ESTIMATION OF THE CHARACTERISTIC VALUE OF WOOD STRENGTH

Christoforo, André L.; Almeida, Andrea de S.; Lanini, Tamiris L. S.; Nogueira, Rodrigo de S.; Lahr, Francisco A. R.

doi:10.1590/1809-4430-Eng.Agric.v39n1p127-132/2019

ABSTRACT

For safety reasons, wood strength values, essential for structural dimensioning, are calculated based on the characteristic value, which corresponds to the 5% percentile of a given probability distribution model. For small samples, the Brazilian normative document ABNT NBR 7190 establishes an estimator of the characteristic wood strength, which can provide a significantly different result from the characteristic value coming from a suitable model of probability distribution. The main objective of this study was to evaluate the best probability distribution model (normal, lognormal, Weibull, and exponential) and the subsequent calculation of the characteristic value indicated by ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p., allowing to evaluate its accuracy, being also investigated two relationships between characteristic values of the simplified characterization condition for woods of species already known. The best adhesion model was the normal model, which resulted in values statistically equivalent to the characteristic values according to ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p.. Among the evaluated relationships, the obtained results were significantly higher (up to 92%) when compared to those estimated by ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p..

KEYWORDS
wood; compression; traction; shear; probability distribution; characteristic value

INTRODUCTION

Wood, a natural and renewable source material, has a good relationship between mechanical strength and density (Arruda et al., 2015Arruda LM, Del Menezzi CHS, Andrade A (2015) Utilization of a thermomechanical process to enhance properties of a hardwood used for flooring. Ciência da Madeira 6(3):223-231.; Baar et al., 2015Baar J, Tippner J, Rademacher P (2015) Prediction of mechanical properties - modulus of rupture and modulus of elasticity of five tropical species by nondestructive methods. Maderas: Ciencia y Tecnologia 17(2):239-252.; Cavalheiro et al., 2016Cavalheiro RS, Almeida DH, Almeida TH, Christoforo AL, Lahr FAR (2016) Density as estimator of shrinkage for some Brazilian Wood species. International Journal of Materials Engineering 6(3):107-112.), which makes it suitable for use in rural and civil constructions (Andrade Jr et al, 2014Andrade Jr JR, Almeida DH, Almeida TH, Christoforo AL, Stamato GC, Lahr FAR (2014) Avaliação das estruturas de cobertura em madeira de um galpão de estoques de produtos químicos. Ambiente Construído 14(3):75-85.; Chen & Guo, 2017Chen Y, Guo W (2017) Nondestructive evaluation and reliability analysis for determining the mechanical properties of old wood of ancient timber structure. BioResources 12(2):2310-2325., Lahr et al., 2017Lahr FAL, Christoforo AL, Varanda LD, Araujo VA, Chahud E, Branco LAMN (2017) Shear and longitudinal modulus of elasticity in wood: relations based on static bending tests. Acta Scientiarum-Technology 39:433-437.).

Brazil presents an enormous potential for wood applications since the availability of species from the Amazon Forest is of the order of 11194, cataloged between 1707 and 2015 (Steege et al., 2016Steege H, Vaessen RW, López DC, Sabatier D, Antonelli A, Oliveira SM, Pitman NCA, Jorgensen PM, Salomão RP (2016) The discovery of the Amazonian tree flora with an update checklist of all known tree taxa. Scientific Reports 6(29549):1-15.), which has motivated the development of new researches with the purpose of characterizing new species to substitute those commonly used in construction (Christoforo et al., 2017Christoforo AL, Aftimus BHC, Panzera TH, Machado GO, Lahr FAR (2017) Physico-mechanical characterization of the Anadenanthera colubrina Wood specie. Engenharia Agrícola 37(2):376-384.; Ferro et al., 2015Ferro FS, Icimoto FH, Almeida DH, Christoforo AL, Lahr FAR (2015) Influência da posição dos instrumentos de medida na determinação do módulo de elasticidade da madeira na compressão paralela às fibras (Ec0). Revista Árvore 39(4):743-749., Freitas et al., 2016Freitas AS, Gonçalez JC, Del Menezzi CH (2016) Tratamento termomecânico e seus efeitos nas propriedades da Simarouba amara (Aubl.). Floresta e Ambiente 23(4): 565-572.).

