Abstract

Zinc oxide was obtained by precipitation in an emulsion system with zinc acetate used as a precursor of ZnO and potassium hydroxide or sodium hydroxide as a precipitating agent. The cyclohexane, as an organic phase, and a nonionic surfactant mixture were also used for preparation of the emulsion. By applying modifications of the ZnO precipitation process, such as changing the precipitating agent, composition of substrates, and the rate of substrate dosing, some interesting structures of ZnO particles were obtained. The morphology of the modified samples was analysed based on SEM (scanning electron microscope) and TEM (transmission electron microscope) images. Moreover the samples were characterised by determination of their dispersive properties using the noninvasive back scattering method (NIBS), adsorption parameters (BET), and crystalline structure (XRD). Thermogravimetric analysis (TG) as well as infrared spectrophotometry (FT-IR) was also applied. For selected samples their electrical properties (dielectric permittivity and electric conductivity) were also measured. The zinc oxide obtained consisted of particles in the shapes of solids, ellipsoids, rods, and flakes, with size ranging from 164 to 2670 nm and showed well-developed surface area with values as high as 20 m2/g.

1. Introduction

Zinc oxide, with its unique physical and chemical properties such as high chemical stability, high electrochemical coupling coefficient, broad range of radiation absorption, and high photostability, is a multifunctional material [13]. In material science zinc oxide is classified as a semiconductor in groups II–VI, whose covalence is at the border between ionic and covalent semiconductors. A broad energy band (3.37 eV), high bond energy (60 meV), and high thermal and mechanical stability at room temperature make it attractive for potential use in electronics, optoelectronics, and laser technology [47]. The piezo- and pyroelectric properties of ZnO mean that it can be used as a sensor, converter, energy generator, and photocatalyst in hydrogen production. Compared with TiO2, ZnO as a potential photocatalyst has the advantage of lower cost, absorption of more light quanta, and higher photocatalytic efficiencies for the degradation of several organic pollutants in both acidic and basic media compared with TiO2 [8]. Many strategies have been developed to improve the photocatalytic activity of ZnO nanostructures, such as changing the structural and morphological characteristics (size, shape, and crystalline structure) [9]. Because of ZnO’s hardness, rigidity, and piezoelectric constant it is a material important in the ceramics industry, while its low toxicity, biocompatibility, and biodegradability make it a material of interest for biomedicine and in proecological systems [10]. Zinc oxide occurs in a very rich variety of structures and offers a wide range of properties [11, 12]. A variety of methods for ZnO production [13, 14], such as a vapour deposition process [15], precipitation in water solution [16], hydrothermal synthesis [17, 18], a sol-gel process [19], precipitation from microemulsions [20], and a mechanochemical process [21], make it possible to obtain products with particles differing in shape, size, and spatial structure.

Zinc oxide can occur in one-(1D), two-(2D), and three-dimensional (3D) structures. One-dimensional structures make up the largest group, including nanorods [22, 23], -needles [24], -helixes, -springs and -rings [25], -ribbons [26], -tubes [2729], -belts [30], -wires [31], -combs [32], and so forth; 1D structures were synthesised by Shouli et al. [33]. The same authors obtained three different morphological forms of zinc oxide, namely needles, pencils, and flowers, in the process of hydrothermal precipitation in the presence of CTAB and SDS. Their results pointed to the important role of surfactants in the morphology of the zinc oxide nanocrystals. When studying the relation between the gas properties and calcination conditions, the same authors established that the best crystallisation of zinc oxide and highest effectiveness of gas reactions were obtained for ZnO synthesis at 400°C for 1 hour.

Zinc oxide can be obtained in 2D structures, for example, nanoplate/nanosheet and nanopellets [34, 35]. Such particles have been obtained by Leung et al. [36], who precipitated ZnO with a structure of ribbons/combs by heating a mixture of ZnO : SWNT (single-walled carbon nanotubes) in a pipe furnace under atmospheric pressure. The morphology of the samples so obtained depends on the calcination temperature and substrates used. ZnO in the form of ribbons/combs shows strong UV absorption, which testifies to high purity of the crystalline samples obtained.

Examples of 3D structures of zinc oxide include flower, dandelion, snowflakes, coniferous urchin-like, and so forth [4, 3740]. ZnO with a 3D structure has been obtained by Haldar et al. [41], who applied the method of chemical condensation of vapours using zinc acetate as a precursor. They obtained zinc oxide in the form of nanorods joined in a kind of flower-like structure. The 3D structures are composed of ZnO nanorods of about 50 nm in diameter, hierarchically arranged about a common nucleus.

