The densification mechanism of polyacrylonitrile carbon fibers during carbonization

doi:10.1016/S1872-5805(16)60031-8

New Carbon Materials

Volume 31, Issue 5, October 2016, Pages 550-554

https://doi.org/10.1016/S1872-5805(16)60031-8 Get rights and content

Abstract

The densification mechanism of polyacrylonitrile carbon fibers during carbonization from 900 to 1 400 °C was investigated. The density, elemental composition, microstructure and weight loss of the fibers, as well as the gases released during the process were analyzed to reveal the mechanism. Results indicated that the density of the fibers was strongly dependent on the carbonization temperature and reactions involved indifferent temperature regimes. Condensation, pyrolysis and graphitization reactions were dominant at low (<1 050 °C), medium (1 050-1 250 °C) and high (>1 250 °C) temperatures, respectively. The amount of small molecule gas released and the fiber density both increased rapidly with temperature when condensation reactions dominated. The fiber density decreased as a result of nitrogen release when pyrolysis reactions dominated above 1050 °C while the fiber density increased due to the growth and increase in order of the graphene layers during graphitization. The two fiber density maxima found with increasing carbonization temperature were attributed to the different reactions.

References (17)

M Li et al.
Interfacial improvement of carbon fiber/epoxy composites using a simple process for depositing commercially functionalized carbon nanotuves on the fibers [J]
Carbon
(2013)
Y J Tong et al.
Oxidation kinetics of polyacrylonitrile-based carbon fibers in air and the effect on their tensile properties [J]
Corrosion Science
(2011)
Gang-ping WU et al.
Microvoid evolution in carbon fibers during graphitization for the preparation of carbon/carbon composites [J]
New Carbon Materials
(2014)
A J Gao et al.
Influence of processing temperature on interfacial behavior of HKT800 carbon fiber with BMI and epoxy matrices [J]
Chinese Journal of Aeronautics
(2015)
J Mittal et al.
Denitrogenation behavior and tensile strength increase during carbonization of stabilized PAN fibers [J]
Carbon
(1998)
A Gupta et al.
New aspects in the oxidative stabilization of PAN-base carbon fibers [J]
Carbon
(1996)
A J Gao et al.
Densification mechanism of polyacrylonitrile-based carbon fiber during heat treatment [J]
Journal of Physics and Chemistry of Solids
(2011)
F Shameel et al.
Effect of density and fibre orientation on the ablation behaviour of carbon-carbon composites [J]
New Carbon Materials
(2010)

There are more references available in the full text version of this article.

Cited by (24)

