Abstract
In order to locate a reasonable heating system, the austenite grain growth behavior of Nb microalloyed medium carbon steel has been experimentally studied at various austenitizing temperatures and for different holding times. It is indicated that austenite grain growth increases with increasing austenitizing temperatures and holding times. Particularly when the austenitizing temperature was above 1100 °C, austenite grains grew rapidly, and an abnormal austenite grain growth was observed. When the austenitizing temperature was lower than 1100 °C, austenite grain size and growth rate were small. The activation energy of grain growth in the tested steel is 397 679.5 J/mol. To ensure an absence of coarse grains in microstructures, the heating technology of the tested steel should be controlled for 1 h at 1100 °C. The relationships of austenite average grain size with soaking temperature and time of tested steel were obtained by mathematical calculation, and austenite average grain size was found to be in agreement with the measured size for different holding times.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Beck, P.A., Kremer, J.C., Demer, L.J., 1948. Grain growth in high purity aluminum and in aluminum-magnesium alloy. Transaction of American Institute of Mining, Metallurgical, and Petroleum Engineers, 175:372.
Gavard, L., Montheillet, F., Coze, L.J., 1998. Recrystallization and grain growth in high purity austenitic stainless steels. Scripta Materialia, 39(8):1095–1099. [doi:10.1016/S1359-6462(98)00276-0]
Jiao, S., Penning, J., Leysen, F., Houbaert, Y., Aernoudt, E., 2000. The modeling of the grain growth in a continuous reheating process of a low carbon Si-Mn bearing TRIP steel. ISIJ International, 40(10):1035–1040. [doi:10. 2355/isijinternational.40.1035]
Matsuura, K., Itoh, Y., 1991. Analysis of the effect of grain size distribution on grain growth by computer simulation. ISIJ International, 31(4):366–371. [doi:10.4028/www.scientific.net/MSF.94-96.331]
Lifshitz, I.M., Slyozov, V.V., 1961. The kinetics of precipitation from supersaturated solid solution. Journal of Physics and Chemistry of Solids, 9:35–50. [doi:10.1016/0022-3697(61)90054-3]
Liu, W., 2004. Effect of heating temperature on solid solution precipitation of second phase particles and grain growth. Wide and Heavy Plate, 10(2):24–27 (in Chinese).
Manohar, P.A., Dunne, D.P., Chandra, T., Killmore, C.R., 1996. Grain growth predictions in microalloyed steels. ISIJ International, 36(2):194–200. [doi:10.2355/isijinter national.36.194]
Nordberg, H., Aronsson, B., 1968. Solubility of niobium carbide in austenite. Journal of the Iron and Steel Institute, 12:1263–1266.
Uhm, S., Moon, J., Lee, C., Yoon, J., Lee, B., 2004. Prediction model for the austenite grain size in the coarse grained heat affected zone of Fe-C-Mn steels: considering the effect of initial grain size on isothermal growth behavior. ISIJ International, 44(7):1230–1237. [doi:10.2355/isijinter national.44.1230]
Sellars, C.M., Whiteman, J.A., 1979. Recrystallization and grain growth in hot rolling. Metal Science, 13(3–4):187–194.
Xue, R.D., Zhao, Z.Y., Xie, J.X., Li, X.E., 2007. Effect of heating temperature on morphology and composition of undissolved particles in high strength steel containing Ti-Nb. Journal of Iron and Steel Research, 19(4):80–84 (in Chinese).
Yu, Q.B., Sun, Y., 2006. Abnormal growth of austenite grain of low-carbon steel. Materials Science and Engineering A, 420(1):34–38. [doi:10.1016/j.msea.2006.01.027]
Zener, C., 1948. Grain, phases and interface: an interpretation of microstructure. Transaction of American Institute of Mining, Metallurgical, and Petroleum Engineers, 175: 15–51.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhao, Yl., Shi, J., Cao, Wq. et al. Kinetics of austenite grain growth in medium-carbon niobium-bearing steel. J. Zhejiang Univ. Sci. A 12, 171–176 (2011). https://doi.org/10.1631/jzus.A1000150
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1631/jzus.A1000150