X-ray photoelectron spectroscopy and Auger electron spectroscopy studies on the passivation behavior of plasma-nitrided low alloy steel in nitric acid

https://doi.org/10.1016/0921-5093(91)90826-9Get rights and content

Abstract

Nitrided SAE 4140 steel has been passivated by concentrated nitric acid. The resulting film was characterized using a combination of surface-analytical techniques, such as X-ray photoelectron spectroscopy (XPS) to evaluate the chemical composition of the passive film. Auger electron spectroscopy (AES) combined with ion etching was used to determine the composition depth profiles of nitrided surface. It was found that preferential dissolution of iron leads to enhanced nitrogen and chromium concentrations within the oxynitrided layer. A dense protective oxynitrided layer was found to be formed on the nitrided surface when the concentration of nitric acid was high as 8 M. The results of X-ray diffraction, XPS and AES analyses conclude that the protective nitride layer is composed of (Fe, Cr)4N, (Fe, Cr)2−3N and CrN in the inner layer, Fe2O3, Cr2O3 and remnant nitrides in the middle layer and nitrides accompanying Cr(OH)3·H2O and γ′-FeOOH in the outermost layer.

References (47)

  • S.D. Chyou et al.

    Mater. Sci. Eng.

    (1990)
  • L. Fedrizzi et al.

    Surf. Coat. Technol.

    (1988)
  • V. Naik et al.

    Thin Solid Films

    (1989)
  • R.C. Newman et al.

    Corros. Sci.

    (1987)
  • P.D. Hicks et al.

    Corros. Sci.

    (1984)
  • P.L. Bonora

    Mater. Sci. Eng.

    (1985)
  • M. Iwaki

    Mater. Sci. Eng.

    (1985)
  • F. Marchetti et al.

    Mater. Sci. Eng.

    (1985)
  • R. Beneke et al.

    Corros. Sci.

    (1989)
  • O.T. Inal et al.

    Thin Solid Films

    (1982)
  • G. Hultquist et al.

    Corros. Sci.

    (1982)
  • K. Terashima et al.

    Mater. Sci. Eng.

    (1987)
  • F. Bodart et al.

    Mater. Sci. Eng.

    (1987)
  • H. Matsuta et al.

    Appl. Surf. Sci.

    (1988–1989)
  • H.G. Feller et al.

    Mater. Sci. Eng.

    (1985)
  • K. Asami et al.

    Corros. Sci.

    (1977)
  • K. Asami et al.

    Corros. Sci.

    (1976)
  • M. Iwaki et al.

    Mater. Sci. Eng.

    (1987)
  • K. Asami et al.

    Corros. Sci.

    (1977)
  • S.D.Chyou, H.C.Shih, S.Han, The corrosion behavior of plasma-nitrided SAE 4140 in aqueous solution, Proc. 1988 Annu....
  • H.C. Shih et al.

    Experimental potential-pH diagrams for untreated and plasma-nitrided alloy steel in chloride solutions

  • S.D. Chyou et al.

    Corrosion

    (1991)
  • K. Ibendorf et al.

    Surf. Eng.

    (1988)
  • Cited by (22)

    • Cracking behavior of AISI 316L stainless steel powder by gas nitriding and its influence on spark plasma sintering

      2022, Journal of Materials Research and Technology
      Citation Excerpt :

      Cr2O3 is very difficult to densify by sintering [42] and prevents the formation of sintering neck and resulted the undensified morphology of S316L, SN450 and SN500. However, N450 and N500 have higher nitrogen content through gas nitriding, and the beneficial effects of nitrogen alloying on corrosion resistance are summarized as the following: (1) nitrogen dissolves to form ammonia, which increases pH values and depresses oxidation inside a pit [43,44]; (2) nitrogen addition stabilizes the austenitic phase [45,46]; (3) nitrogen is involved in the formation of a dense nitrogen oxide layer [5]. Therefore, the corrosion resistance of SN450 and SN500 is improved to some extent compared with S316L.

    • Pitting corrosion and crevice corrosion behaviors of high nitrogen austenitic stainless steels

      2009, International Journal of Minerals, Metallurgy and Materials
    View all citing articles on Scopus

    Present address: Power Research Institute, Taiwan Power Company, 84 Ta-An Road, Shu-Lin, Taipei 23802, Taiwan.

    View full text