Abstract
The objective of this study is to investigate numerically the flow characteristics of falling film on horizontal circular tubes. Numerical simulations are performed using FLUENT for 2D configurations with one and two cylinders. The volume of fluid method is used to track the motion of liquid falling film and the gas-liquid interface. The effect of flow characteristics on heat and transfer coefficient may be remarkable, although it has been neglected in previous studies. The velocity distribution and the film thickness characteristics on the top tube, some special flow characteristics on the bottom tube, intertube flow modes and effect of liquid feeder height on flow characteristics have been studied. Our simulations indicate that 1) the velocity distributions of the upper and lower parts of the tube are not strictly symmetric and nonuniform, 2) the film thickness depends on flow rate and angular distributions, 3) the flow characteristics of the top tube are different from those of the bottom tube, 4) three principal and two intermediate transition modes are distinguished, and 5) the liquid feed height plays an important role on the formation of falling film. The numerical results are in a good agreement with the theoretical values by the Nusselt model and the reported results.
Similar content being viewed by others
References
Nusselt W. Die Oberflächenkondensation des Wasser-dampfes. Zeitschr Ver Deut Ing, 1916, 60(27): 569–575
Adams FW, Broughton G, Conn A L. A horizontal film-type cooler: film coefficients of heat transmissions. Industrial & Engineering Chemistry, 1936, 28(5): 537–541
Kocamustafaogulari G, Chen I Y. Falling film heat transfer analysis on a bank of horizontal tube evaporator. AIChE Journal. American Institute of Chemical Engineers, 1988, 34(9): 1539–1549
Rogers J T, Goindi S S. Experimental laminar falling film heat transfer coefficient on a large diameter horizontal tube. Canadian Journal of Chemical Engineering, 1989, 67(4): 560–568
Mitrovic J. Influence of tube spacing and flow rate on heat transfer from a horizontal tube to a falling film. International Heat Transfer Conference San Francisco, 1986, 4: 1949–1956
Mohamed A M I. Flow behavior of liquid falling film on a horizontal rotating tube. Experimental Thermal and Fluid Science, 2007, 31(4): 325–332
Chen C I, Chen C K, Yang Y T. Perturbation analysis to the nonlinear stability characterization of thin condensate falling film on the outer surface of a rotating vertical cylinder. International Journal of Heat and Mass Transfer, 2004, 47(8–9): 1937–1951
Bandelier P. Improvement of multifunctional heat exchangers applied in industrial processes. Applied Thermal Engineering, 1997, 17(8–10): 777–788
Hari S, Takagi T, Tanaka K, Higashiya T. Turbulent heat transfer to the flow in a concerntric annulus with a rotating innner cylinder. Journal of Flow Visualization Society Japan, 1986, 3: 895–901
Hu X, Jacobi A M. The intertube falling film part1-flow characteristics, mode transitions and hysteresis. ASME Journal of Heat Transfer, 1996, 118(3): 616–625
Jafar F, Thorpe G, Turan O F. Liquid film falling on horizontal circular cylinders. 16th Australasian Fluid Mechanics Conference, 2007, 2–7: 1193–1199
Gao D, Morley N B, Dhir V. Numerical simulation of wavy falling film flow using VOF method. Journal of Computational Physics, 2003, 192(2): 624–642
Gu F, Liu C J, Yuan X G, Yu G C. CFD simulation of liquid film flow on inlined plates. Chemical Engineering & Technology, 2004, 27(10): 1099–1104
Ouldhadda D, Idrissi A I, Asbik M. Heat transfer in non-Newtonion falling liquid film on a horizontal circular cylinder. Heat and Mass Transfer, 2002, 38(7–8): 713–721
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Sun, F., Xu, S. & Gao, Y. Numerical simulation of liquid falling film on horizontal circular tubes. Front. Chem. Sci. Eng. 6, 322–328 (2012). https://doi.org/10.1007/s11705-012-1296-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11705-012-1296-z