Elsevier

Materials Science and Engineering: A

Volume 556, 30 October 2012, Pages 970-973
Materials Science and Engineering: A

Rapid communication
Influence of silicon on secondary hardening of 5 wt% Cr steels

https://doi.org/10.1016/j.msea.2012.06.060Get rights and content

Abstract

Silicon is long-known in the literature for its effect in the strength and tempering reactions of carbon steels, but only recently the effects of silicon in 5% Cr tool steels were deeply studied. The effects of Si on the toughness and fracture behavior in this class of steels were clearly elucidated, but the understanding on the tempering hardening was still open, due to the difficulties in splitting the two important contributions of silicon, i.e. solid solution strengthening and the implications in the precipitation of alloy carbides. In the present paper, these effects were separated, by excluding the solid solution contributions from Si, Mn and Cr, as well as, comparing the different steels to a typical tempering behavior of a reference carbon steel. This procedure leads to a clear observation, not yet shown in the literature, for the negative effect of silicon on the precipitation hardening during tempering. The correlation with secondary carbide distributions and other data from literature reinforces the mechanical behavior observed in the tempering curves.

References (20)

  • R.A. Mesquita et al.

    Mater. Sci. Eng. A

    (2011)
  • D. Delagnes et al.

    Mater. Sci. Eng. A

    (2005)
  • G. Roberts et al.

    Tool Steels

    (1998)
  • F.B. Pickering, Precipitation in Steels, Iron and Steel Institute, Special Report, vol. 64, 1959, p....
  • R. Banerjee

    J. Iron Steel Inst.

    (1965)
  • K. Miyata et al.

    Metall. Mater. Trans. A

    (2003)
  • H.M. Lee et al.

    Metall. Mater. Trans. A

    (1992)
  • J. Bourrat, US Patent 5622674,...
  • B. Klarenfjord, O. Sandberg, US Patent 6365096,...
  • R.A. Mesquita et al.

    Metall. Mater. Trans. A

    (2011)
There are more references available in the full text version of this article.

Cited by (14)

  • Microstructure and mechanical properties from an attractive combination of plasma nitriding and secondary hardening of M50 steel

    2018, Applied Surface Science
    Citation Excerpt :

    For the substrate hardness, a typical secondary hardening peak (i.e. a maximum tempering hardness of 691 HV) could be observed at about 520 °C, beyond this temperature, softening occurs. Variations of hardness are in good correspondence with the secondary hardening curve in tempering reported in [25,28], indicating a wonderful combination of mechanical properties between the nitrided surface layer and the substrate can be achieved in M50 steel. The surface hardness is significantly increased and the substrate is not softened or even higher.

  • Heat Treatment of Tool Steels

    2017, Comprehensive Materials Finishing
  • Microstructure, mechanical properties and strengthening mechanisms of 5Cr5MoV modified by aluminum

    2015, Materials and Design
    Citation Excerpt :

    The hardness–tempering temperature curves of 5Cr5MoV–xAl steels are shown in Fig. 8. It is generally known that the secondary hardening in Cr–Mo–V steel mainly caused by the dispersive precipitation of secondary carbides [25,26]. It can be found that the temperature at which the secondary hardening peak occurs is fairly constant with the aluminum concentration up to 1.63 wt.

  • Effect of double quenching and tempering heat treatment on the microstructure and mechanical properties of a novel 5Cr steel processed by electro-slag casting

    2014, Materials Science and Engineering: A
    Citation Excerpt :

    As reported in previous investigations [36,37], Si could suppress the formation of cementite, and thus would also affect the subsequent formation and distribution of alloy carbides which precipitated during the tempering process. Due to the suppression of cementite formation by Si, the anticipation of alloy carbides formation during tempering would occur, especially M7C3 [38]. As a result, M7C3 nucleated directly along the lath and prior austenite grain boundaries, on which alloy elements and carbon diffused faster.

  • Tempered Hardness Optimization of Martensitic Alloy Steels

    2023, Integrating Materials and Manufacturing Innovation
View all citing articles on Scopus
View full text