In Brazil, wooden structure projects are regulated by the Brazilian normative document ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p. named Wooden Structure Project, and the structures must be dimensioned to move very little (geometrical linearity) and also to withstand satisfactorily and safely to the action of acting forces.

Due to the safety of the structure project, the strength values to the mechanical stresses of wood are obtained based on the characteristic value, which corresponds to the 5% percentile of the respective probability distribution.

According to the probabilistic method of ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p., it is assumed normality in the distributions of strength values, and this hypothesis is based on the consideration of large samples (30 or more test specimens) together with a limit value of 18% of the coefficient of variation. Given the average strength value ( $\bar{f}$ ) and its standard deviation (sd), the characteristic value (f_wk) of the property is determined using [eq. (1)].

(1)

f_{w k} = \bar{f} - 1.645 \cdot s d

For a small number (n) of samples (n < 30), this normative document establishes the use of [eq. (2)] for estimating the characteristic strength value.

(2)

f_{w k} = (2 \cdot \frac{f_{1} + f_{2} + f_{3} + \dots + f_{(n / 2) - 1}}{(n / 2) - 1} - f_{n / 2}) \cdot 1.10

From [eq. (2)], n is the number of samples used in the mechanical tests and f_i consists of the strength values of the sample, and the results must be arranged in ascending order (f₁≤f₂≤f₃…≤f_n), disregarding the highest strength value if the number of test specimens is odd and not assuming for f_wk a value lower than f₁ nor lower than 70% of the average strength value.

The adoption of [eq. (2)] to estimate the characteristic value can result in significantly different values (or not) from the characteristic value associated to a given probability density function, considering the diversity of probability density functions (Pinto et al., 2004Pinto EM, Espinosa MM, Calil Jr C (2004) Métodos para Determinação do Valor Característico da Resistência à Compressão Paralela às Fibras da Madeira. Madeira: Arquitetura e Engenharia 5(14): 1-6.), and once that of better adherence to the set of strength values is found, the characteristic value can be obtained with a greater reliability. If the characteristic value estimated by this equation is higher than that obtained by a given probability distribution model, this implies overestimating wood strength and underestimating it otherwise (unfavorable conditions to the project), which motivates the development of researches in this area.

It is not always possible to obtain all the physical and mechanical properties of wood to be used in a structure project because such variables are determined by means of tests involving equipment usually found in large technological and research centers (Icimoto et al., 2015Icimoto FH, Ferro FS, Almeida DH, Christoforo AL, Lahr FAR (2015) Influence of specimen orientation on determination of elasticity in static bending. Maderas: Ciencia y Tecnologia 17(2): 229-238.).

In this sense, the Brazilian normative document ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p. proposes a simplified wood characterization, in which characteristic strength values are estimated through relationships, as in eqs (3) and (4), which are based on results obtained from the compression test in the direction parallel to the fibers.

(3)

f_{c 0, k} = 0.77 \cdot f_{t 0, k}

(4)

f_{v 0, k} = 0.12 \cdot f_{c 0, k}

In addition, as considered in this normative document, researches have been developed with the purpose of proposing relationships among wood properties, such as the studies developed by Dias & Lahr (2004)Dias FM, Lahr FAR (2004) Estimativa de propriedades de resistência e rigidez da madeira através da densidade aparente. Scientia Forestalis 65:102-113. and Almeida et al. (2016)Almeida TH, Almeida DH, Christoforo AL, Chahud E, Branco LAMN, Lahr FAR (2016) Density as estimator of strength in compression parallel to the grain in wood. International Journal of Materials Engineering 6(3):67-71., in which the density was used as an estimator (via regression models) of physical and mechanical properties.