In this paper we report on the obtaining of ZnO in different morphological forms, by the method of emulsion precipitation (an alternative to the classical precipitation method and other frequently used complex procedures), with zinc acetate as a precursor of ZnO and potassium or sodium hydroxide as a precipitating agent.

2. Experimental Procedure

2.1. Materials

The precursors of zinc oxide were 0.9 M, 1.4 M, and 1.9 M solutions of dihydrate zinc acetate Zn(CH3COO)2·H2O (Chempur). The precipitating agent was a 1.8 M solution of potassium hydroxide KOH or sodium hydroxide NaOH, both from Chempur. Also used in emulsion formation were cyclohexane (Chempur) as an organic phase, and nonylphenylpolyoxyethylene glycol ethers NP3 and NP6 (Sigma-Aldrich) as a mixture of emulsifiers. All reagents were of analytical grade.

2.2. Emulsion Precipitation

Appropriate quantities of the emulsifiers (NP3 and NP6) were weighed and dissolved in the organic phase (cyclohexane), to which zinc acetate was added in a proper concentration. The mixture was homogenised for 30 minutes, after which the emulsion was ready for ZnO precipitation. Precipitation was carried out in a reactor of 500 cm3 capacity equipped with a homogenizer. The emulsion was placed in the reactor, to which a solution of KOH (or NaOH) was dosed using an Ismatec ISM833A type peristaltic pump. The system was intensely stirred (9000 rpm). The system obtained as a result of the reaction taking place in the reactor (QVF Mini-Plant Pilot Tec) was subjected to destabilisation at 80°C. Then the organic phase was separated by the vacuum evaporation technique and the mixture obtained was filtered off under reduced pressure. Next the sample was washed with hot water and methanol to remove residues of the emulsifiers. The filtrate cake was then dried in a stationary drier at 120°C to obtain the final product ZnO. Four samples were obtained, labelled as Z1, Z2, Z3, and Z4, composed of particles of different shapes. Table 1 presents the conditions of precipitation and main data for the samples, and Figure 1 shows the scheme for obtaining ZnO from the emulsion systems.

2.3. Physicochemical Characteristics of Precipitated ZnO
2.3.1. Dispersive Properties

Particle size distributions were determined using a Zetasizer Nano ZS (Malvern Instruments Ltd.), an analyser based on the noninvasive back scattering method (NIBS). Cumulant analysis gives a width parameter known as the polydispersity, or the polydispersity index (PdI). Cumulant analysis is actually the fit of a polynomial to the log of the G1 correlation function (1): The value of b is known as the second order cumulant, or the z-average diffusion coefficient. The coefficient of the squared term, c, when scaled as , is known as the polydispersity.

2.3.2. Scanning Electron Microscopy

At the next stage, morphology and microstructure were investigated to obtain data on dispersion, grain morphology, structure of individual particles, and agglomeration types in the obtained zinc oxide. The studies were performed using a Zeiss EVO40 scanning electron microscope and a Jeol 1200 EX II transmission electron microscope.

2.3.3. Adsorption Properties

In order to characterise the adsorption properties, nitrogen adsorption/desorption isotherms at 77 K and parameters such as surface area (), total volume (), and mean size (Sp) of pores were determined using an ASAP 2020 instrument (Micromeritics Instrument Co.). All samples were degassed at 120°C for 4 h prior to measurement. The surface area was determined by the multipoint BET (Brunauer-Emmett-Teller) method using the adsorption data as a function of relative pressure (). The BJH (Barrette-Joyner-Halenda) method was applied to determine the pore volume and the average pore size.

2.3.4. X-Ray Diffraction

The crystalline structure of individual samples was resolved using the X-ray diffraction method. The diffractograms were recorded using a TUR-M-62 horizontal diffractometer, equipped with HZG-3 type goniometer. To obtain the radiation intensity distribution curve , a counting rate gauge was used, interoperating with the counter and electronically coupled to a graphic recorder.

2.3.5. Thermal Stability

A thermogravimetric analyser (TG, model Jupiter STA 449F3, made by Netzsch) was used to investigate the thermal decomposition behaviour of the samples. Measurements were carried out under flowing nitrogen at a heating rate of 10°C/min and a temperature range of 25–1000°C with an initial sample weight of approximately 5 mg.

2.3.6. Fourier Transform Infrared Spectroscopy (FT-IR)

In order to identify the characteristic groups present on the surface of the precipitated ZnO, the samples were subjected to FT-IR analysis using an IFS 66 v/s spectrophotometer (Bruker). The samples were studied in the form of KBr tablets, as KBr crystals are inactive in the IR range. The analysis was performed over a range of 4000–400 cm−1.

