Top

Published in:

2020 | OriginalPaper | Chapter

Strain Monitoring During Laser Metal Deposition of Inconel 718 by Neutron Diffraction

Authors : S. Cabeza, B. Özcan, J. Cormier, T. Pirling, S. Polenz, F. Marquardt, T. C. Hansen, E. López, A. Vilalta-Clemente, C. Leyens

Published in: Superalloys 2020

Publisher: Springer International Publishing

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

In this study, we provide novel in situ monitoring of strain during laser metal deposition of Inconel 718 by neutron diffraction. Thermal, phase and stress-related contributions to the lattice parameter evolution are addressed for the representative regions during processing: melt pool, near melt pool, and far-field. The evolution showed a strong dependency on the build height and distance to the melt pool, i.e., time and temperature gradient, as expected. The different regions of interest reached at different moments the processing stable regime, which is contrasted with microstructural characterization. A homogeneous microstructure of coarse epitaxial dendrites and Laves phase was found from the third printed layer on, with fine globular delta phase precipitation at the grain boundaries. In comparison, neutron diffraction strain monitoring highlighted an offset of process stabilization after 24 layers for the melt pool and near-melt pool regions.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

previous chapter Additive Manufacturability of Nickel-Based Superalloys: Composition-Process Induced Vapourization

next chapter Development of a New Alumina-Forming Crack-Resistant High-γ′ Fraction Ni-Base Superalloy for Additive Manufacturing

Frazier WE (2014) Metal additive manufacturing: A review. J. Mater. Eng. Perform. 23: 1917–1928. https://doi.org/10.1007/s11665-014-0958-z.

Bandyopadhyay A, Traxel KD (2018) Invited review article: Metal-additive manufacturing—Modeling strategies for application-optimized designs. Addit. Manuf. 22: 758–774. https://doi.org/10.1016/j.addma.2018.06.024.

Hosseini E, Popovich VA (2019) A review of mechanical properties of additively manufactured Inconel 718. Addit. Manuf. 30: 100877. https://doi.org/10.1016/j.addma.2019.100877.

Abioye TE, Folkes J, Clare AT (2013) A parametric study of Inconel 625 wire laser deposition. J. Mater. Process. Technol. 213: 2145–2151. https://doi.org/10.1016/j.jmatprotec.2013.06.007.

Busachi A, Erkoyuncu J, Colegrove P, Martina F, Ding J (2015) Designing a WAAM based manufacturing system for defence applications. Procedia CIRP. 37: 48–53. https://doi.org/10.1016/j.procir.2015.08.085.

Cheng L, Liang X, Bai J, Chen Q, Lemon J, To A (2019) On utilizing topology optimization to design support structure to prevent residual stress induced build failure in laser powder bed metal additive manufacturing. Addit. Manuf. 27: 290–304. https://doi.org/10.1016/j.addma.2019.03.001.

Bartlett JL, Li X (2019) An overview of residual stresses in metal powder bed fusion. Addit. Manuf. 27: 131–149. https://doi.org/10.1016/j.addma.2019.02.020.

Sames WJ, Unocic KA, Dehoff RR, Lolla T, Babu SS (2014) Thermal effects on microstructural heterogeneity of Inconel 718 materials fabricated by electron beam melting. J. Mater. Res. 29: 1920–1930. https://doi.org/10.1557/jmr.2014.140.

Zhai Y, Lados DA, Brown EJ, Vigilante GN (2019) Understanding the microstructure and mechanical properties of Ti-6Al-4V and Inconel 718 alloys manufactured by Laser Engineered Net Shaping. Addit. Manuf. 27: 334–344. https://doi.org/10.1016/j.addma.2019.02.017.

10.

Lass EA, Stoudt MR, Williams ME, Katz MB, Levine LE, Phan TQ, Gnaeupel-Herold TH (2017) Formation of the Ni3Nb δ-Phase in Stress-Relieved Inconel 625 Produced via Laser Powder-Bed Fusion Additive Manufacturing. Metall. Mater. Trans. A. 48: 5547–5558. https://doi.org/10.1007/s11661-017-4304-6.

11.

Zhang F, Levine LE, Allen AJ, Stoudt MR, Lindwall G, Lass EA, Williams ME, Idell Y, Campbell CE (2018) Effect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusion. Acta Mater. 152: 200–214. https://doi.org/10.1016/j.actamat.2018.03.017.

12.

Chang SH (2009) In situ TEM observation of γ′, γ″ and δ precipitations on Inconel 718 superalloy through HIP treatment. J. Alloys Compd. 486: 716–721. https://doi.org/10.1016/j.jallcom.2009.07.046.

13.

Denlinger ER, Jagdale V, Srinivasan VG, El-Wardany T, Michaleris p (2016) Thermal modeling of Inconel 718 processed with powder bed fusion and experimental validation using in situ measurements. Addit. Manuf. 11 7–15. https://doi.org/10.1016/j.addma.2016.03.003.

