Fully Inkjet-Printed Flexible Temperature Sensors Based on Carbon and PEDOT:PSS1

https://doi.org/10.1016/j.matpr.2016.02.005Get rights and content

Abstract

Printed organic sensors on plastic substrates are of great interest due to their flexibility and low-cost fabrication. We here present a fully inkjet-printed flexible Wheatstone bridge used for temperature sensing. A carbon nanoparticle ink and a mixture of poly(3,4-ethylenedioxythophene):poly(4-styrene-sulfonate) (PEDOT:PSS) and dimethyl sulfoxide (DMSO) are used as positive (PTC) and negative (NTC) thermal coefficient materials, respectively. Different carbon inks and DMSO concentrations from 0.5 to 40 wt% are evaluated in order to optimize the temperature coefficient of resistance (TCR) and the reliability of the PTC and NTC materials. The single materials are printed on PEN substrates, and subsequently encapsulated. A climate chamber is used to evaluate their reliability. The Wheatstone bridge sensors show good linearity and little hysteresis within a temperature range of 20 °C to 70 °C and exhibit a sensitivity of ∼4 mV/°C at a bias current of 1 mA. We furthermore investigate the reproducibility of the temperature sensor fabrication in order to analyze the potential of industrial applicability of inkjet-printing.

References (19)

  • Y.-D. Lee et al.

    Sensors and Actuators B: Chemical

    (2009)
  • B. Meier et al.

    Thin Solid Films

    (2011)
  • A. Aliane et al.

    Microelectronics Journal

    (2014)
  • J.Y. Kim et al.

    Synthetic Metals

    (2002)
  • J. Ouyang et al.

    Polymer

    (2004)
  • A. Pantelopoulos et al.

    IEEE Transactions on Systems, Man, and Cybernetics

    Part C: Applications and Reviews

    (2010)
  • S. Patel et al.

    Journal of NeuroEngineering and Rehabilitation

    (2012)
  • C. Zhu et al.

    IEEE Transactions on Systems, Man and Cybernetics

    Part A: Systems and Humans

    (2011)
  • C. Zhu et al.

    IEEE International Conference on Robotics and Automation

    2009, ICRA’09

    (2009)
There are more references available in the full text version of this article.

Cited by (78)

  • Flexible and printable integrated biosensors for monitoring sweat and skin condition

    2023, Analytical Biochemistry
    Citation Excerpt :

    The calibration results further prove the feasibility of the skin impedance sensor. For the temperature sensor, as shown in Fig. 3C, because of the positive thermal coefficient feature of carbon for temperature [23], resistances of the temperature sensor would increase with a raised temperature with a R2 of 0.997 and a sensitivity of 2.1 Ω for skin temperature, demonstrating the perfect linearity and performance of the temperature sensor. Figs. S5 and S6 show the stability of the skin impedance and temperature sensors.

  • Inkjet-printed flexible sensors: From function materials, manufacture process, and applications perspective

    2022, Materials Today Communications
    Citation Excerpt :

    Flexible sensors based on inkjet printing technology have been noticed. Lots of researchers are dedicated to applying the inkjet printing technology for novel flexible sensors development, such as gas sensors [34–36], biomedical sensors [22,37,38], temperature and humidity sensors [24,39–41], and other sensors [11,42–44]. Challenges and critical technologies of flexible sensors fabrication by inkjet printing are also discussed, such as droplet dynamics, functional ink materials, and printing process, and so on.

View all citing articles on Scopus

Selection and peer-review under responsibility of the Conference Committee Members of NANOTEXNOLOGY2015 (12th International Conference on Nanosciences & Nanotechnologies & 8th International Symposium on Flexible Organic Electronics).

1

This is an open-access article distributed under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike License, which permits non-commercial use, distribution, and reproduction in any medium, provided the original author and source are credited.

View full text