Solid polymer electrolyte water electrolysis

doi:10.1016/0360-3199(82)90050-7

International Journal of Hydrogen Energy

Volume 7, Issue 5, 1982, Pages 397-403

https://doi.org/10.1016/0360-3199(82)90050-7 Get rights and content

Abstract

Studies have been made on electrocatalysts and their plating methods to solid polymer electrolyte (SPE). Perfluorosulfonic acid polymer membranes (Dupont manufactured Nafion) were used as SPE. Noble metals and their alloys were directly attached to both sides of the membrane without a binder by special metal plating methods developed by the present authors. The methods, utilizing reactions of a metal salt solution with a reducing agent on the membrane surface, made it possible to increase the adhesive strength of electrocatalysts to the membrane and also to eliminate, almost perfectly, the resistance of electrocatalyst/SPE interface. Pretreatments of the membrane were also investigated in order to improve the adhesive property. It was found that hydrothermal treatment and gas plasma treatment were more effective. The constituents of cell voltage, i.e. anodic and cathodic overvoltages and ohmic drop, were measured for five noble metals and their alloys. The anodic overvoltages were a major constituent of voltage losses and depended distinctly on the kinds of electrocatalysts used. The anodic overvoltage increased in the following order: Ir < Rh < Rh/Pt < Pt/Ru < Pt < Pd. Pure Ru had high initial activity. However, it was corroded during oxygen evolution. The electrodes based on Ir-Ir alloys were the best electrocatalysts for oxygen evolution and had a Tafel slope of 40–60 mV decade⁻¹. The effects of the operating temperature on the cell performance were also studied. The cathode and anode were a thin layer of Pt and similar layer of Ir alloy, respectively. The cell voltage decreased with an increase in temperature. At a current density of 500 mA cm⁻² and at 90°C, the cell voltage was 1.56–1.59 V corresponding to a thermal efficiency (based on ΔH) of 93–95%.

References (12)

L.J. Nuttall
Int. J. Hydrogen Energy
(1977)
L.J. Nuttall et al.
Int. J. Hydrogen Energy
(1980)
M.H. Miles et al.
Electrochimica Acta
(1978)
L.J. Nuttall et al.
P.W.T. Lu et al.
J. Appl. Electrochem.
(1979)
W.G.F. Grot et al.

There are more references available in the full text version of this article.

Cited by (240)

