Skip to main content

2016 | OriginalPaper | Buchkapitel

Implementation of Taguchi Method in the Optimization of Roller Burnishing Process Parameter for Surface Roughness

Aktivieren Sie unsere intelligente Suche um passende Fachinhalte oder Patente zu finden.

search-config
loading …

Abstract

Need of industrial growth for developing country gives rapid acceleration in the field of technical research. Industries are very much aware of producing mechanical component with good surface quality without allowing a margin of error. Among the different challenges of industry, surface quality is the key factor now a day’s which can be improved by a novel after machining process known as burnishing process. This paper is mainly concerned with the effect of different process parameter on the surface roughness of aluminum alloy and the optimization of response measure. To achieve the goal of proposed work first pilot experiment is intended to ascertain the range of different parameters required for the experimental design methodology. Analysis of variance and signal to noise ratio are applied as statistical analysis to find out the significant control factor and optimize the level. The result shows the optimum set of process parameter having a value of 850 RPM spindle speed, 8 mm interference, 0.024 mm/rev feed and 4 no. of tool pass predict 0.010 µm surface roughness value which is having a greater agreement with the experimental value.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

  • über 102.000 Bücher
  • über 537 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Finance + Banking
  • Management + Führung
  • Marketing + Vertrieb
  • Maschinenbau + Werkstoffe
  • Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

  • über 67.000 Bücher
  • über 390 Zeitschriften

aus folgenden Fachgebieten:

  • Automobil + Motoren
  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Elektrotechnik + Elektronik
  • Energie + Nachhaltigkeit
  • Maschinenbau + Werkstoffe




 

Jetzt Wissensvorsprung sichern!

Springer Professional "Wirtschaft"

Online-Abonnement

Mit Springer Professional "Wirtschaft" erhalten Sie Zugriff auf:

  • über 67.000 Bücher
  • über 340 Zeitschriften

aus folgenden Fachgebieten:

  • Bauwesen + Immobilien
  • Business IT + Informatik
  • Finance + Banking
  • Management + Führung
  • Marketing + Vertrieb
  • Versicherung + Risiko




Jetzt Wissensvorsprung sichern!