Considering the use of four probability distribution models (normal, lognormal, Weibull, and exponential) and five wood species, this study aimed to evaluate the best distribution models in obtaining the characteristic values of tensile (f_t0,k), compressive (f_c0,k), and shear (f_v0,k) strengths in the direction parallel to wood fibers, allowing verifying possible differences in characteristic values derived from the use of the expression adopted by the Brazilian normative document NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p. (Equation 2). Besides the analysis of the characteristic value, the accuracy of eqs (3) and (4) proposed by this normative document was also evaluated.

MATERIAL AND METHODS

Strength properties (f_t0, f_c0, and f_v0) were obtained following the assumptions and the test and calculation methods of the normative document ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p..

In order to obtain a greater comprehension of results, wood species were used (Table 1), being divided into strength classes of the hardwood group (ABNT NBR 7190, 1997ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p.) with a moisture content close to 12%, which consists of the equilibrium moisture content indicated by this normative document.

Thumbnail

TABLE 1
Species of hardwood used.

The probability distributions considered in this research to determine the characteristic strength values consisted of normal, lognormal, Weibull, and exponential, whose probability density functions (f) on the random variable X are expressed in eqs (5), (6), (7), and (8), respectively.

(5)

f (x) = \frac{1}{\sqrt{2 \cdot π \cdot σ^{2}}} \cdot e^{\frac{1}{2} \cdot {(\frac{x - μ}{σ})}^{2}}, x \in (- \infty, \infty)

(6)

f (x) = {\begin{matrix} \frac{1}{x \cdot σ \cdot \sqrt{2 \cdot π}} \cdot e^{- \frac{1}{2} \cdot \frac{{(\log (x) - μ)}^{2}}{σ^{2}}}, if x > 0 \\ 0, o t h e r w i s e \end{matrix}

(7)

f (x) = {\begin{matrix} \frac{δ}{α^{δ}} \cdot x^{δ - 1} \cdot e^{- {(\frac{x}{α})}^{δ}}, x \geq 0 \\ 0, if x < 0 \end{matrix}

(8)

f (x) = {\begin{matrix} λ \cdot e^{- λ \cdot x}, if x \geq 0 \\ 0, if x < 0 \end{matrix}

In [eq. (5)], σ and μ consist of the standard deviation and the population mean, respectively. In [eq. (6)], σ is the standard deviation and μ is the population mean of the logarithm. In the Weibull probability density function (Equation 7), δ and α are the shape and scale parameters, respectively, and λ is the distribution rate parameter of the Exponential function (Equation 8).

The adhesion tests (at 95% confidence level) used to verify the best distribution model by property (f_t0, f_c0, and f_v0) were obtained by the least squares method using the software Minitab^® version 16.

The characteristic strength values were obtained using the probability distribution models and the equation from ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p. and the analysis of variance (ANOVA) was used to verify the influence of methodologies used to determine the characteristic values. ANOVA was considered at a 5% significance level. Considering the formulated hypotheses, a probability P (P-value) higher than or equal to the significance level implies in accepting that the means of the characteristic values (considering the five wood species together) by both methods are equivalent, and not equivalent otherwise (P-value < 0.05).

Estimates of the relationships between the characteristic strengths (Equations 3 and 4) were evaluated by the least squares method. The minimization of eqs (9) and (10) allows determining the coefficients α_i of the relationships f_c0,k = α₁·f_t0,k and f_v_0,k = α₂·f_c0_,k, respectively.

(9)

f (α_{1}) = \frac{1}{2} \sum_{i = 1}^{n} {(f_{c 0, k_{i}} - α_{1} \cdot f_{t 0, k_{i}})}^{2}

(10)

f (α_{2}) = \frac{1}{2} \sum_{i = 1}^{n} {(f_{v 0, k_{i}} - α_{2} \cdot f_{c 0, k_{i}})}^{2}

From each of the five wood species, 12 samples were manufactured for each of the three studied requests, totaling 180 experimental determinations.

RESULTS AND DISCUSSION

Figure 1 shows the average values, confidence intervals (95% confidence), and the ranges of variance of the coefficient of variation (CV) of the strength properties investigated for the woods of Cambará Rosa (CR), Cedro Amazonense (CA), Cupiúba (Cup), Guarucaia (Ga), and Roxinho (Ro).

