Abstract
The indentation technique for determining material toughness is applied to spinel and yttria-stabilized zirconia plasma-sprayed coatings in this investigation. Fracture toughness of the coatings ranged from 1.9 to 3.4 MPa√m for spinel and 2.0 to 3.3 MPa√m for yttria-stabilized zirconia. These results are in good agreement with those obtained by other experimenters for bulk materials.
Similar content being viewed by others
References
A.G. Evans, Fracture Mechanics Deformation,Fracture Mechanics of Ceramics, Vol 1, R.C. Bradt, D.P.H. Hasselman, and F.F. Lange, Ed., Plenum Press, 1979, p 17–49.
A.G. Evans, Fracture Toughness: The Rule of Indentation Techniques,Proceedings of the 11 th National Symposium on Fracture Mechanics of ASTM, STP 678, Part II, ASTM, 1979, p 112–134.
J. Lanford, Indentation Microfracture in the Palmqvist Crack Regime: Implication for Fracture Toughness Evaluation by the Indentation Method,J. Mater. Sci. Lett., Vol 1, 1982, p 493–495.
K. Niihara, R. Morena, and D.P.H. Hasselman, Evaluation of Fracture Toughness of Brittle Solids by the Indentation Method with Low Crack-to-indent Ratios,J. Mater. Sci. Lett., Vol 1, 1982, p 13–16.
B.R. Lawn and D.B. Marshall, Residual Stress Effects in Failure from Flaws,J. Am. Ceram. Soc, Vol 62 (No. 1–2), 1979, p 106–108.
D.K. Shetty, G. Wright, P.N. Mincer, and A.H. Clauer, Indentation Fracture of WC-Co Cermets,J. Mater. Sci., Vol 20, 1985, p 1873–1882.
B.R. Lawn, A.G. Evans, and D.B. Marshall, Elastic/Plastic Indentation Damage in Ceramics: The Median/Radial Crack System,J. Am. Ceram. Soc, Vol 63 (No. 9–10), 1980, p 574–581.
K. Niihara, A Fracture Mechanics Analysis of Indentation Induced Palmqvist Crack in Ceramics,J. Mater. Sci. Lett., Vol 2, 1983, p 221–223.
A.G. Evans, Impact Damage in Ceramics,Fracture Mechanics of Ceramics, Vol 3, R.G. Bradt, D.P.H. Hasselman, and F.F. Lange, Ed., Plenum Press, 1978, p 301–331.
R.H. Marion, Use of Indentation Fracture to Determine Fracture Toughness, Fracture Mechanics Applied to Brittle Materials,Proceedings of the 11 th National Symposium on Fracture Mechanics of ASTM, STP 678, Part II, ASTM, 1979, p 112–134.
A.G. Evans and E.A. Charles, Fracture Toughness Determination by Indentation,J. Am. Ceram. Soc, Vol 59 (No. 7–8), 1976, p 371–372.
B.R. Lawn and E.R. Fuller, Equilibrium Penny-Like Cracks in Indentation Fracture,J. Mater. Sci., Vol 10, 1975, p 2016–20240.
G.R. Anstis, P. Chantikul, B.R. Lawn, and D.B. Marshall, A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness: I. Direct Crack Measurements,J. Am. Ceram. Soc, Vol 64 (No. 9), 1981, p 533–538.
D.C. Zipperian, Preparation of Ceramics Materials for Surface Characterization,Ceram. Bull., Vol 68 (No. 6), 1989, p 1196–1201.
B.R. Lawn, D.B. Marshall, and P. Chantikul, Mechanics of Strength-Degrading Contact Flaws in Silicon,J. Mater. Sci., Vol 16, 1981, p 1769–1775.
T.K. Gupta, Role of Stress-Induced Phase Transformation in Enhancing Strength and Toughness of Zirconia Ceramics,Fracture Mechanics of Ceramics, Vol 4, Plenum Press, 1977, p 877–889.
R.W. Rice, S.W. Freiman, R.C. Pohanka, J.J. Mecholsky, Jr., and C.Cm. Wu, Microstructural Dependence of Fracture Mechanics Parameters in Ceramics,Fracture Mechanics of Ceramics, Vol 4, Plenum Press, 1977, p 849–876.
P. Ostojic and R. McPherson, Indentation Toughness Testing of Plasma Sprayed Coatings,Mater. Forum, Vol 10 (No. 4), 1987, p 247–255.
J. Boussinesq,Theory of Elasticity, S.P. Timoshenko and J.N. Goodier, Ed., McGraw-Hill, 1969, p 398–402.
B.R. Lawn and M.V. Swain, Microfracture Beneath Point Indentation in Brittle Solids,J. Mater. Sci., Vol 10, 1975, p 113–122.
D.J. Green, P.S. Nicholson, and J.D. Embury, Fracture Toughness of Partially Stabilized ZrO2 in the System CaO-ZrO2,J. Am. Ceram. Soc, Vol 56 (No. 12), 1973, p 619–623.
R.L. Stewart and R.C. Bradt, Fracture Toughness of Single Crystals of MgAl2O4,J. Mater. Sci., Vol 15, 1985, p 67–72.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Beshish, G.K., Florey, C.W., Worzala, F.J. et al. Fracture toughness of thermal spray ceramic coatings determined by the indentation technique. JTST 2, 35–38 (1993). https://doi.org/10.1007/BF02647421
Issue Date:
DOI: https://doi.org/10.1007/BF02647421