Literatur
1.
Zurück zum Zitat ASTM Stand. B 209-96, In 1996 Annual Book of ASTM Standards, vol. 03.03, ASTM, West Conshohocken, PA (1996) ASTM Stand. B 209-96, In 1996 Annual Book of ASTM Standards, vol. 03.03, ASTM, West Conshohocken, PA (1996)
2.
Zurück zum Zitat Benardos, P.G., Vosniakos, G.C.: Prediction of surface roughness in CNC face milling using neural networks and Taguchi’s design of experiments. Robot. Comput. Integr. Manuf. 18(5), 343–354 (2002)CrossRef Benardos, P.G., Vosniakos, G.C.: Prediction of surface roughness in CNC face milling using neural networks and Taguchi’s design of experiments. Robot. Comput. Integr. Manuf. 18(5), 343–354 (2002)CrossRef
3.
Zurück zum Zitat Benardos, P.G., Vosniakos, G.C.: Predicting surface roughness in machining: a review. Int. J. Mach. Tools Manuf. 43(8), 833–844 (2003)CrossRef Benardos, P.G., Vosniakos, G.C.: Predicting surface roughness in machining: a review. Int. J. Mach. Tools Manuf. 43(8), 833–844 (2003)CrossRef
4.
Zurück zum Zitat Chen, C.H., Shiou, F.J.: Determination of optimal ball-burnishing parameters for plastic injection moulding steel. Int. J. Adv. Manuf. Technol. 21(3), 177–185 (2003)CrossRef Chen, C.H., Shiou, F.J.: Determination of optimal ball-burnishing parameters for plastic injection moulding steel. Int. J. Adv. Manuf. Technol. 21(3), 177–185 (2003)CrossRef
5.
Zurück zum Zitat El-Axir, M.H.: An investigation into roller burnishing. Int. J. Mach. Tools Manuf. 40(11), 1603–1617 (2000)CrossRef El-Axir, M.H.: An investigation into roller burnishing. Int. J. Mach. Tools Manuf. 40(11), 1603–1617 (2000)CrossRef
6.
Zurück zum Zitat El-Axir, M.H., El-Khabeery, M.M.: Influence of orthogonal burnishing parameters on surface characteristics for various materials. J. Mater. Process. Technol. 132(1), 82–89 (2003)CrossRef El-Axir, M.H., El-Khabeery, M.M.: Influence of orthogonal burnishing parameters on surface characteristics for various materials. J. Mater. Process. Technol. 132(1), 82–89 (2003)CrossRef
7.
Zurück zum Zitat El-Khabeery, M.M., El-Axir, M.H.: Experimental techniques for studying the effects of milling roller-burnishing parameters on surface integrity. Int. J. Mach. Tools Manuf. 41(12), 1705–1719 (2001)CrossRef El-Khabeery, M.M., El-Axir, M.H.: Experimental techniques for studying the effects of milling roller-burnishing parameters on surface integrity. Int. J. Mach. Tools Manuf. 41(12), 1705–1719 (2001)CrossRef
8.
Zurück zum Zitat El-Taweel, T.A., El-Axir, M.H.: Analysis and optimization of the ball burnishing process through the Taguchi technique. Int. J. Adv. Manuf. Technol. 41(3–4), 301–310 (2009)CrossRef El-Taweel, T.A., El-Axir, M.H.: Analysis and optimization of the ball burnishing process through the Taguchi technique. Int. J. Adv. Manuf. Technol. 41(3–4), 301–310 (2009)CrossRef
9.
Zurück zum Zitat Garg, R., Singh, H.: Optimisation of process parameters for gap current in wire electrical discharge machining. Int. J. Manuf. Technol. Manage. 25(1), 161–175 (2012) Garg, R., Singh, H.: Optimisation of process parameters for gap current in wire electrical discharge machining. Int. J. Manuf. Technol. Manage. 25(1), 161–175 (2012)
10.
Zurück zum Zitat Gharbi, F., Sghaier, S., Al-Fadhalah, K.J., Benameur, T.: Effect of ball burnishing process on the surface quality and microstructure properties of AISI 1010 steel plates. J. Mater. Eng. Perform. 20(6), 903–910 (2001)CrossRef Gharbi, F., Sghaier, S., Al-Fadhalah, K.J., Benameur, T.: Effect of ball burnishing process on the surface quality and microstructure properties of AISI 1010 steel plates. J. Mater. Eng. Perform. 20(6), 903–910 (2001)CrossRef
11.
Zurück zum Zitat Kiran, A., Nikunj, K., Disha, B.: Parametric optimization of process parameter for roller burnishing process. Int. J. Sci. Res. Dev. 1(4), 806–811 (2014) Kiran, A., Nikunj, K., Disha, B.: Parametric optimization of process parameter for roller burnishing process. Int. J. Sci. Res. Dev. 1(4), 806–811 (2014)
12.
