nach oben

Erschienen in:

2018 | OriginalPaper | Buchkapitel

6. Mechanical Characterization of Epoxy – Scrap Rubber Based Composites Reinforced with Alumina Fibers

verfasst von : A. B. Irez, E. Bayraktar, I. Miskioglu

Erschienen in: Mechanics of Composite and Multi-functional Materials, Volume 6

Verlag: Springer International Publishing

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Recently, encouraged by the idea of sustainable development, the emissions of CO₂ have become a very prominent issue to be solved. As a consequence, in the automotive and aeronautic industries, the reduction of weight has become a major issue and needs to be addressed for all possible structures in the vehicle. Therefore, some metallic parts are being replaced by polymer based composites. For this to happen, the feasibility of using these composites has to be examined properly in terms of their mechanical and energetic properties. Epoxy – rubber based composites reinforced with ceramics are studied by several researchers. However, addition of scrap rubber to the matrix and alumina fibers (Al₂O₃) as a reinforcement introduces a novelty in this area. Since, using of scrap rubber has positive outcomes in economical and structural perspectives such as revaluation of scraps and compensating the brittleness of epoxy. Also, due to its favorable structural characteristics such as interlocking properties of fibers, addition of alumina fibers ensures desired mechanical properties in case of a homogeneous distribution. This paper is focused on the design of epoxy – fresh scrap rubber matrix reinforced with different ratios of alumina fibers. The mechanical and some physical properties of these composite systems were studied in this research. Mechanical properties were evaluated by means of drop weight tests, three-point bending tests and nanoindentation technics. Scanning electron microscope (SEM) was used to observe fracture surfaces and the microstructure. After all, UV degradation of the material was observed by electron microscopy.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Vorheriges Kapitel Mechanical Characterization of Epoxy – Scrap Rubber Based Composites Reinforced with Nano Graphene

Nächstes Kapitel Scaled Composite I-Beams for Subcomponent Testing of Wind Turbine Blades: An Experimental Study

McGrath, L.M., et al.: Investigation of the thermal, mechanical, and fracture properties of alumina–epoxy composites. Polymer. 49(4), 999–1014 (2008)CrossRef

Zaimova, D, Bayraktar, E, Katundi, D, Dishovsky, N.: Design of new elastomeric composites used in manufacturing engineering. In: 14th International Materials Symposium–IMSP, pp. 10–12. Denizli (2012)

Shaw, S.J.: Rubber modified epoxy resins. In: Collyer, A.A. (ed.) Rubber Toughened Engineering Plastics, pp. 165–209. Chapman & Hall, London (1994)CrossRef

Sultan, J.N., McGarry, F.J.: Effect of rubber particle size on deformation mechanisms in glassy epoxy. Polym. Eng. Sci. 13, 29–34 (1973)CrossRef

Manzione, L.T., Gillham, J.K.: Rubber-modified epoxies. I. transitions and morphology. J. Appl. Polym. Sci. 26, 889–905 (1981)CrossRef

Nakamura, Y., Yamaguchi, M., Okubo, M., Matsumoto, T.: Effects of particle size on mechanical and impact properties of epoxy resin filled with spherical silica. J. Appl. Polym. Sci. 45(7), 1281–1289 (1992)CrossRef

Okazaki, M., Murota, M., Kawaguchi, Y., Tsubokawa, N.: Curing of epoxy resin by ultrafine silica modified by grafting of hyperbranched polyamidoamine using dendrimer synthesis methodology. J. Appl. Polym. Sci. 80(4), 573–579 (2001)CrossRef

Wetzel, B., Haupert, F., Zhang, M.Q.: Epoxy nanocomposites with high mechanical and tribological performance. Compos. Sci. Technol. 63(14), 2055–2067 (2003)CrossRef

Zee, R.H., Huang, Y.H., Chen, J.J., Jang, B.Z.: Properties and processing characteristics of dielectric-filled epoxy resins. Polym. Compos. 10(4), 205–214 (1989)CrossRef

10.

Jin Kim, D., Hyun Kang, P., Chang Nho, Y.: Characterization of mechanical properties of γAl₂O₃ dispersed epoxy resin cured by γ-ray radiation. J. Appl. Polym. Sci. 91, 1898–1903 (2004)CrossRef

11.

Arayasantiparb, D., McKnight, S., Libera, M.: Compositional variation within the epoxy/adherend interphase. J. Adhes. Sci. Technol. 15(12), 1463–1484 (2001)

12.

Nielsen, L.E., Landel, R.F.: Mechanical Properties of Polymers and Composites, 2nd edn. Marcel Dekker, Inc, New York (1994)

13.

