nach oben

Physics of Metals and Metallography

Erschienen in:

01.11.2019 | STRUCTURE, PHASE TRANSFORMATIONS, AND DIFFUSION

Structure Formation and Properties of Eutectic Silumin Obtained Using Selective Laser Melting

verfasst von: I. G. Brodova, O. A. Chikova, A. N. Petrova, A. G. Merkushev

Erschienen in: Physics of Metals and Metallography | Ausgabe 11/2019

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

An Al–Si eutectic alloy was synthesized by the selective laser melting (SLM) method using a pilot wrought Al-Si powder (of Russian AKD-12 grade) as the starting material. On the basis of electron microscopy, the microstructure of the SLM alloy was certified with EDS mapping of elements (Al and Si). It has been established that the main structural component is an Al-based solid solution with a cellular-dendritic structure (with an average cell size of ~500 nm). The Si phase, which is a component of the eutectic, is located at the boundaries in the form of rounded crystals about ten nanometers in size. This paper presents the results of measuring the mechanical and nanomechanical properties, which show the competitiveness of the use of the pilot (experimental) powder.

Vorheriger Artikel Structural Changes during Thermal and Radiation Impacts in a Stainless Steel Alloyed with Titanium

Nächster Artikel Hot Deformation Behavior of 6063 Aluminum Alloy Studied Using Processing Maps and Microstructural Analysis

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Wirtschaft"

Online-Abonnement

Mit Springer Professional "Wirtschaft" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 340 Zeitschriften

aus folgenden Fachgebieten:

Bauwesen + Immobilien
Business IT + Informatik
Finance + Banking
Management + Führung
Marketing + Vertrieb
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

E. N. Kablov, “Additive technology is the dominant national technology initiative,” Intellekt i Tekhnologii, No. 2 (11), 52–55 (2015).

D. K. Ryabov, V. V. Antipov, V. A. Korolev, and P. N. Medvedev, “Influence of technological factors on the structure and properties of silumin obtained using selective laser synthesis technology,” Aviatsionnye Materialy i Tekhnologii, No. S1, 44–51 (2016).

N. V. Dynin, A. O. Ivanova, D. V. Khasikov, and M. S. Oglodkov, “Selective laser melting of aluminum alloys,” Electronic Scientific Journal. Trudy VIAM, No. 8 (56), (2017). https://doi.org/10.18577/2307-6046-2017-0-8-2-2

N. V. Kazantseva, I. V. Ezhov, N. I. Vinogradova, M. V. Il’inykh, A. S. Fefelov, D. I. Davydov, O. A. Oleneva, and M. S. Karabanalov, “Effect of Built geometry on the microstructure and strength characteristics of the Ti–6Al–4V alloy prepared by the selective laser melting,” Phys. Met. Metallogr. 119, No. 11, 1079–1086 (2018).CrossRef

X. P. Li, X. J. Wanga, M. Saunders, A. Suvorova, L. C. Zhang, Y. J. Liu, M. H. Fang, Z. H. Huang, T. B. Sercombe, “A selective laser melting and solution heat treatment refined Al–12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility,” Acta Mater. 95, 74–82 (2015).CrossRef

K. G. Prashanth, S. Scudino, H. J. Klauss, K. B. Surreddi, L. Löber, Z. Wang, A. K. Chaubey, U. Kühn, and J. Eckert, “Microstructure and mechanical properties of Al–12Si produced by selective laser melting: Effect of heat treatment,” Mater. Sci. Eng., A 590, 153–160 (2014).CrossRef

N. Kang, P. Coddet, L. Dembinski, H. Liao, and C. Coddet, “Microstructure and strength analysis of eutectic Al–Si alloy in-situ manufactured using selective laser melting from elemental powder mixture,” J. Alloys Compd. 691, 316–322 (2017).CrossRef

J. Suryawanshi, K. G. Prashanth, S. Scudino, J. Eckert, Om. Prakash, and U. Ramamurty, “Simultaneous enhancements of strength and toughness in an Al–12Si alloy synthesized using selective laser melting,” Acta Mater. 115, 285–294 (2015).CrossRef

I. Maskery, N. T. Aboulkhair, A. O. Aremu, C. J. Tuck, I. A. Ashcroft, R. D. Wildman, R. J. M. Hague, “A mechanical property evaluation of graded density Al–Si10–Mg lattice structures manufactured by selective laser melting,” Mater. Sci. Eng., A 670, 264–274 (2016).CrossRef

10.

A. M. Samuel, G. H. Garza-Elizondo, H. W. Doty, and F. H. Samuel, “Role of modification and melt thermal treatment processes on the microstructure and tensile properties of Al–Si alloys,” Mater. Des. 80, 99–108 (2015).CrossRef

11.

T. Kimura, “Effect of silicon content on densification, mechanical and thermal properties of Al–xSi binary alloys fabricated using selective laser melting,” Mater. Sci. Eng., A 682, 593–602 (2017).CrossRef

12.

J. Zhao, M. Easton, M. Qian, M. Leary, and M. Brandt “Effect of building direction on porosity and fatigue life of selective laser melted AlSi12Mg alloy, Mater. Sci. Eng., A 729, 76–85 (2018).CrossRef

13.

