nach oben

Journal of Materials Engineering and Performance

Erschienen in:

16.04.2019

Influence of Substrate Bias Voltage on Corrosion and Wear Behavior of Physical Vapor Deposition CrN Coatings

verfasst von: Khalil Aouadi, Brahim Tlili, Corinne Nouveau, Aurélien Besnard, Moez Chafra, Rania Souli

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 5/2019

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The objective of the present paper is to study the influence of the substrate bias voltage on the microstructure, composition, deposition rate, tribological and corrosion properties of CrN coatings obtained by DC magnetron sputtering on 90CrMoV8 steel and Si (100) substrates. The substrate bias voltage varied from 0 to − 700 V. The deposited films were characterized by SEM, XRD and potentiodynamic polarization. The wear behavior and coefficient of friction were determined and investigated after rotative tribometer tests. The results indicated that the substrate bias voltage considerably affected the intrinsic properties of the CrN films. Indeed, it significantly influenced the grain size and the root-mean-squared roughness which varied from 20 to 29 nm, and from 9 to 19 nm, respectively, when polarization changed from 0 to − 700 V. All the CrN coatings have a dense columnar structure and are well crystallized according to the XRD analyses. Nevertheless, it has been shown that the peaks intensity decreased by increasing the substrate bias voltage. By applying a substrate bias voltage, it was obvious that the friction behavior was enhanced, and the wear volume was decreased. Finally, the CrN coating obtained under a substrate bias voltage of − 500 V presented the best corrosion resistance and wear resistance probably due to its dense microstructure.

Vorheriger Artikel Electrochemical Investigations on AZ Series Magnesium Alloys as Anode Materials in a Sodium Chloride Solution

Nächster Artikel Effect of Ca and Sm Combined Addition on the Microstructure and Elevated-Temperature Mechanical Properties of Mg-6Al Alloys

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

A. Kusiak, J. Battaglia, and R. Marchal, Influence of CrN Coating in Wood Machining from Heat Flux Estimation in the Tool, Int. J. Therm. Sci., 2005, 44, p 289–301CrossRef

H.Y. Lee, J.G. Han, S.H. Baeg, and S.H. Yang, Structure and Properties of WC-CrAlN Superlattice Films by Cathodic Arc Ion Plating Process, Thin Solid Films, 2002, 421, p 414–420CrossRef

P. Gogolewski, J. Klimke, A. Krell, and P. Beer, Al₂O₃ Tools Towards Effective Machining of Wood-Based Materials, J. Mater. Proc. Technol., 2009, 209, p 2231–2236CrossRef

T. Polcar, N.M.G. Parreira, and R. Novák, Friction and Wear Behaviour of CrN Coating at Temperatures up to 500 °C, Surf. Coat. Technol., 2007, 201, p 5228–5235CrossRef

S. Inoue, F. Okada, and K. Koterazawa, CrN Films Deposited by RF Reactive Sputtering Using a Plasma Emission Monitoring Control, Vacuum, 2002, 66, p 227–231CrossRef

T. Hurkmans, D.B. Lewis, J.S. Brooks, and W.-D. Munz, Chromium Nitride Coatings Grown by Unbalanced Magnetron (UBM) and Combined Arc/Unbalanced Magnetron (ABSTM) Deposition Techniques, Surf. Coat. Technol., 1996, 87, p 192–199CrossRef

J.J. Lin, N. Zhang, W.D. Sproul, and J.J. Moore, A Comparison of the Oxidation Behavior of CrN Films Deposited Using Continuous DC, Pulsed DC and Modulated Pulsed Power Magnetron Sputtering, Surf. Coat. Technol., 2012, 206, p 3283–3290CrossRef

J. Lin, J.J. Moore, W.D. Sproul, B. Mishra, Z. Wu, and J. Wang, The Structure and Properties of Chromium Nitride Coatings Deposited Using DC, Pulsed DC and Modulated Pulse Power Magnetron Sputtering, Surf. Coat. Technol., 2010, 204, p 2230–2239CrossRef

Z.B. Zhao, Z.U. Rek, S.M. Yalisove, and J.C. Bilello, Phase Formation and Structure of Magnetron Sputtered Chromium Nitride Films: In Situ and Ex Situ Studies, Surf. Coat. Technol., 2004, 185, p 329–339CrossRef

10.

E. Broszeit, C. Friedrich, and G. Berg, Deposition, Properties and Applications of PVD CrN Coatings, Surf. Coat. Technol., 1999, 115, p 9–16CrossRef

11.