FIGURE 1
Results of strength properties: f_C0 (a), f_t0 (b), and f_v0 (c)

Except for the parallel tensile strength of the Roxinho wood, the values of the coefficients of variation are in accordance with those refereed (18% for normal stresses and 28% for tangential stresses) by the Brazilian document ABNT NBR 7910 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p..

The average values of compressive (54.4 MPa) and tensile (62.1 MPa) strengths in the direction parallel to the Cupiúba wood fibers cited in Annex E of ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p. are close to the values obtained and shown in Figures 1a and 1b, respectively. Likewise, the values of f_C0 and f_t0 of the Guarucaia wood contained in this document are equal to 62.4 and 70.9 MPa, respectively, which are in accordance with those obtained in the present study.

Table 2 shows the values of characteristic strengths obtained by wood species and with the use of [eq. (2)].

Thumbnail

TABLE 2
Results of the characteristic strength values obtained by [] proposed by ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p. for the five wood species.

According to Table 2, Cambará Rosa, Cedro Amazonense, Guarucaia, Cupiúba, and Roxinho woods are, according to ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p., categorized in the strength classes D20, D40, D50, D60, and D60, respectively.

Table 3 shows the characteristic values associated with the best distribution models by property and wood species and Figure 2 shows the results of adhesion tests for the compressive strength parallel to the wood fibers of Cambará Rosa as an example of the choice of model.

Thumbnail

TABLE 3
Results of characteristic values associated with the best distribution models by property and wood species.

FIGURE 2
Normal (a), lognormal (b), Weibull (C), and exponential (d) distribution models to estimate the characteristic value of compressive strength in the direction parallel to the wood fibers Cambará Rosa.

Table 2 shows that the normal distribution model had the best adherence to the results of the investigated strength properties, followed by the lognormal model (results very close to the normal distribution), and the Weibull model. The exponential distribution model had no representativeness in all cases.

Figure 3 shows the results (P-values) of ANOVA regarding the possible differences between the average values of the characteristic strengths obtained using the equation proposed by ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p. and the normal distribution model (DProbN).

FIGURE 3
Results of ANOVA regarding the characteristic values obtained by the Brazilian standard and the normal distribution model: f_c0,k (a), f_t0,k (b), and f_v0,k (c).

Figure 3 shows that because the P-values were all higher than 0.05, the characteristic values of the three strength properties determined according to ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p. or by the normal probability distribution model were statistically equivalent, evidencing the accuracy of the model proposed by this normative document for small samples, suggesting the possibility of using [eq. (1)] also for small samples.

From the use of eqs (9) and (10), the values of the coefficients α₁ (f_c0,k=α₁·f_t0,k) and α₂ (f_v0,k=α₂·f_c0,k) of the investigated relationships resulted in 0.96 and 0.23, respectively, being 25 and 92% higher than the coefficients of eqs (3) and (4) indicated by ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p., showing they are adequate and favorable to the safety of structures. However, because the differences with the coefficients obtained in this study are significant, these values may overestimate the dimensions of the structure elements, directly affecting the final value of the work to be projected.

CONCLUSIONS

The results obtained in this research allow concluding that:

–
Among the tested probability distribution models, the normal model presented the highest adherence to the evaluated characteristic strength values, not being significant the exponential model.
–
The equivalence between the characteristic values obtained by the expression of the Brazilian standard and the characteristic values coming from the normal probability distribution models was observed from the statistical analysis, evidencing the accuracy in the estimation of the characteristic value for small samples.
–
As observed from the relationships between the characteristic values of the evaluated strength properties, the coefficients obtained in this study were significantly higher when compared to those of the relationships proposed by ABNT NBR 7190 (1997)ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p., which implies in more conservative estimates by this document for the evaluated species.