Parametric study on electrochemical reforming of glycerol for hydrogen production
2022, International Journal of Hydrogen Energy
Hydrogen production by electrochemical reforming of glycerol was investigated in this study. Within this scope, the performance of the system under different operating conditions was evaluated by parametric studies and optimum operating conditions were determined. The effects of membrane type, membrane pre-treatment procedure and temperature were investigated. System performance was examined also with long-term tests. The formation of hydrogen at the cathode was determined by analyzing the product gases by gas chromatography. Optimum condition for maximum hydrogen production was obtained with the Zn/Zn electrode pair in the presence of 0.4 M glycerol and 0.04 M H₂SO₄ at the anode side, 0.04 M H₂SO₄ at the cathode side and with pre-treated Nafion XL membrane. As the result of performance tests, room temperature and 2 V potential were found to be the most suitable operating conditions.
Operating an ozone-evolving PEM electrolyser in tap water: A case study of water and ion transport
2022, Separation and Purification Technology
While PEM water electrolysis could be a favourable technique for in situ sanitization with ozone, its application is mainly limited to the use of ultrapure water to achieve a sufficient long-time stability. As additional charge carriers influence the occurring transport phenomena, we investigated the impact of different feed water qualities on the performance of a PEM tap water electrolyser for ozone evolution. The permeation of water and the four most abundant cations (Na⁺, K⁺, Ca²⁺, Mg²⁺) is characterised during stand-by and powered operation at different charge densities to quantify underlying transport mechanisms. Water transport is shown to linearly increase with the applied current (95 ± 2 mmol A⁻¹ h⁻¹) and occurs decoupled from ion permeation. A limitation of ion permeation is given by the transfer of ions in water to the anode/PEM interface. The unstabilized operation of a PEM electrolyser in tap water leads to a pH gradient which promotes the formation of magnesium and calcium carbonates and hydroxides on the cathode surface. The introduction of a novel auxiliary cathode in the anolytic compartment has shown to suppress ion permeation by close to 20%.
Non-precious hydrogen evolution reaction catalysts: Stepping forward to practical polymer electrolyte membrane-based zero-gap water electrolyzers
2022, Chemical Engineering Journal
Water electrolysis (WE) technologies powered by renewable energy sources are promising methods for sustainable hydrogen production as they do not contribute toward resource depletion and pollutant emissions. However, to benefit from these technologies, their high capital costs must be addressed. The development of non-precious catalysts for hydrogen evolution reaction, which is a hydrogen-generating electrochemical reaction in WE, addresses this issue. However, most non-precious hydrogen evolution catalysts have only been evaluated at the half-cell level, and their practical applicability to WE has not been confirmed. Herein, we review non-precious hydrogen evolution reaction catalysts implemented in anion and proton exchange membrane WE, which are efficient WE methods owing to their low ohmic losses and ease of product gas separation. We also discuss the importance of implementing non-precious catalysts in water electrolyzers and standardizing an evaluation method.
Stable and high-performance Ir electrocatalyst with boosted utilization efficiency in acidic overall water splitting
2021, Chemical Engineering Journal
The industrialization of solid polymer electrolyte water electrolysis (SPEWE) dominantly relies on electrocatalyst with high stability and efficiency for oxygen evolution reaction (OER) catalysis. In this work, we report a facile method to construct α-Ni(OH)₂@Ir core–shell nanoparticles as bifunctional electrocatalyst for acidic overall water splitting application. α-Ni(OH)₂@Ir requires lower overpotentials (238 mV and 20 mV) to achieve 10 mA cm⁻² in acidic OER and HER catalysis compared to benchmarked IrO₂ (332 mV) and Pt/C (36 mV); meanwhile, the OER mass activity at 1.55 V vs. RHE was 92 fold higher than IrO₂; HER mass activity at overpotential of 80 mV was 5 fold better than Pt/C. The boosted catalytic activity is due to the enhanced utilization efficiency of Ir stemmed from the ultrathin Ir shell (~1 nm). Moreover, 1.49 V is demanded for α-Ni(OH)₂@Ir to attain 10 mA cm⁻² in acidic overall water splitting, 110 mV lower than benchmarked Pt/C-IrO₂ system. Meanwhile, stable catalytic performance is recorded for 20 h.
Recent progress in preparation process of ionic polymer-metal composites
2021, Results in Physics
Ionic polymer-metal composite (IPMC) is a typical electroactive polymers material, which has the advantages of light weight, fast response, good flexibility, large deformation range and good biocompatibility, it has a broad application prospect in the fields of soft robot, biomedicine, micro/nano object operation and so on. In this paper, the deformation mechanism of IPMC is briefly described, and then the fabrication technology of IPMC at present stage is mainly introduced, it includes electroless plating, electroplating, sputtering deposition, solution casting, hot pressing, direct assembly and other preparation processes. From the point of view of the most basic preparation process of IPMC, the various preparation methods and the problems faced in the preparation process of IPMC were discussed and analyzed. Finally, the preparation process of IPMC was summarized, and the challenges and future development of IPMC were prospected. Through the summary of this paper, it is helpful to consider all kinds of factors comprehensively, and then develop a new preparation technology, which can promote the rapid application and development of IPMC.
Recent advances in non-precious metal electrocatalysts for pH-universal hydrogen evolution reaction
2021, Green Energy and Environment
Citation Excerpt :
The technical characteristics and the equipment structures of chlor-alkali electrolyzers are similar to that of the alkaline water electrolyzer, but the cathode and anode chambers are fed with the aqueous solutions of NaOH and NaCl, respectively (Fig. 2b). To break through the obstacles in the alkaline water electrolysis, the acidic water electrolyzers based on solid polymer electrolyte membrane (PEM) have been developed since 1973 (Fig. 2c) [28]. The good proton conductivity (0.1 ± 0.02 S cm−1) and low thickness of PEM could efficiently reduce the ohmic resistance of the electrolyzers.
Hydrogen production by water electrolysis is a compelling technology to produce fuels and chemicals powered by renewable energy. It is highly desirable to develop cost-effective and durable electrocatalysts for hydrogen evolution reaction (HER). This review has summarized recent progress in mechanism understanding of non-precious metal electrocatalysts for pH-universal HER. The general approaches have been demonstrated to overcome the activity/stability limitations of the electrocatalysts for HER in a broad pH range. The perspectives and challenges for the development of pH-universal HER electrocatalysts have also been proposed. This review sheds light on the design and fabrication of high-performance electrocatalysts for versatile HER-related energy technologies.

View all citing articles on Scopus

View full text

Solid polymer electrolyte water electrolysis

Abstract

Int. J. Hydrogen Energy

Int. J. Hydrogen Energy

Electrochimica Acta

J. Appl. Electrochem.