Zurück zum Zitat Li, F.L., Xia, W., Zhou, Z.Y., Zhao, J., Tang, Z.Q.: Analytical prediction and experimental verification of surface roughness during the burnishing process. Int. J. Mach. Tools Manuf. 62, 67–75 (2012)CrossRef Li, F.L., Xia, W., Zhou, Z.Y., Zhao, J., Tang, Z.Q.: Analytical prediction and experimental verification of surface roughness during the burnishing process. Int. J. Mach. Tools Manuf. 62, 67–75 (2012)CrossRef
13.
Zurück zum Zitat Lin, Y.C., Yan, B.H., Huang, F.Y.: Surface improvement using a combination of electrical discharge machining with ball burnish machining based on the Taguchi method. Int. J. Adv. Manuf. Technol. 18(9), 673–682 (2001)MathSciNetCrossRef Lin, Y.C., Yan, B.H., Huang, F.Y.: Surface improvement using a combination of electrical discharge machining with ball burnish machining based on the Taguchi method. Int. J. Adv. Manuf. Technol. 18(9), 673–682 (2001)MathSciNetCrossRef
14.
Zurück zum Zitat Lin, C.L.: Use of the Taguchi method and grey relational analysis to optimize turning operations with multiple performance characteristics. Mater. Manuf. Process. 19(2), 209–220 (2004)CrossRef Lin, C.L.: Use of the Taguchi method and grey relational analysis to optimize turning operations with multiple performance characteristics. Mater. Manuf. Process. 19(2), 209–220 (2004)CrossRef
15.
Zurück zum Zitat Nemat, M., Lyons, A.C.: An investigation of the surface topography of ball burnished mild steel and aluminium. Int. J. Adv. Manuf. Technol. 16(7), 469–473 (2000)CrossRef Nemat, M., Lyons, A.C.: An investigation of the surface topography of ball burnished mild steel and aluminium. Int. J. Adv. Manuf. Technol. 16(7), 469–473 (2000)CrossRef
16.
Zurück zum Zitat Randjelovic, S., Tadic, B., Todorovic, P.M., Vukelic, D., Miloradovic, D., Radenkovic, M., Tsiafis, C.: Modelling of the ball burnishing process with a high-stiffness tool. Int. J. Adv. Manuf. Technol., 1–10 (2015) Randjelovic, S., Tadic, B., Todorovic, P.M., Vukelic, D., Miloradovic, D., Radenkovic, M., Tsiafis, C.: Modelling of the ball burnishing process with a high-stiffness tool. Int. J. Adv. Manuf. Technol., 1–10 (2015)
17.
Zurück zum Zitat Rao, D.S., Hebbar, H.S., Komaraiah, M., Kempaiah, U.N.: Investigations on the effect of ball burnishing parameters on surface hardness and wear resistance of HSLA dual-phase steels. Mater. Manuf. Process. 23(3), 295–302 (2008)CrossRef Rao, D.S., Hebbar, H.S., Komaraiah, M., Kempaiah, U.N.: Investigations on the effect of ball burnishing parameters on surface hardness and wear resistance of HSLA dual-phase steels. Mater. Manuf. Process. 23(3), 295–302 (2008)CrossRef
18.
Zurück zum Zitat Sarıkaya, M., Güllü, A.: Taguchi design and response surface methodology based analysis of machining parameters in CNC turning under MQL. J. Clean. Prod. 65, 604–616 (2014)CrossRef Sarıkaya, M., Güllü, A.: Taguchi design and response surface methodology based analysis of machining parameters in CNC turning under MQL. J. Clean. Prod. 65, 604–616 (2014)CrossRef
19.
Zurück zum Zitat Sastry, M.N.P., Devi, K.D., Reddy, K.M.: Analysis and optimization of machining process parameters using design of experiments. Ind. Eng. Lett. 2(9), 23–32 (2012) Sastry, M.N.P., Devi, K.D., Reddy, K.M.: Analysis and optimization of machining process parameters using design of experiments. Ind. Eng. Lett. 2(9), 23–32 (2012)
20.
Zurück zum Zitat Sathiya, P., Aravindan, S., Haq, A.N.: Optimization for friction welding parameters with multiple performance characteristics. Int. J. Mech. Mater. Des. 3(4), 309–318 (2006)CrossRef Sathiya, P., Aravindan, S., Haq, A.N.: Optimization for friction welding parameters with multiple performance characteristics. Int. J. Mech. Mater. Des. 3(4), 309–318 (2006)CrossRef
Metadaten
Titel
Implementation of Taguchi Method in the Optimization of Roller Burnishing Process Parameter for Surface Roughness
verfasst von
Kiran A. Patel
Pragnesh K. Brahmbhatt
Copyright-Jahr
2016
DOI
https://doi.org/10.1007/978-3-319-30927-9_19