Enhancing thermoelectric performance in carbon fiber-reinforced cement composites through boron doping
2023, Construction and Building Materials
Although carbon fiber-reinforced cements (CFRCs) have the potential for ambient energy harvesting, their low thermoelectric performance restricts their practical application in construction. In this study, we investigate the possibility of using boron doped carbon fibers to improve the thermoelectric performance of cement composites. The electrical conductivity of a single carbon fiber was significantly enhanced, reaching a value of 272.1 × 10² S/cm despite the limited amount of boron doping. This was due to the formation of highly aligned, dense, thin, and long domains within the carbon fibers, which facilitated electron flow. The pristine carbon fiber's hydrophilic surface retarded the hydration reaction, while the boron-doped carbon fiber's hydrophobic surface had a diminished impact on the hydration products. The highest power factor of 0.02 μW/mK² in cement composites was attained by incorporating boron doped carbon fibers, which exhibit outstanding electrical conductivity, into the cement matrix.
Research on dynamic microwave low-temperature carbonization of high performance carbon fiber
2022, Diamond and Related Materials
Polyacrylonitrile precursor was obtained by one-step method of polymerization and spinning. After conventional pre-oxidation at 180–280 °C in air, the polyacrylonitrile pre-oxidized fiber was carbonized at 600–1000 °C by microwave heating and conventional heating in nitrogen. An infrared thermometer is used to detect the surface temperature of the fiber in real time. The dielectric loss tangent (tanδ) increases first and then decreases with increasing temperature. The intensity of the A line of the MCF-1000 sample increases, the G line gradually separates from the D line, and the I_D/I_G value decreases. Compared with CCF-700, the tensile strength of MCF-700 is increased by 10.06%. The microwave carbonization method creates excellent carbon fiber tensile strength at a temperature of 200 °C lower than the conventional carbonization temperature. The initial modulus of MCF-700 is 51.33% higher than that of CCF-700. Microwave carbonization can obtain carbon fiber with a higher initial modulus at a lower carbonization temperature.
Radial microstructure development of polyacrylonitrile (PAN)-based carbon fibers
2022, Carbon
Citation Excerpt :
DTG curves obtained by a TGA experiment also showed a significant weight loss at ∼1000 °C (Fig. S2a). However, after the maxima, the density steadily decreases (1.75 g/cm3 at 1400 °C) because further gas release resulted in various nano/micro-defects [11,25]. In contrast, the tensile strength and modulus were gradually enhanced.
The radial microstructure development of polyacrylonitrile-based carbon fibers is traced during continuous carbonization from 400 to 1400 °C. Based on the changes in the microstructure and mechanical properties of the fibers, it is confirmed that they undergo four distinctive stages depending on the temperature: (1) further cyclization in a remained unstabilized structure (400–600 °C), (2) crosslinking by dehydrogenation (600–800 °C), (3) crosslinking by denitrogenation (1000–1200 °C), and (4) development of turbostratic structure (1200–1400 °C). A structural analysis of the surface, skin, and core regions reveals that the innermost structure (core) originates from a high degree of structural relaxation. In contrast, densification is dominated in the outermost structure (surface). Such a radial heterogeneity is attributed to gas evolution along the radial direction of the fibers during the high-temperature carbonization and fiber shrinkage. The tensile strength exhibits a strong relationship with the crystal sizes as compared to the degree of disorder and amorphous structures, indicating that the crystal growth by densification has a greater influence on the tensile properties than the structure relaxation.
Design of a ductile carbon nanofiber/ZrB<inf>2</inf> nanohybrid film with entanglement structure fabricated by electrostatic spinning
2021, Ceramics International
Polyacrylonitrile (PAN), a kind of multi-purpose man-made polymer material, has been widely used in various products, including carbon fiber precursor fiber manufacturing. Organic/inorganic nanocomposites can provide precursor material with unique properties due to optimal structural design. Herein, PAN based carbon nanofiber (CNF) coated zirconium borate (ZrB₂) particles fiber film was prepared via electrostatic spinning strategy. Crosslinking network between carbon atoms formed at 280 °C due to long chain PAN molecules, which underwent pyrolysis at 800–1200 °C. Scanning electron microscope analysis showed that ductile CNF/ZrB₂ hybrid material with entanglement structure was successfully fabricated. Phase composition of the materials was analyzed by X-ray diffractometer, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and Raman spectroscopy, which confirmed the presence of carbon atoms in the materials. Entanglement structure between CNFs and ZrB₂ enhanced tensile performance of nanohybrid film, in which CNF film with 25% ZrB₂ content exhibited optimal mechanical properties. The design of nanohybrid structure provides facile and universal approach for exploration of organic/inorganic nanocomposites with controlled structures and excellent mechanical properties.
Tuning particle and phase formation of Sn/carbon nanofibers composite towards stable lithium-ion storage
2020, Journal of Power Sources
Sn is an attractive anodic material for lithium-ion batteries. High-temperature reduction is large-scale technique since most elemental Sn exists in the form of oxides. However, it is still a challenge to fabricate high performance Sn-based anodes with well-dispersed Sn nanoparticles in conductive matrix due to low melting point of Sn and tendency of particle agglomeration. Herein, we systematically investigate the influences of reduction conditions on particle and phase formation of Sn/carbon nanofibers (CNF) from electrospun SnO₂/polyacrylonitrile. It is shown that the SnO₂ can be reduced to Sn with slight aggregation at low temperature of 500 °C in a reducing atmosphere, but the composites possess poor electronic conductivity. As raising temperature, the grain size of Sn increases accordingly leading to sluggish Li⁺ internal diffusion dynamics. While in an inert atmosphere, the SnO₂ cannot be reduced completely at low temperature until 650 °C. By optimal control, the Sn/CNF–N₂-700 calcined at 700 °C in N₂ atmosphere presents the best electrochemical Li-ion storage performance among these samples, which delivers a reversible capacity of 932.2 mAh g⁻¹ at 100 mA g⁻¹ and stable cycling life with 760.3 mAh g⁻¹ retention after 200 cycles. This study may provide optimization guidance for industrial manufacture of Sn-based materials.
Firing mechanism of oxide-carbon refractories with phenolic resin binder
2018, Ceramics International
Citation Excerpt :
Concretely, the graphitic basal planes grow along the c-axis and a-axis, which shows that the random and disordered structure of the binder rearranges rapidly, increasing the extent of ordering of graphene layers [17,22,23]. During the above process, the small crystallites of the binder are transformed into large ones [27]. It is equivalent to reduce the distance among the original small crystallites, which is similar to the sintering of the powders that causes shrinkage.
Oxide-carbon refractories, usually using phenolic resin as a binder, have been widely applied in metallurgical industry. Their firing has important effect on the properties, such as strength, porosity and thermal stability of the binder. Main processes occurring during the firing have been investigated. Below 750 °C, the binder decomposition was the main process. Its critical range was 400–600 °C, lots of functional groups decomposed, which caused a large amount of volatiles generated and many pores formed, leading to a fast decreasing of the strength by 50.1%. Above 750 °C, the binder shrinkage was the main process. At 750–800 °C, the crystallite size of the binder increased greatly, causing a rapid shrinkage and a fast decreasing of the porosity, which resulted in a significant increasing of the strength by 11.0%. As the temperature increased up to 950 °C, the shrinkage became slow, which leaded to that the porosity decreased slowly and the strength kept almost constant, implying that the thermal stability was good. Therefore, a slow heating rate was needed at 400–600 °C and 750–800 °C, and the firing temperature should exceed 800 °C.

View all citing articles on Scopus

View full text

NOTEThe densification mechanism of polyacrylonitrile carbon fibers during carbonization

Abstract

Carbon

Corrosion Science

New Carbon Materials

Chinese Journal of Aeronautics

Carbon

Carbon

Journal of Physics and Chemistry of Solids

Effect of density and fibre orientation on the ablation behaviour of carbon-carbon composites [J]

New Carbon Materials

NOTE
The densification mechanism of polyacrylonitrile carbon fibers during carbonization