Abstract
The introduction sets the scene of the present paper, i.e. the extensive research works performed at the University of Liege in order to derive acceptable calculation methods for the fire design of concrete columns. It is explained that all previous works have been based on square or rectangular cross sections, for which corner spalling was observed very often, whereas circular section are nowadays becoming more and more popular.
In order to examine the influence of the circular shape on the behavior under fire conditions, an experimental research study has been performed recently at the University of Liege. This paper describes the test procedure, the observations made, and the values obtained for the fire resistance. Theoretical methods have been developed for a quick, safe, and efficient design of concrete columns under fire conditions. These methods have been applied successfully to the recently tested circular columns.
Similar content being viewed by others
References
CEB, “Fire Design of Concrete Structures in Accordance with CEB/FIP Model Code 90,” Bulletin d'Information du Comité Euro-International du Béton, no. 208, Lausanne, 1991.
EC2–1.2, “Eurocode 2: Design of Concrete Structures—Part 1.2: General Rules—Structural Fire Design,” European prestandard ENV 1992–1.2, CEN, Bruxelles, 1995.
J.-C. Dotreppe, J.-M. Franssen, A. Bruls, R. Baus, P. Vandevelde, R. Minne, D. Van Nieuwenburg, and H. Lambotte, “Experimental Research on the Determination of the Main Parameters Affecting the Behavior of Reinforced Concrete Columns Under Fire Conditions,” Magazine of Concrete Research, vol. 49,no. 179, Thomas Telford Ltd, London, 1997, pp. 117–127.
R. Hass, “Practical Rules for the Design of Reinforced Concrete and Composite Columns Submitted to Fire,” Technical Report 69, in german, T.U. Braunschweig, 1986.
T.T. Lie and J.L. Woollerton, “Fire Resistance of Reinforced Concrete Columns Test Results,” Technical Report 569, NRCC, Ottawa, 1988.
J.-C. Dotreppe and J.-M. Franssen, “Fire Attack on Concrete Columns and Design Rules Under Fire Conditions,” in Computational and Experimental Methods in Mechanical and Thermal Engineering, Proceedings of an International Symposium, Academia Press, Ghent, 1998, pp. 219–223.
J.-C. Dotreppe, J.-M. Franssen, and Y. Vanderzeypen, “Calculation Method for Design of Reinforced Concrete Columns Under Fire Conditions,” ACI Structural Journal, vol. 96,no. 1, 1999, pp. 9–18.
C.-M. Aldea, J.-M. Franssen, and J.-C. Dotreppe, “Fire Tests on Normal and High Strength Reinforced Concrete Columns,” in Fire Performance of High Strength Concrete, Proceedings of an International Workshop, NIST-National Institute of Standards and Technology, Gaithersburg, MD, 1997, pp. 109–124.
J.-C. Dotreppe, “Influence of Concrete Quality on Spalling of Short Columns Submitted to Fire Conditions,” in Challenges for Concrete in the Next Millenium, D. Stoelhorst and G.P.L. den Boer Ed., Proceedings of the XIIIth FIP Congress, Amsterdam, 1998, pp. 219–223.
K.D. Hertz, “A Survey of a System of Methods for Fire Safety Design of Traditional Concrete Constructions,” in Structures in Fire, J.-M. Franssen Ed., Proceedings of the First International Workshop, Copenhagen, University of Liege, 2000, pp. 283–292.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Franssen, JM., Dotreppe, JC. Fire Tests and Calculation Methods for Circular Concrete Columns. Fire Technology 39, 89–97 (2003). https://doi.org/10.1023/A:1021783311892
Issue Date:
DOI: https://doi.org/10.1023/A:1021783311892