REFERENCES

ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p.
Almeida TH, Almeida DH, Christoforo AL, Chahud E, Branco LAMN, Lahr FAR (2016) Density as estimator of strength in compression parallel to the grain in wood. International Journal of Materials Engineering 6(3):67-71.
Andrade Jr JR, Almeida DH, Almeida TH, Christoforo AL, Stamato GC, Lahr FAR (2014) Avaliação das estruturas de cobertura em madeira de um galpão de estoques de produtos químicos. Ambiente Construído 14(3):75-85.
Arruda LM, Del Menezzi CHS, Andrade A (2015) Utilization of a thermomechanical process to enhance properties of a hardwood used for flooring. Ciência da Madeira 6(3):223-231.
Baar J, Tippner J, Rademacher P (2015) Prediction of mechanical properties - modulus of rupture and modulus of elasticity of five tropical species by nondestructive methods. Maderas: Ciencia y Tecnologia 17(2):239-252.
Cavalheiro RS, Almeida DH, Almeida TH, Christoforo AL, Lahr FAR (2016) Density as estimator of shrinkage for some Brazilian Wood species. International Journal of Materials Engineering 6(3):107-112.
Chen Y, Guo W (2017) Nondestructive evaluation and reliability analysis for determining the mechanical properties of old wood of ancient timber structure. BioResources 12(2):2310-2325.
Christoforo AL, Aftimus BHC, Panzera TH, Machado GO, Lahr FAR (2017) Physico-mechanical characterization of the Anadenanthera colubrina Wood specie. Engenharia Agrícola 37(2):376-384.
Dias FM, Lahr FAR (2004) Estimativa de propriedades de resistência e rigidez da madeira através da densidade aparente. Scientia Forestalis 65:102-113.
Ferro FS, Icimoto FH, Almeida DH, Christoforo AL, Lahr FAR (2015) Influência da posição dos instrumentos de medida na determinação do módulo de elasticidade da madeira na compressão paralela às fibras (E_c0). Revista Árvore 39(4):743-749.
Freitas AS, Gonçalez JC, Del Menezzi CH (2016) Tratamento termomecânico e seus efeitos nas propriedades da Simarouba amara (Aubl.). Floresta e Ambiente 23(4): 565-572.
Icimoto FH, Ferro FS, Almeida DH, Christoforo AL, Lahr FAR (2015) Influence of specimen orientation on determination of elasticity in static bending. Maderas: Ciencia y Tecnologia 17(2): 229-238.
Lahr FAL, Christoforo AL, Varanda LD, Araujo VA, Chahud E, Branco LAMN (2017) Shear and longitudinal modulus of elasticity in wood: relations based on static bending tests. Acta Scientiarum-Technology 39:433-437.
Pinto EM, Espinosa MM, Calil Jr C (2004) Métodos para Determinação do Valor Característico da Resistência à Compressão Paralela às Fibras da Madeira. Madeira: Arquitetura e Engenharia 5(14): 1-6.
Steege H, Vaessen RW, López DC, Sabatier D, Antonelli A, Oliveira SM, Pitman NCA, Jorgensen PM, Salomão RP (2016) The discovery of the Amazonian tree flora with an update checklist of all known tree taxa. Scientific Reports 6(29549):1-15.

Publication Dates

Publication in this collection
Jan-Feb 2019

History

Received
29 Nov 2017
Accepted
19 Dec 2018

This is an Open Access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

[1] ABNT - Associação Brasileira De Normas Técnicas (1997). NBR 7190: Projeto de estruturas de madeira. ABNT, 107 p.

[2] Almeida TH, Almeida DH, Christoforo AL, Chahud E, Branco LAMN, Lahr FAR (2016) Density as estimator of strength in compression parallel to the grain in wood. International Journal of Materials Engineering 6(3):67-71.

[3] Andrade Jr JR, Almeida DH, Almeida TH, Christoforo AL, Stamato GC, Lahr FAR (2014) Avaliação das estruturas de cobertura em madeira de um galpão de estoques de produtos químicos. Ambiente Construído 14(3):75-85.

[4] Arruda LM, Del Menezzi CHS, Andrade A (2015) Utilization of a thermomechanical process to enhance properties of a hardwood used for flooring. Ciência da Madeira 6(3):223-231.