2.3.7. Dielectric Properties and Conductivity

Dielectric properties of the samples were characterised by determination of the dielectric constant, conductivity, and refractive index. Dielectric and conductivity measurements were performed at room temperature in the range 10−2–107 Hz on an impedance analyser (Alpha-A High Performance Frequency Analyzer, Novocontrol GmbH). The refractive index was determined by approximation of the curves representing the frequency dependence of permittivity.

3. Results and Discussion

3.1. Dispersive and Morphological Characterisation of Zinc Oxide

SEM and TEM images of the ZnO samples precipitated from the emulsion system when different process parameters were applied (Table 1) revealed different and interesting structures of the products. Solid (sample Z1), ellipsoid (Z2), rod (Z3), and flake (Z4) morphologies were observed.

Figure 3 presents the particle size distributions recorded for the four samples. The low values of the polydispersity index (, Z3 PdI 0.127, and Z4 − PdI 0.055) imply that the particles have relatively high homogeneity and direct regular shapes (confirmed in the SEM and TEM images, see Figure 2). The particle size distributions display monomodal bands covering narrow ranges of particle diameters. The smallest size particles were obtained in sample Z1 (solids) and Z4 (flakes); their diameters varied in the range 164–955 nm (sample Z1) and 220–712 nm (sample Z4). The maximum volume contribution (close to 20%) came from particles of 396 nm diameter. The ellipsoid structures present in sample Z4 had diameters in the range 459–2670 nm; the maximum volume contribution of about 30% came from particles of 1110 nm diameter. The rod structures observed in sample Z3 had diameters in the range 396–825 nm, and the maximum volume contribution of about 20% came from particles of 815 nm diameter. By changing the precipitating agent (KOH or NaOH) we can vary the resulting ZnO particle structures. Using KOH results in two-dimensional shapes (solids, ellipsoids, rods). However when NaOH is used, we obtain particles in the form of flakes. The morphology is also affected by the concentration of zinc acetate and the quantity of the organic phase. It was observed in particular that as the quantity of the organic phase increases, there is an increase in the parameter reflecting the length of the resulting particles (a powder in the form of nanorods is obtained).

3.2. Adsorption Properties

Nitrogen adsorption/desorption isotherms and pore size distributions of the ZnO samples obtained are shown in Figure 4. The isotherms were classified as type IV and the hysteresis loops as type H3, which points to the mesoporous structure of the ZnO samples. A type IV isotherm is related to capillary condensation taking place in mesopores. As can be seen in Figure 4, the ZnO samples obtained in the manner described above have large specific surface areas, the largest (23 m2/g) being recorded for sample Z4 (flakes, Figure 4(d)). The pore volume and mean pore diameter in this sample were 0.015 cm3/g and 2.6 nm, respectively. The smallest specific surface area (8 m2/g) was determined for sample Z1 (solids, Figure 4(a)), and the pore volume and mean pore diameter in this sample were 0.006 cm3/g and 2.9 nm. The specific surface areas of sample Z2 (ellipsoids, Figure 4(b)) and sample Z3 (rods, Figure 4(c)) were 10.8 and 12.0 m2/g, while their pore volumes were 0.008 and 0.009 cm3/g and the mean pore diameters 2.7 and 2.9 nm, respectively. From analysis of the parameters of the ZnO precipitation process it can be concluded that with an increase in the concentration of zinc acetate and the quantity of the organic phase (cyclohexane) there is an increase in the specific surface area of the resulting samples. In addition the type of precipitating agent used significantly influences on the adsorption activity.

3.3. X-Ray Diffraction

The crystalline structure of the obtained zinc oxide samples was resolved by the X-ray diffraction method (XRD). WAXS diffraction patterns (Figure 5) confirmed the crystalline structure of the samples. All diffraction maxima observed correspond to the hexagonal structure of ZnO (JCPDS card number 36-1451 [4]). The diffraction maxima observed at the 2θ angles 31.8, 34.5, 36.3, 47.6, and 56.6 correspond to the characteristic ZnO planes of wurtzite structure: (100); (002); (101); (102); (110) [27, 28].

The average crystal size () of the ZnO samples was estimated from the width of lines in the XRD spectrum using the Sherrer equation: where K is a unitless constant taken as 0.9, λ is the X-ray wavelength (1.5418 Å), β is the width of the line at half-maximum intensity, and θ is half of the diffraction angle [42]. The values were calculated for the three highest intense peaks of the ZnO spectrum, which are (101), (002), and (100). The calculated average crystal sizes are detailed in Table 2.