14.

Ni M, Chen C, Wang X, Wang P, Li, Zhang X, Zhou K (2017) Anisotropic tensile behavior of in situ precipitation strengthened Inconel 718 fabricated by additive manufacturing. Mater. Sci. Eng. A. 701: 344–351. https://doi.org/10.1016/j.msea.2017.06.098.

15.

[15] Thiede T, Cabeza S, Mishurova T, Nadammal N, Kromm A, Bode J, Haberland C, Bruno G (2018) Residual Stress in Selective Laser Melted Inconel 718: Influence of the removal from base plate and deposition hatch lengh. Mat Perform and Charact 7 (4): 717–735. https://doi.org/10.1520/mpc20170119.

16.

Lu Y, Wu S, Gan Y, Huang T, Yang C, Junjie L, Lin J (2015) Study on the microstructure, mechanical property and residual stress of SLM Inconel-718 alloy manufactured by differing island scanning strategy. Opt. Laser Technol. 75: 197–206. https://doi.org/10.1016/j.optlastec.2015.07.009.

17.

Mishurova T, Cabeza S, Thiede T, Nadammal N, Kromm A, Klaus M, Genzel C, Haberland C, Bruno G (2018) The Influence of the Support Structure on Residual Stress and Distortion in SLM Inconel 718 Parts. Metall. Mater. Trans. A 49: 3038–3046. https://doi.org/10.1007/s11661-018-4653-9.

18.

Nadammal N, Cabeza S, Mishurova T, Thiede T, Kromm A, Seyfert C, Farahbod L, Haberland C, Schneider JA, Portella PD, Bruno G (2017) Effect of hatch length on the development of microstructure, texture and residual stresses in selective laser melted superalloy Inconel 718. Mater. Des. 134: 139–150. https://doi.org/10.1016/j.matdes.2017.08.049.

19.

Hutchings MT, Krawitz AD (ed) (1992) Measurement of Residual and Applied Stress Using Neutron Diffraction, Springer Science & Business Media, Dordrecht.

20.

Webster GA, Wimpory RW(ed) (2001) ISO/TTA 3:2001 Polycrystalline materials: Determination of residual stresses by neutron diffraction.

21.

Wang Z, Denlinger E, Michaleris P, Stoica AD, Ma D, Beese AM (2017) Residual stress mapping in Inconel 625 fabricated through additive manufacturing: Method for neutron diffraction measurements to validate thermomechanical model predictions. Mater. Des. 113: 169–177. https://doi.org/10.1016/j.matdes.2016.10.003.

22.

Bilheux H, Song G, An K, Bilheux J, Stoica A, Kirka M, Dehoff R, Santodonato L, Gorti S, Radhakrishnan B (2016) Neutron Characterization of Additively Manufactured Inconel 718. Adv. Mater. Process. 175: 16–20.

23.

Aba-Perea PE, Pirling T, Preuss M (2016) In-situ residual stress analysis during annealing treatments using neutron diffraction in combination with a novel furnace design. Mater. Des. 110: 925–931. https://doi.org/10.1016/j.matdes.2016.07.078.

24.

Everton SK, Hirsch M, Stavroulakis PI, Leach RK, Clare AT (2016) Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing. Mater. Des. 95: 431–445. https://doi.org/10.1016/j.matdes.2016.01.099.

25.

An K, Skorpenske HD, Stoica AD, Ma D, Wang XL, Cakmak E(2011) First in situ lattice strains measurements under load at VULCAN, Metall. Mater. Trans. A 42: 95–99. https://doi.org/10.1007/s11661-010-0495-9.

26.

Leung CLA, Marussi S, Atwood RC, Towrie M, Withers PJ, Lee PD (2018) In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing, Nat. Commun. 9: 1–9. https://doi.org/10.1038/s41467-018-03734-7.

27.

Pirling T, Bruno G, Withers PJ (2006) SALSA: Advances in residual stress measurement at ILL. Mater. Sci. Forum. 524–525: 217–222. https://doi.org/10.4028/www.scientific.net/msf.524-525.217.

28.

Davis JR (ed) (1994) ASM Specialty Handbook: Nickel, Cobalt, and Their Alloys. ASM International, Materials Park OH.

29.

Ramachandran D, Kamalan Kirubaharan AM, Rabel AM, Kuppusami P (2015) Thermal expansion behaviour of inconel-690 by in-situ high temperature X-ray diffraction. Mater. Sci. Forum, 830–831: 367–370. https://doi.org/10.4028/www.scientific.net/MSF.830-831.367.

30.

Kamalan KK, Kuppusami P, Dharini T(2018) Thermal expansion studies of electron beam evaporated yttria films on Inconel-718 substrates, Surf. Coatings Technol. 354: 297–305. https://doi.org/10.1016/j.surfcoat.2018.09.034.