C. Nouveau, E. Jorand, C. Decès-Petit, C. Labidi, and M. Djouadi, Influence of Carbide Substrates on Tribological Properties of Chromium and Chromium Nitride Coatings: Application to Wood Machining, Wear, 2005, 258, p 157–165CrossRef

12.

M. Oden, C. Ericsson, G. Hakansson, and H. Ljungcrantz, Microstructure and Mechanical Behavior of Arc-Evaporated Cr-N Coatings, Surf. Coat. Technol., 1999, 114, p 39–51CrossRef

13.

X.S. Wan, S.S. Zhao, Y. Yang, J. Gong, and C. Sun, Effects of Nitrogen Pressure and Pulse Bias Voltage on the Properties of Cr-N Coatings Deposited by Arc Ion Plating, Surf. Coat. Technol., 2010, 204, p 1800–1810CrossRef

14.

B. Warcholinski and A. Gilewicz, Effect of Substrate Bias Voltage on the Properties of CrCN and CrN Coatings Deposited by Cathodic Arc Evaporation, Vacuum, 2013, 90, p 145–150CrossRef

15.

K. Valleti, A. Jyothirmayi, M. Ramakrishna, and S.V. Joshi, Influence of Substrate Temperature and Bias Voltage on Properties of Chromium Nitride Thin Films Deposited by Cylindrical Cathodic Arc Deposition, J. Vac. Sci. Technol., A, 2011, 29(5), p 051515CrossRef

16.

C. Luo, H. Zhang, J. Shang, and S. Duo, Effect of Bias Voltage on Microstructure and Mechanical Properties of CrN Coatings Prepared by Single Target Magnetron Sputtering, Key Eng. Mater., 2016, 697, p 777–780CrossRef

17.

Q. Kong, L. Ji, H. Li, X. Liu, Y. Wang, J. Chen, and H. Zhou, Influence of Substrate Bias Voltage on the Microstructure and Residual Stress of CrN Films Deposited by Medium Frequency Magnetron Sputtering, Mater. Sci. Eng., 2011, 176, p 850–854CrossRef

18.

E. Eser, R.E. Ogilvie, and K.A. Taylor, The Effect of Bias on DC and RF Sputtering WCCo Coating, Thin Solid Films, 1980, 67, p 265–277CrossRef

19.

H.-W. Chang, P.-K. Huang, J.-W. Yeh, A. Davison, C.-H. Tsau, and C.-C. Yangh, Influence of Substrate Bias, Deposition Temperature and Post-deposition Annealing on the Structure and Properties of Multi-principal-component (AlCrMoSiTi)N Coatings, Surf. Coat. Technol., 2008, 202, p 3360–3366CrossRef

20.

C. Chang and C. Huang, Effect of Bias Voltage on Microstructure, Mechanical and Wear Properties of AlSiN Coatings Deposited by Cathodic Arc Evaporation, Thin Solid Films, 2011, 519, p 4923–4927CrossRef

21.

Z. Wang, D. Zhang, P. Ke, X. Liu, and A. Wang, Influence of Substrate Negative Bias on Structure and Properties of TiN Coatings Prepared by Hybrid HIPIMS Method, J. Mater. Sci. Technol., 2015, 31, p 37–42CrossRef

22.

M.R. Ardigo, M. Ahmed, and A. Besnard, Stoney Formula: Investigation of Curvature Measurements by Optical Profilometer, Adv. Mater. Res., 2014, 996, p 361–366CrossRef

23.

K. Rahmoun, A. Iost, V. Keryvin, G. Guillemot, and N.E.C. Sari, A Multilayer Model for Describing Hardness Variations of Aged Porous Silicon Low-Dielectric-Constant Thin Films, Thin Solid Films, 2009, 518, p 213–221CrossRef

24.

V.D. Ovcharenko, A.S. Kuprin, G.N. Tolmachova, I.V. Kolodiy, A. Gilewicz, O. Lupicka, J. Rochowicz, and B. Warcholinski, Deposition of Chromium Nitride Coatings Using Vacuum Arc Plasma in Increased Negative Substrate Bias Voltage, Vaccum, 2015, 117, p 27–34CrossRef

25.

D. Tsai, S. Liang, Z. Chang, T. Lin, M. Shiao, and F. Shieu, Effects of Substrate Bias on Structure and Mechanical Properties of (TiVCrZrHf) N Coatings, Surf. Coat. Technol., 2012, 207, p 293–299CrossRef

26.

A.J. Detor, A.M. Hodge, E. Chason, Y. Wang, H. Xu, M. Conyers, A. Nikroo, and A. Hamza, Stress and Microstructure Evolution in Thick Sputtered Films, Acta Mater., 2009, 57, p 2055–2065CrossRef

27.

Y. Lv, L. Ji, X. Liu, H. Li, H. Zhou, and J. Chen, Influence of Substrate Bias Voltage on Structure and Properties of the CrAlN Films Deposited by Unbalanced Magnetron Sputtering, Appl. Surf. Sci., 2012, 258, p 3864–3870CrossRef

28.

Q. Wang, S. Kwon, and K. Kim, Formation of Nanocrystalline Microstructure in Arc Ion Plated CrN Films, Trans. Nonferr. Met. Soc. China, 2011, 21, p 73–77CrossRef

29.

C. Hsu, K. Chen, Z. Lin, C. Su, and C. Lin, Bias Effects on the Tribological Behavior of Cathodic Arc Evaporated CrTiAlN Coatings on AISI, 304 Stainless Steel, Thin Solid Films, 2010, 518, p 3825–3829CrossRef

30.

J.J. Olaya, S.E. Rodil, S. Muhl, and E. Sanchez, Comparative Study of Chromium Nitride Coatings Deposited by Unbalanced and Balanced Magnetron Sputtering, Thin Solid Films, 2005, 474, p 119–126CrossRef

31.

C.V. Thompson and R. Carel, Stress and Grain Growth in Thin Films, J. Mech. Phys. Solids, 1996, 44, p 657–673CrossRef

32.

Q. Ma, L. Li, Y. Xu, J. Gu, L. Wang, and Y. Xu, Effect of Bias Voltage on TiAlSiN Nanocomposite Coatings Deposited by HiPIMS, Appl. Surf. Sci., 2017, 392, p 826–833CrossRef

33.

E. Forniés, R.E. Galindo, O. Sánchez, and J.M. Albella, Growth of CrN_x Films by DC Reactive Magnetron Sputtering at Constant N₂/Ar Gas Flow, Surf. Coat. Technol., 2006, 200, p 6047–6053CrossRef

34.

G.P. Zhang, G.J. Gao, X.Q. Wang, G.H. Lv, L. Zhou, H. Chen, H. Pang, and S.Z. Yang, Influence of Pulsed Substrate Bias on the Structure and Properties of Ti-Al-N Films Deposited by Cathodic Vacuum Arc, Appl. Surf. Sci., 2012, 258, p 7274–7279CrossRef

35.

T. Lin, L. Wang, X. Wang, Y. Zhang, and Y. Yu, Influence of Bias Voltage on Microstructure and Phase Transition Properties of VO₂ Thin Film Synthesized by HiPIMS, Surf. Coat. Technol., 2016, 305, p 110–115CrossRef

36.

S.G. Wang, E.K. Tian, and C.W. Lung, Surface Energy of Arbitrary Crystal Plane of bcc and fcc Metals, J. Phys. Chem. Solids, 2000, 61, p 1295–1300CrossRef

37.

Y.X. Wang, S. Zhang, J.-W. Lee, W.S. Lew, and B. Li, Influence of Bias Voltage on the Hardness and Toughness of CrAlN Coatings via Magnetron Sputtering, Surf. Coat. Technol., 2012, 206, p 5103–5107CrossRef

38.

J. Pelleg, L.Z. Zevin, and S. Lungo, Reactive-Sputter-Deposited TiN Films on Glass Substrates, Thin Solid Films, 1991, 197, p 117–128CrossRef

39.

F. Lomello, F. Sanchette, F. Schuster, M. Tabarant, and A. Billard, Influence of Bias Voltage on Properties of AlCrN Coatings Prepared by Cathodic Arc Deposition, Surf. Coat. Technol., 2013, 24, p 77–81CrossRef

40.

F. Zhou, K. Chen, M. Wang, X. Xu, H. Meng, M. Yu, and Z. Dai, Friction and Wear Properties of CrN Coatings Sliding Against Si₃N₄ Balls in Water and Air, Wear, 2008, 65, p 1029–1037CrossRef

41.

Y.N. Kok, P.E. Hovsepian, Q. Luo, D.B. Lewis, J.G. Wen, and I. Petrov, Influence of the Bias Voltage on the Structure and the Tribological Performance of Nanoscale Multilayer C/Cr PVD Coatings, Thin Solid Films, 2005, 475, p 219–226CrossRef

42.

J. Romero, M.A. Gómez, J. Esteve, F. Montalà, L. Carreras, M. Grifol, and A. Lousa, CrAlN Coatings Deposited by Cathodic Arc Evaporation at Different Substrate Bias, Thin Solid Films, 2006, 515, p 113–117CrossRef

43.

B. Biswas, Y. Purandare, I. Khan, and P.E. Hovsepian, Effect of Substrate Bias Voltage on Defect Generation and Their Influence on Corrosion and Tribological Properties of HIPIMS Deposited CrN/NbN Coatings, Surf. Coat. Technol., 2018, 344, p 383–393CrossRef

44.

J.C. Ding, Q.M. Wang, Z.R. Liu, S. Jeong, T.F. Zhang, and K.H. Kim, Influence of Bias Voltage on the Microstructure, Mechanical and Corrosion Properties of AlSiN Films Deposited by HiPIMS Technique, J. Alloys Compd., 2019, 772, p 112–121CrossRef

45.

L. Bait, L. Azzouz, N. Madaoui, and N. Saoula, Influence of Substrate Bias Voltage on the Properties Of TiO₂ Deposited by Radio-Frequency Magnetron Sputtering on 304L for Biomaterials Applications, Appl. Surf. Sci., 2017, 395, p 72–77CrossRef

46.

D. Jianxin, W. Fengfang, L. Yunsong, X. Youqiang, and L. Shipeng, Erosion Wear of CrN, TiN, CrAlN, and TiAlN PVD Nitride Coatings, Int. J. Refract. Met. Hard Mater., 2012, 35, p 10–16CrossRef

47.

C. He, J. Zhang, G. Ma, Z. Du, J. Wang, and D. Zhao, Influence of Bias Voltage on Structure, Mechanical and Corrosion Properties of Reactively Sputtered Nanocrystalline TiN Films, J. Iron Steel Res. Inter., 2017, 24, p 1223–1230CrossRef

48.

S.G. Hong, S.H. Kwon, S.W. Kang, and K.H. Kim, Influence of Substrate Bias Voltage on Structure and Properties of Cr-Mo-Si-N Coatings Prepared by a Hybrid Coating System, Surf. Coat. Technol., 2008, 203, p 624–627CrossRef

49.

N. Liu, L. Dong, X. Li, D. Li, R. Wan, and H. Gu, Controllable Substrate Bias Voltages Effectively Tailoring Nanocomposite Nb-B-Al-O Film Properties, J. Alloys Compd., 2015, 636, p 363–367CrossRef

50.

H. Hsueh, W. Shen, M. Tsai, and J. Yeh, Effect of Nitrogen Content and Substrate Bias on Mechanical and Corrosion Properties of High-Entropy Films (AlCrSiTiZr) _100−xN_x, Surf. Coat. Technol., 2012, 206, p 4106–4112CrossRef

51.

M. Flores, L. Huerta, R. Escamilla, E. Andrade, and S. Muhl, Effect of Substrate Bias Voltage on Corrosion of TiN/Ti Multilayers Deposited by Magnetron Sputtering, Appl. Surf. Sci., 2007, 253, p 7192–7196CrossRef

Titel: Influence of Substrate Bias Voltage on Corrosion and Wear Behavior of Physical Vapor Deposition CrN Coatings
verfasst von: Khalil Aouadi
Brahim Tlili
Corinne Nouveau
Aurélien Besnard
Moez Chafra
Rania Souli
Publikationsdatum: 16.04.2019
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 5/2019
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-019-04033-y

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 5/2019

Effect of Tempering Temperature on the Precipitation Behavior and Mechanical Properties of a Martensite Ferritic Steel

Effects of Laser Fluence on Microstructure and Bonding Characteristics of Wideband Laser-Deposited Nickel Composite Coatings

Experimental Study on the Porosity of Electron Beam Melting-Manufactured Ti6Al4V

Effect of Dual-Phase Heat Treatment on Microstructure and Mechanical Properties of S135 High-Strength Drill Pipe Steel

Microstructure and Properties of Mn-Cu-Based Damping Alloys Prepared by Ball Milling and Hot-Press Sintering

Microstructural Stability During Creep Exposure of 9Cr-1Mo Steel Treated at Different Normalization Temperatures

Premium Partner

Marktübersichten