S. A. Khairallah, A. T. Anderson, A. Rubenchik, and W. E. King, “Laser powder-bed fusion additive manufacturing: Physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones,” Acta Mater. 108, 36–45 (2016).CrossRef

14.

C. Galy, E. Le Guen, E. Lacoste, and C. Arvieu, “Main defects observed in aluminum alloy parts produced by SLM: From causes to consequences,” Addit. Manuf. 22, 165–175 (2018).CrossRef

15.

R. Rashida, S. H. Masooda, D. Ruana, S. Palanisamya, R. A. Rahman Rashida, J. Elambasseril, and M. Brandt, “Effect of energy per layer on the anisotropy of selective laser melted AlSi₁₂ aluminium alloy,” Addit. Manuf. 22, 426–429 (2018).CrossRef

16.

M. Fousová, D. Dvorský, A. Michalcová, and D. Vojtěcha, “Changes in the microstructure and mechanical properties of additively manufactured AlSi10Mg alloy after exposure to elevated temperatures,” Mater. Charact. 137, 119–126 (2018).CrossRef

17.

B. Chen, S. K. Moon, X. Yao, G. Bi, J. Shen, J. Umeda, and K. Kondoh, “Strength and strain hardening of a selective laser melted AlSi10Mg alloy,” Scr. Mater. 141, 145–149 (2017).CrossRef

18.

N. Takata, H. Kodaira, K. Sekizawa, A. Suzuki, and M. Kobashi, “Change in microstructure of selectively laser melted AlSi10Mg alloy with heat treatments,” Mater. Sci. Eng., A 704, 218–228 (2017).CrossRef

19.

S. Marola, D. Manfredi, G. Fiore, M. G. Poletti, M. Lombardi, P. Fino, and L. Battezzati, “A comparison of Selective Laser Melting with bulk rapid solidification of AlSi10Mg alloy,” J. Alloys Compd. 742, 271–279 (2018).CrossRef

20.

N. T. Aboulkhai, I. Maskery, and C. Tuck, “The microstructure and mechanical properties of selectively laser melted AlSi10Mg: The effect of a conventional T6-like heat treatment,” Mater. Sci. Eng., A 667, 139–146 (2016).CrossRef

21.

E. O. Olakanmi, “Selective laser sintering/melting (SLS/SLM) of pure Al, Al-Mg, and Al–Si powders: Effect of processing conditions and powder properties,” J. Mater. Process. Technol. 213, No. 8, 1387–1405 (2013).CrossRef

22.

A. S. Fefelov, A. G. Merkushev, and O. A. Chikova, “Microstructure and mechanical properties of Al–12Si produced by selective laser melting,” IOP Conf. Ser.: Earth Environ. Sci. IPDME-2017, 87, 09201 (2017).CrossRef

23.

I. G. Brodova, P. S. Popel’, N. M. Barbin, and N. A. Vatolin, Melts as a Basis for Formation of Structure and Properties of Aluminum Alloys (UrO RAN, Yekaterinburg, 2005) [in Russian].

24.

M. H. Nasaba, D. Gastaldib, N. F. Lecisa, and M. Vedania, “On morphological surface features of the parts printed by selective laser melting (SLM),” Addit. Manuf. 24, 373–377 (2018).CrossRef

25.

A. Aversa, M. Lorusso, G. Cattano, D. Manfredi, F. Calignano, E. P. Ambrosio, S. Biamino, P. Fino, M. Lombardi, and M. Pavese, “A study of the microstructure and the mechanical properties of an Al–Si–Ni alloy produced via selective laser melting,” J. Alloys Compd. 695, 1470–1478 (2017).CrossRef

26.

D. K. Kim, W. Woo, and J. H. Hwang, K. An, and S. H. Choi, “Stress partitioning behavior of an AlSi10Mg alloy produced by selective laser melting during tensile deformation using in situ neutron diffraction,” J. Alloys Compd. 686, 281–286 (2016).CrossRef

Titel: Structure Formation and Properties of Eutectic Silumin Obtained Using Selective Laser Melting
verfasst von: I. G. Brodova
O. A. Chikova
A. N. Petrova
A. G. Merkushev
Publikationsdatum: 01.11.2019
Verlag: Pleiades Publishing
Erschienen in: Physics of Metals and Metallography / Ausgabe 11/2019
Print ISSN: 0031-918X
Elektronische ISSN: 1555-6190
DOI: https://doi.org/10.1134/S0031918X19110024

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Wirtschaft"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 11/2019

Effect of Anisotropy of Elastic Energy on the Electron–Phonon Drag and Temperature Dependences of Thermal EMF in Potassium Crystals at Low Temperatures

Spontaneous Spin Reorientation in Gd–Co Amorphous Films

Vacancy Migration Energy in Steels and Alloys

Effect of Multipass on Microstructure and Impact Toughness of As-Cast Al–20Si Alloy via Friction Stir Processing

Change in Thermophysical Properties and Melting Temperature of Niobium with Increasing Pressure

Coatings Based on Al2Au Intermetallic Compound: Structure and Optical Properties