[5] Baar J, Tippner J, Rademacher P (2015) Prediction of mechanical properties - modulus of rupture and modulus of elasticity of five tropical species by nondestructive methods. Maderas: Ciencia y Tecnologia 17(2):239-252.

[6] Cavalheiro RS, Almeida DH, Almeida TH, Christoforo AL, Lahr FAR (2016) Density as estimator of shrinkage for some Brazilian Wood species. International Journal of Materials Engineering 6(3):107-112.

[7] Chen Y, Guo W (2017) Nondestructive evaluation and reliability analysis for determining the mechanical properties of old wood of ancient timber structure. BioResources 12(2):2310-2325.

[8] Christoforo AL, Aftimus BHC, Panzera TH, Machado GO, Lahr FAR (2017) Physico-mechanical characterization of the Anadenanthera colubrina Wood specie. Engenharia Agrícola 37(2):376-384.

[9] Dias FM, Lahr FAR (2004) Estimativa de propriedades de resistência e rigidez da madeira através da densidade aparente. Scientia Forestalis 65:102-113.

[10] Ferro FS, Icimoto FH, Almeida DH, Christoforo AL, Lahr FAR (2015) Influência da posição dos instrumentos de medida na determinação do módulo de elasticidade da madeira na compressão paralela às fibras (E_c0). Revista Árvore 39(4):743-749.

[11] Freitas AS, Gonçalez JC, Del Menezzi CH (2016) Tratamento termomecânico e seus efeitos nas propriedades da Simarouba amara (Aubl.). Floresta e Ambiente 23(4): 565-572.

[12] Icimoto FH, Ferro FS, Almeida DH, Christoforo AL, Lahr FAR (2015) Influence of specimen orientation on determination of elasticity in static bending. Maderas: Ciencia y Tecnologia 17(2): 229-238.

[13] Lahr FAL, Christoforo AL, Varanda LD, Araujo VA, Chahud E, Branco LAMN (2017) Shear and longitudinal modulus of elasticity in wood: relations based on static bending tests. Acta Scientiarum-Technology 39:433-437.

[14] Pinto EM, Espinosa MM, Calil Jr C (2004) Métodos para Determinação do Valor Característico da Resistência à Compressão Paralela às Fibras da Madeira. Madeira: Arquitetura e Engenharia 5(14): 1-6.

[15] Steege H, Vaessen RW, López DC, Sabatier D, Antonelli A, Oliveira SM, Pitman NCA, Jorgensen PM, Salomão RP (2016) The discovery of the Amazonian tree flora with an update checklist of all known tree taxa. Scientific Reports 6(29549):1-15.

Species	f_c0,k (MPa)	f_t0,k (MPa)	f_v0,k (MPa)
Cambará Rosa (CR)	27.0	31.9	11.9
Cedro Amazonense (CA)	46.4	64.4	13.2
Guarucaia (Ga)	55.7	64.0	18.0
Cupiúba (Cup)	65.6	63.1	10.8
Roxinho (Ro)	81.2	68.0	15.8

Species	f_c0,k (MPa)	f_t0,k (MPa)	f_v0,k (MPa)
Cambará Rosa (CR)	26.4 (N)	26.5 (N)	10.6 (N)
Cedro Amazonense (CA)	41.9 (N)	53.8 (N)	11.6 (N)
Guarucaia (Ga)	55.8 (N)	46.9 (L)	9.6 (N)
Cupiúba (Cup)	52.3 (N)	54.5 (N)	14.7 (N)
Roxinho (Ro)	73.2 (N)	48.2 (N)	14.8 (L)

Species
Common name	Abbreviation	Scientific name
Cambará Rosa	CR	Erisma uncinatum Warm, Vochysiaceae
Cedro Amazonense	CA	Cedrelinga catenaeformis
Guarucaia	Ga	Parapiptadenia rigida
Cupiúba	Cup	Goupia glabra Aubl., Goupiaceae
Roxinho	Ro	Peltogyne spp.