3.4. Thermal Stability

The ZnO samples obtained were subjected to thermogravimetric (TG) analysis, which provides information on the chemical and physical transformations taking place upon heating. The TG curves recorded are presented in Figure 6. The greatest mass loss, of about 20% was observed for samples Z1 (solids) and Z3 (rods). For Z1 this decrease occurred in the temperatures range 20–500°C, while for Z3 it occurred in the two ranges 20–400°C and 400–800°C. A smaller mass loss of about 15% taking place in the range 20–500°C was noted for samples Z2 (ellipsoids) and Z4 (flakes). The mass loss in all samples is related to desorption of physically adsorbed water molecules on the ZnO surface. It follows that the degradation of samples Z1 and Z3 is faster than that of Z2 and Z4. The mass loss is caused mainly by thermal decomposition combined with water loss (water of crystallisation and constitutional water).

3.5. Spectroscopic Studies

In order to identify the characteristic groups present on the surface of the ZnO samples that could react with the functional groups of other compounds, the zinc oxides were subjected to spectroscopic analysis. The FT-IR spectra taken for samples Z2 (ellipsoids) and Z4 (flakes) are presented in Figure 7.

The spectroscopic analysis confirmed previously published results [4345]. The spectra reveal the presence of bands assigned to the oscillating vibrations νO–H (~3400 cm−1), symmetric and asymmetric valency bands νC–H (~3000; 1050 cm−1) and stretching vibrations νC=O (~1300; 1500 cm−1), νZn–OH (~900 cm−1), and νZn–O (~450 cm−1). The spectroscopic studies indirectly provide information about the surface character of the ZnO samples (intensity of hydroxyl group bands), which is of importance in applications of zinc oxide in nonpolar systems.

3.6. Electrical Properties

Figure 8 presents the relation of frequency versus permittivity measured for samples Z2 (ellipsoids) and Z4 (flakes). These two materials show high dispersion (strong dependence of permittivity versus frequency). The significant increase in permittivity in the low frequency range (below 100 Hz) is related to the large influence of conductivity. For frequencies above 10 kHz a tendency towards stabilisation of permittivity is observed, which is typical for dielectric materials at frequencies higher than the range corresponding to reorientational and ionic polarisation.

Figure 9 presents the conductivity of samples Z2 and Z4 as a function of frequency.

The values of conductivity measured for samples Z2 and Z4 are typical for insulators. In the frequency range 1–10000 kHz, the conductivity is described by relation (3): In the entire frequency (ω) range studied, the exponent P is 0.75 for Z4 (flakes) and 0.97 for Z2 (ellipsoids). For sample Z2 the character of the frequency dependence of conductivity is more gradual, while for Z4 it is more diffusional. The nature of the graph of conductivity versus frequency depends on the concentration of zinc acetate and the precipitating agent used. A smaller concentration of Zn(CH3COO)2 (0.9 M) and use of KOH make the curve more gradual, while increasing the concentration (1.4 M) and introducing NaOH produce a more diffusional curve. In the lowest frequency range the dependence shows a plateau characteristic of ohmic conductivity. The refractive index at the optical frequencies satisfies the following relation: For the samples studied this index was determined by approximation of the curves of frequency against permittivity. The values obtained are given in Table 3. The refractive index is influenced significantly by the reaction parameters—an increase in the concentration of zinc acetate and the use of NaOH instead of KOH as the precipitating agent cause a decrease in the value of this parameter.

4. Conclusions

Zinc oxide has been obtained in a number of different structures using a large number of methods which has so far been proposed. The relatively simple method for ZnO synthesis proposed in this paper makes it possible to obtain ZnO with particles in the shape of solids, ellipsoids, rods and flakes, and with very well-developed surface area. The structures of the product particles were found to depend on certain types of modification to the precipitation process. The analysis shows that the results obtained are clearly influenced by the parameters of the precipitation process. The shape of the ZnO particles depends on the concentration of zinc acetate, the type of precipitating agent, and the quantity of the organic phase. The diameters of the ZnO particles obtained varied in the range 164–2670 nm, while the specific surface areas ranged from 8 to 24 m2/g. The samples were found to display the crystalline structure of hexagonal wurtzite. The high value of the refractive index (close to 2.2), and high chemical resistance are very important and attractive features for potential applications. In summary, the proposed method of precipitation makes it possible to obtain ZnO powders with various interesting structures and properties, desirable for many applications. The same method can be used for obtaining oxides of other metals characterised by different nano- and microstructures. In the next stage of this research the zinc oxide obtained will be used as a photocatalyst.

Conflict of Interests

The authors informed equal contribution of each author in this paper and declared any conflict of interests in respect of our submitted paper.

Acknowledgments

This work was supported by Poznan University of Technology Research Grant no. 32-329/2012 DS-MK. The authors would like to thank Dominik Paukszta for his assistance with the XRD analysis.