Rothon, R. (ed.): Particulate-Filled Polymer Composites. Longman Scientific and Technical, London (1995)

14.

Rothon, R.N.: Mineral fillers in thermoplastics: filler manufacture and characterisation. Adv. Polym. Sci. 139, 67–107 (1999)CrossRef

15.

Zhang, Z., Wong, C.P.: Double-layer no-flow underfill materials and process. IEEE Trans. Adv. Packag. 26(2), 199–205 (2003)CrossRef

16.

Madenci, E., Shkarayev, S., Mahajan, R.: Potential failure sites in a flip-chip package with and without underfill. Trans ASME J Elect Pack. 120(4), 336–341 (1998)CrossRef

17.

Wu, T.Y., Tsukada, Y., Chen, W.T.: Materials and mechanics issues in flip-chip organic packaging. Proc Electron. Comp. Technol. Conf. 46, 524–534 (1996)

18.

Vo, H.T., Todd, M., Shi, F.G., Shapiro, A.A., Edwards, M.: Towards model-based engineering of underfill materials: CTE modeling. Microelectron. J. 32(4), 331–338 (2001)CrossRef

19.

Craig, R.G. (ed.): Restorative Dental Materials, 10th edn. Mosby-Year Book, Inc, St. Louis, Springer Cham Heidelberg New York Dordrecht London (1997)

20.

Stannard, J.G.: Materials in Dentistry, 2nd edn. Denali Pub, Hanover (1988)

21.

Babbington, D.A., Enos, J., Cox, J.M.: Barron J. Mod Plast. 64(8), 72, 74, 76 (1987)

22.

Mirjalili, F., Mohamad, H., Chuah, L.: Preparation of nano-scale α-Al2O3 powder by the sol–gel method. Ceram-Silikáty. 55, 378–383 (2011)

23.

Amirshaghaghi, A., Kokabi, M.: Tailoring size of α-Al2O3 nanopowders via polymeric gel–net method. Iran. Polym. J. 19, 615–624 (2010)

24.

Zhang, Z., Lei, H.: Preparation of α-alumina/polymethacrylic acid composite abrasive and its CMP performance on glass substrate. Microelectron. Eng. 85, 714–720 (2008)CrossRef

25.

Williams, J.G.: Fracture Mechanics of Polymers. Halsted Press, New York (1984)

26.

Bayraktar, E., Zaimova, D., Tan, M.-J., Miskioglu, I.: A preliminary study on an epoxy-rubber matrix with different reinforcements, In: G.P. Tandon (eds.) Experimental Mechanics of Composite, Hybrid, and Multifunctional Materials, vol. 6, no. 7, pp. 1–13. Springer Publication Springer link, (2014)

27.

Asaka, K., Ishihara, C.: Technical trends in soft magnetic parts and materials. Hitachi Powdered Metals Technical Report 420053 (2005)

28.

Zaimova, D., Bayraktar, E., Miskioglu, I., Katundi, D., Hamouche, Z.: Manufacturing and damage analysis of filler reinforced epoxy based composites. Int J Mat Prod Technol. 48(1–4): 47–65. Inter Science (ed.), 0268-1900/1741-5209 (2014)

29.

Zaimova, D., Bayraktar, E., Miskioglu, I., Dishovsky, N.: Wear resistance of elastomeric based composites by continuous multi-cycle indentation used in manufacturing engineering. Adv. Mat. Res. 939(1):106–113. Trans Tech Publications (ed.), Switzerland (2014)

30.

Zaimova, D., Bayraktar, E., Tan, M. J., Miskioglu, I.: Processing of epoxy-nickel matrix composites reinforced with aluminum and waste elastomers. Adv. Mat. Res. 939(1): 98–105. Trans Tech Publications (ed.), Switzerland (2014)

31.

Zaimova, D., et al.: Manufacturing and damage analysis of epoxy resin-reinforced scrap rubber composites for aeronautical applications. Experimental mechanics of composite, hybrid, and multifunctional materials, vol. 6, pp. 65–76. Springer International Publishing, (2014)

Titel: Mechanical Characterization of Epoxy – Scrap Rubber Based Composites Reinforced with Alumina Fibers
verfasst von: A. B. Irez
E. Bayraktar
I. Miskioglu
Verlag: Springer International Publishing
Buch: Mechanics of Composite and Multi-functional Materials, Volume 6
Print ISBN: 978-3-319-63407-4

Electronic ISBN: 978-3-319-63408-1

Copyright-Jahr: 2018
DOI: https://doi.org/10.1007/978-3-319-63408-1_6

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht