Abstract
This paper deals with the fracture performance of injection moulded long glass fibre composites based on polybutylene terephthalate (PBT) and polypropylene (PP) matrices. The tensile behaviour of these composites is analysed using the shear lag theory taking into consideration the interfacial shear strength, fibre length distribution and fibre orientation in the mouldings. The fracture performance is investigated using the post yield fracture mechanics approach. The crack growth resistance of the PP and PBT long fibre composite was found to increase with increasing fibre volume content up to 35%. Above 35% a plateau in the fracture performance was observed. A combination of high fibre degradation and a change in the fibre orientation pattern of the moulded pieces is found to be responsible for the plateau region in the performance of the high concentration system. In fact, the dependence of the maximum crack growth resistance of the composites on fibre length and fibre orientation is also controlled by testing temperature. The competition between fibre-induced matrix deformation and the fibre pull-out determines the ability of the composites to resist crack propagation.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
M. G. BADER and W. H. BOWYER, Composites 4 (1973) 150.
D. A. CIANELLI, J. E. TRAVIS and R. S. BAILEY, Plast. Technol. 34 (1988) 83.
W. H. BOWYER, and M. G. BADER, J. Mater. Sci. 7 (1972) 1315.
M. G. BADER and J. F. COLLINS, Proc. 4th Int. Conf. Compos. Mater., ICCM-IV, edited by T. Hayashi, K. Kawata and S. Umekawa (Tokyo, 1982) p. 1067.
P. T. CURTIS, M. G. BADER and J. E. BAILEY, J. Mater. Sci. 13 (1978) 377.
F. RAMSTEINER and R. THEYSON, Composites 10 (1979) 111.
M. W. DARLINGTON, B. K. GLADWELL and G. R. SMITH, Polymer 18 (1977) 1269.
T. VU-KHANH, B. SANSCHAGRIN and B. FISA, Polym. Compos. 6 (1985) 249.
J. DENAULT and T. VU-KHANH, ibid. 9 (1988) 360.
T. VU-KHANH and B. FISA, ibid. 7 (1986) 375.
T. VU-KHANH and B. FISA, ibid. 7 (1986) 219.
T. VU-KHANH, J. Thermoplast. Compos. Mater. 4 (1991) 46.
T. VU-KHANH and B. FISA, Theoretical and Appl. Fract. Mech. 13 (1990) 11.
T. VU-KHANH, Proc. Fifth Techn. Conf. of the American Society for Composites (Technomic Publishing, East Lansing, MI, 1990) p. 309.
J. DENAULT, T. VU-KHANH and B. FOSTER, Polym. Compos. 10 (1989) 313.
B. SCHIMD, Kunstst Plast. 79 (1989) 39.
R. BAILEY and H. KRAFT, Intern. Polym. Process. 2 (1987) 94.
R. BAILEY, Proc. SPE 36th Annual Techn. Conf. (ANTEC '90, Dallas, TX, 1990) p. 1339.
T. VU-KHANH, J. DENAULT, P. HABIB and A. LOW, Compos. Sci. Technol. 40 (1991) 423.
J. KARGER-KOCSIS and K. FRIEDRICH, ibid. 32 (1988) 293.
D. E. SPAHR, K. FRIEDRICH, J. M. SCHULTZ, and R. S. BAILEY, J. Mater. Sci. 25 (1990) 4427.
B. FISA, Polym. Compos. 6 (1985) 232.
E-399 Standard Test Method for Plane Strain Fracture Toughness of Metallic Material, Annual Book of ASTM Standards (1983).
K. FRIEDRICH, Plast. Rubber Process. Appl. 3 (1983) 255.
Idem, Compos. Sci. Technol. 22 (1985) 43.
J. KARGER-KOCSIS and K. FRIEDRICH, Composites 19 (1988) 105.
K. FRIEDRICH, R. WALTER, H. VOSS and J. KARGERKOCSIS, ibid. 17 (1986) 205.
M. W. DARLINGTON, P. L. McGINLEY and G. R. SMITH, J. Mater. Sci 11 (1976) 877.
P. F. BRIGHT, R. J. CROWSON and M. J. FOLKES, ibid. 13 (1978) 2497.
P. F. BRIGHT and M. W. DARLINGTON, Plast. Rubb. Process. Appl. 1 (1981) 139.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Vu-Khanh, T., Denault, J. Fracture behaviour of long fibre reinforced thermoplastics. JOURNAL OF MATERIALS SCIENCE 29, 5732–5738 (1994). https://doi.org/10.1007/BF00349973
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF00349973