Skip to main content
SpringerLink
Log in

Fusion boundary microstructure evolution associated with embrittlement of Ni–base alloy overlays applied to carbon steel

  • Research Paper
  • Published:
Welding in the World Aims and scope Submit manuscript

Abstract

The embrittlement of the fusion boundary region of Ni–base Alloy 625 overlay welds on AISI 8630 steel was evaluated. Metallurgical characterization, thermodynamic and kinetic simulations, and hydrogen charging experiments were conducted in an effort to identify the embrittlement mechanism and simulate the type of failures that occur in service under cathodic protection. Optical microscopy, scanning electron microscopy, electron backscattered diffraction, electron probe microanalysis, X-ray diffraction, and hardness mapping were all used to characterize the microstructure and assist in identifying the microstructural features in the transition region of this dissimilar alloy combination that can promote susceptibility to hydrogen-assisted cracking (HAC). A special low-angle sectioning technique was developed that expanded the very narrow transition zone between the Alloy 625 overlay and the heat-affected zone of the 8630 steel. Using this technique, a “featureless zone” resulting from planar solidification was evaluated. This was the region in which HAC was observed during service under cathodic protection. Carbon migration studies conducted using Dictra™ showed that considerable carbon buildup (over 1 wt.%) occurs in the transition zone during postweld heat treatment. This level of carbon was confirmed using electron probe microanalysis. The high carbon content stabilizes the austenite phase in this region and results in local hardness levels exceeding 500 VHN. Metallographic sections of samples that failed under cathodic charging revealed that cracking occurs preferentially within this hardened region. The paper describes the metallurgical basis for the formation of this transition zone in weld overlays of Ni–base filler metals on carbon steels.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18

Similar content being viewed by others

References

  1. Olden V, Kvaale PE, Simense PA, Aaldstedt S, Sloberg JK (2003). The effect of PWHT on the materials properties and microstructure in Inconel 625 and Inconel 725 buttered joints. OMAE 2003. Paper No. 37196. OMAE, Cancun, Mexico, June 2003, p. 7

  2. Beaugrand VCM, Smith LS, GittosMF (2009). Subsea dissimilar joints: failure mechanisms and opportunities for Mittigation. CORROSION 2009. Paper No. 09305. NACE, Atlanta, GA, p. 14

  3. Beaugrand VCM, Smith LS, Gittos MF (2009). Hydrogen embrittlement of 8630M/625 subsea dissimilar joints: factors that influence the performance. OMAE. Paper No. 80030. OMAE, Honolulu, HI, June 2009, p. 10

  4. Fenske JA, Robertson IM, Ayer R, Hulke M, Lillig D, Newbury B (2010) Hydrogen effects on failure mechanisms in Fe–Ni weldments. Microsc Microanal 16(suppl 2):776–777

    Article  CAS  Google Scholar 

  5. Gittos MF, Gooch TG (1992) The interface below stainless steel and nickel-alloy claddings. Weld J 71(12):461s–472s

    Google Scholar 

  6. Kou S (2002) Welding metallurgy, 2nd edn. Wiley, New York. ISBN 978-0-471-43491-7

    Book  Google Scholar 

  7. Nelson TW, Lippold JC, Mills MJ (1999) Nature and evolution of the fusion boundary in ferritic–austenitic dissimilar metal welds—part 1: nucleation and growth. Weld J 78(10):329s–337s

    Google Scholar 

  8. Nelson TW, Lippold JC, Mills MJ (2000) Nature and evolution of the fusion boundary in ferritic–austenitic dissimilar metal welds—part 2: on-cooling transformations. Weld J 79(10):267-s–277-s

    Google Scholar 

  9. Nelson TW, Lippold JC, Mills MJ (1998) Investigation of boundaries and structures in dissimilar metal welds. Sci Tech Weld Join 3(5):249

    Article  CAS  Google Scholar 

  10. Rowe MD, Nelson TW, Lippold JC (1999) Hydrogen-induced cracking along the fusion boundary of dissimilar metal welds. Weld J 78(2):31s–37s

    Google Scholar 

  11. Alexandrov BT, Lippold JC (2010) In-situ determination of phase transformations and structural changes during non-equilibrium material processing. In: In-situ studies with photons, neutrons and electrons scattering. Springer, Berlin, pp. 113–131

  12. Alexandrov BT, Sowards JW, Lippold JC (2010). Low-angle sectioning technique for analysis of dissimilar weld interfaces. International Metallographic Contest 2010, poster No. 6-5-10. IMS, ASM, Portland, OR, July 2010

Download references

Author information

Author notes

  1. J. W. Sowards

    Present address: National Institute of Standards and Technology, Boulder, CO, USA

  2. D. R. Saltzmann

    Present address: Honda Research and Development, Marysville, OH, USA

Authors and Affiliations

  1. Welding Engineering Program, The Ohio State University, Columbus, OH, USA

    B. T. Alexandrov, J. C. Lippold, J. W. Sowards, A. T. Hope & D. R. Saltzmann

Authors
  1. B. T. Alexandrov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. J. C. Lippold
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. J. W. Sowards
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. A. T. Hope
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. D. R. Saltzmann
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to B. T. Alexandrov.

Additional information

Doc. IIW-2335 recommended for publication by Commission IX “Behaviour of Metals Subjected to Welding”.

In this paper, “HAC” has been used as an all-inclusive generic term of the specific hydrogen embrittlement mechanisms that are reported.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Alexandrov, B.T., Lippold, J.C., Sowards, J.W. et al. Fusion boundary microstructure evolution associated with embrittlement of Ni–base alloy overlays applied to carbon steel. Weld World 57, 39–53 (2013). https://doi.org/10.1007/s40194-012-0007-1

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40194-012-0007-1

Keywords (IIW Thesaurus)

Search

Navigation