesized by ECAS Sintering
Y. Garip, O. Ozdemir
Deformation-Induced Atomic Disordering and bcc → fcc Transformation in Heusler Alloy Ni54Mn21Ga25 Subjected to Megaplastic Deformation by High Pressure Torsion
V. G. Pushin, N. N. Kuranova, E. B. Marchenkova, A. V. Pushin
Composite Structure as a Strengthening Factor of Stainless Austenitic Chromium–Nickel Additive Steel
M. V. Staritsyn, P. A. Kuznetsov, S. N. Petrov, M. S. Mikhailov
Annealing-Induced Structural–Phase Transformations in an Al–Zn–Mg–Fe–Ni Alloy after High Pressure Torsion
I. G. Shirinkina, I. G. Brodova
Observation of the Martensitic-Austenitic Component in the Structure of Low-Carbon Low-Alloy Pipe Steel
I. L. Yakovleva, N. A. Tereshchenko, N. V. Urtsev
Analysis of the Microstructure, Phase Composition, and Oxidation Kinetics of Heat-Resistant Titanium Alloys with Gadolinium
A. A. Popov, M. O. Leder, M. C. Karabanalov, E. N. Popova, I. V. Narygina
Structure, Phase Composition, and Mechanical Properties of Biocompatible Titanium Alloys of Different Types
A. G. Illarionov, A. G. Nezhdanov, S. I. Stepanov, G. Muller-Kamskii, A. A. Popov
Microstructure Analysis and Optimization of Parameters for Improved Properties in High Strength AA8079 (Al–Fe–Cu–Si–Zn)
M. Meignanamoorthy, M. Ravichandran
Effects of Growth Rate on Eutectic Spacing, Microhardness, and Ultimate Tensile Strength in the Al–Cu–Ti Eutectic Alloy
Ümit Bayram, Necmettin Maraşlı
Dynamic Strength of Submicrocrystalline and Nanocrystalline Copper Obtained by High-Strain-Rate Deformation
I. V. Khomskaya, S. V. Razorenov, G. V. Garkushin, E. V. Shorokhov, D. N. Abdullina
Changes in the Mechanical Properties of High-Chromium Economically Alloyed Pipe Steel Depending on Tempering Conditions after Intercritical Quenching
A. N. Makovetskii, D. A. Mirzaev, L. I. Yusupova, A. O. Krasnotalov, A. A. Mirzoev, S. A. Sozykin