nach oben

Journal of Materials Engineering and Performance

Erschienen in:

01.04.2015

Finite Element Analysis of Plastic Deformation During Impression Creep

verfasst von: Naveena, J. Ganesh Kumar, M. D. Mathew

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 4/2015

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Finite element (FE) analysis of plastic deformation associated with impression creep deformation of 316LN stainless steel was carried out. An axisymmetric FE model of 10 × 10 × 10 mm specimen with 1-mm-diameter rigid cylindrical flat punch was developed. FE simulation of impression creep deformation was performed by assuming elastic-plastic-power-law creep deformation behavior. Evolution of the stress with time under the punch during elastic, plastic, and creep processes was analyzed. The onset of plastic deformation was found to occur at a nominal stress about 1.12 times the yield stress of the material. The size of the developed plastic zone was predicted to be about three times the radius of the punch. The material flow behavior and the pile-up on specimen surface have been modeled.

Vorheriger Artikel A Comparative Study of Ni49.9Ti50.1 and Ni50.3Ti29.7Hf20 Tube Actuators

Nächster Artikel Microstructure-Tensile Properties Correlation for the Ti-6Al-4V Titanium Alloy

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

M.D. Mathew, Naveena, and D. Vijayanand, Impression Creep Behavior of 316LN Stainless Steel, J. Mater. Eng. Perform., 2013, 22, p 492–497CrossRef

Naveena, V.D. Vijayanand, V. Ganesan, K. Laha, and M.D. Mathew, Evaluation of the Effect of Nitrogen on Creep Properties of 316LN Stainless Steel from Impression Creep Tests, Mater. Sci. Eng. A., 2012, 552, p 112–118CrossRef

J.C.M. Li and S.N.G. Chu, Impression Creep: A New Creep Test, J. Mater. Sci., 1977, 12, p 2200–2208CrossRef

T.H. Hyde, W. Sun, and C.J. Hyde, Small Specimen Creep Testing, Applied Creep Mechanics, McGraw-Hill Education, New York, 2013, p 327–334.

I. Sneddon, The Relation Between Load and Penetration in the Axisymmetric Boussinesq Problem for a Punch of Arbitrary Profile, Int. J. Eng. Sci., 1965, 3, p 47–57CrossRef

K.L. Johnson, Contact Mechanics, Cambridge University Press, Cambridge, 1987

D.A. Hills, D. Nowell, and A. Sackfield, Mechanics of Elastic Contacts, Butterworth, Oxford, 1993

G. Feng, S. Qu, Y. Huang, and W.D. Nix, An Analytical Expression for the Stress Field Around an Elastoplastic Indentation/Contact, Acta. Mater., 2007, 55, p 2929–2938CrossRef

F. Yang, J.C.M. Li, and C.W. Shih, Computer Simulation of Impression Creep using the Hyperbolic Sine Stress Law, Mater. Sci. Eng. A., 1995, 201, p 50–57CrossRef

10.

E.C. Yu and J.C.M. Li, Impression Creep of LiF Single Crystals, Philos. Mag., 1977, 36(4), p 811–825CrossRef

11.

T.H. Hyde, K.A. Yehia, and A.A. Becker, Interpretation of Impression Creep Data using a Reference Approach, Int. J. Mech. Sci., 1993, 35, p 451–462CrossRef

12.

Y.C. Lu, S.N.V.R.K. Kurapati, and F. Yang, Finite Element Analysis of Cylindrical Indentation for Determining Plastic Properties of Materials in Small Volumes, J. Phys. D Appl. Phys., 2008, 11, p 115415–115500CrossRef

13.

ABAQUS Inc., ABAQUS Theory Manual, Hibbitt, Karlson, and Sorensen, Inc., Pawtucket, 2010

14.

RCC-MR, 2007, Design and Construction Rules for Mechanical Components of Nuclear Installations, Section 2, Subsection Z.A3.3S.22, AFCEN, Paris, 2007

15.

V. Ganesan, M.D. Mathew, and K. Bhanu Sankara Rao, Influence of Nitrogen on Tensile Properties of 316LN SS, Mater. Sci. Technol., 2009, 25, p 614–618CrossRef

16.