31.

Karunaratne MSA, Kyaw S, Jones A, Morrell R, Thomson RC(2016) Modelling the coefficient of thermal expansion in Ni-based superalloys and bond coatings, J. Mater. Sci. 51: 4213–4226. https://doi.org/10.1007/s10853-015-9554-3.

32.

Courbion G, Ferey G (1988) Na2Ca3Al2F14: A new example of a structure with “independent F⁻”—A new method of comparison between fluorides and oxides of different formula, J. Solid State Chem. 76: 426–431. https://doi.org/10.1016/0022-4596(88)90239-3.

33.

[33] Lacaze J, Dehmas M, Niang A, Viguier B (2011) TEM study of high-temperature precipitation of delta phase in inconel 718 alloy, Adv. Mater. Sci. Eng. 2011:1–9. https://doi.org/10.1155/2011/940634.

34.

Radhakrishna C, Rao KP, Srinivas S (1995) Laves phase in superalloy 718 weld metals, J. Mater. Sci. Lett. 14: 1810–1812. https://doi.org/10.1007/bf00271015.

35.

Frank RB, Roberts CG, Zhang J (2010) Effect of nickel content on delta solvus temperature and mechanical properties of alloy 718, 7th Int. Symp. Superalloy 718 and Deriv. Pittsburgh, Pennsylvania, USA, 10–13 October 2010. https://doi.org/10.1002/9781118495223.ch56.

36.

Nandwana P, Kirka M, Okello A, Dehoff R (2018) Electron beam melting of Inconel 718: effects of processing and post-processing, Mater. Sci. Technol. 34: 612–619. https://doi.org/10.1080/02670836.2018.1424379.

37.

Mercelis P, Kruth JP (2005) Residual stresses in Selective Laser Sintering and Selective Laser Melting. 16th Solid Free. Fabr. Symp. SFF 2005 Austin, TX, August 1–3 2005.

38.

Hussein A, Hao L, Yan C, Everson R (2013) Finite element simulation of the temperature and stress fields in single layers built without-support in selective laser melting, Mater. Des. 52: 638–647. https://doi.org/10.1016/j.matdes.2013.05.070.

39.

An K, Yuan L, Dial L, Spinelli I, Stoica AD, Gao Y (2017) Neutron residual stress measurement and numerical modeling in a curved thin-walled structure by laser powder bed fusion additive manufacturing, Mater. Des. 135: 122–132. https://doi.org/10.1016/j.matdes.2017.09.018.

40.

Cabeza S, Cabrera A, Mikhenkova A, Rinaldi D, Ozcan B, Pirling T (2019) Non-destructive assessment of 3D Residual Strain fields in metal additive manufactured components. 4th ASTM Symp. Struct. Integr. Add. Man. Mater. And Parts, Oxon Hill, MD USA, 7–10 October 2019.

41.

Brown DW, Adams DP, Balogh L, Carpenter JS, Clausen B, Livescu V, Martinez RM, Morrow BM, Palmer TA, Pokharel R, Strantza M, Vogel SC (2019) Using In Situ Neutron Diffraction to Isolate Specific Features of Additively Manufactured Microstructures in 304L Stainless Steel and Identify Their Effects on Macroscopic Strength. Metall. Mater. Trans. A 50: 3399–3413. https://doi.org/10.1007/s11661-019-05240-x.

42.

Biegler M, Graf B, Rethmeier M (2018) In-situ distortions in LMD additive manufacturing walls can be measured with digital image correlation and predicted using numerical simulations. Addit. Manuf. 20: 101–110. https://doi.org/10.1016/j.addma.2017.12.007.

43.

Dunbar AJ, Denlinger ER, Heigel J, Michaleris P, Guerrier P, Martukanitz R, Simpson TW (2016) Development of experimental method for in situ distortion and temperature measurements during the laser powder bed fusion additive manufacturing process. Addit. Manuf. 12: 25–30. https://doi.org/10.1016/j.addma.2016.04.007.

44.

Heigel JC, Michaleris P, Palmer TA (2015) In situ monitoring and characterization of distortion during laser cladding of Inconel® 625. J. Mater. Process. Technol. 220: 135–145. https://doi.org/10.1016/j.jmatprotec.2014.12.029.

Title: Strain Monitoring During Laser Metal Deposition of Inconel 718 by Neutron Diffraction
Authors: S. Cabeza
B. Özcan
J. Cormier
T. Pirling
S. Polenz
F. Marquardt
T. C. Hansen
E. López
A. Vilalta-Clemente
C. Leyens
Publisher: Springer International Publishing
Book: Superalloys 2020
Print ISBN: 978-3-030-51833-2

Electronic ISBN: 978-3-030-51834-9

Copyright Year: 2020
DOI: https://doi.org/10.1007/978-3-030-51834-9_101

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Premium Partners