J. Ganesh Kumar, M. Chowdar, V. Ganesan, R.K. Paretkar, K. Bhanu Sankara Rao, and M.D. Mathew, High Temperature Design Curves for High Nitrogen Grades of 316LN Stainless Steel, Nucl. Eng. Des., 2010, 240, p 1363–1370CrossRef

17.

A.C. Fischer-Cripps, Introduction to Contact Mechanics, Springer, New York, 2000

18.

R.T. Shield, On the Plastic Flow of Metals Under Conditions of Axial Symmetry, Proc. R. Soc., 1956, 233, p 267–287CrossRef

19.

G. Eason, R.T. Shield, and F. Angew, The Plastic Indentation of a Semi-infinite Solid by a Perfectly Rough Circular Punch, Math. M. Phy., 1960, 11, p 33–42

20.

J.W. Harding and L.N. Sneddon, The Elastic Stresses Produced by the Indentation of the Plane Surface of a Semi-infinite Elastic Solid by a Rigid Punch, Proc. Cambridge Phil. Soc., 1945, 41, p 16–26CrossRef

21.

H.Y. Yu, M.A. Imam, and B.B. Rath, Study of the Deformation Behaviour of Homogeneous Materials by Impression Tests, J. Mater. Sci., 1985, 20, p 636–642CrossRef

22.

D. Tabor, A Simple Theory of Static and Dynamic Hardness, Proc. R. Soc. Lond. A., 1948, 192, p 247–274CrossRef

23.

S. Timoshenko, Theory of Elasticity, McGraw Hill, New York, 1934, p 344

24.

D.R. Hayhurst and J.T. Henderson, Creep Stress Redistribution in Notched Bars, Int. J. Mech. Sci., 1977, 19, p 133–146CrossRef

25.

G. Eggeler and C. Wiesner, A Numerical Study of Parameters Controlling Stress Redistribution in Circular Notched Specimens During Creep, J. Strain. Anal., 1993, 28, p 13–22CrossRef

26.

S. Goyal, K. Laha, C.R. Das, P. Panneerselvi, and M.D. Mathew, Finite Element Analysis of Effect of Tri-axial State of Stress on Creep Cavitation and Rupture Behavior of 2.25Cr-1Mo steel, Int. J. Mech. Sci., 2013, 75, p 233–243CrossRef

27.

H.Y. Yu and J.C.M. Li, Computer Simulation of Impression Creep by the Finite Element Method, J. Mater. Sci., 1977, 12, p 2214–2222CrossRef

28.

D. Pan and I. Dutta, A Mechanics-Induced Complication of Impression Creep and Its Solution: Application to Sn-3.5Ag Solder, Mater. Sci. Eng. A., 2004, 379, p 154–163CrossRef

29.

G. Das, S. Ghosh, S. Ghosh, and R.N. Ghosh, Materials Characterization and Classification on the Basis of Materials Pile-up Surrounding the Indentation, Mater. Sci. Eng. A., 2005, 408, p 158–164CrossRef

Titel: Finite Element Analysis of Plastic Deformation During Impression Creep
verfasst von: Naveena
J. Ganesh Kumar
M. D. Mathew
Publikationsdatum: 01.04.2015
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 4/2015
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-014-1225-z

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 4/2015

Effect of Heat Treatment on the Microstructure and Hardness of 17Cr-0.17N-0.43C-1.7 Mo Martensitic Stainless Steel

Corrosion Behavior of Mg-6Al-1Zn+XRE Magnesium Alloy with Minor Addition of Yttrium

Strain-Induced Martensite Formation and Recrystallization Behavior in 304 Stainless Steel

Microstructure-Tensile Properties Correlation for the Ti-6Al-4V Titanium Alloy

Study of Coating Growth Behavior During the Plasma Electrolytic Oxidation of Magnesium Alloy ZK60

Influence of Nitrogen Flow Rates on the Structure, Hardness, and Electrical Resistivity of HfN Coatings by DC Sputtering

Premium Partner

Marktübersichten