Manufacturing Technology 2018, 18(1):165-169 | DOI: 10.21062/ujep/72.2018/a/1213-2489/MT/18/1/165

Influences of Friction Condition and End Shape of Billet on Convex at Root of Spline by Rolling with Round Dies

Da-Wei Zhang, Sheng-Dun Zhao
School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an 710049, P. R. China

The rolling process is widely used to manufacture high-performance splined shaft components. However, there is a convex at root on free end of spline formed by rolling with round dies. However, the analysis and representation of this forming problem are difficulty due to the complexity of motion and multiplicity of processing parameters. This paper concentrates on the corner filling problem, and a physical analog experiment was designed to investigate the problem. The physical experimental results indicated that the designed experiment can reflect the formation of convex during spline rolling process. The finite element analysis of the physical analog experiment process was carried out to study the influences of friction condition and end shape of billet on convex at root of rolled spline. The results indicated that the height of convex will be reduced with increasing friction condition; the height of convex can be reduced by optimizing the end shape of billet. The results of present study provide a basis for optimizing and controlling the forming quality on free end during spline rolling process.

Keywords: Spline, Rolling, Convex at root, Friction condition, End shape

Published: February 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Zhang D, Zhao S. Influences of Friction Condition and End Shape of Billet on Convex at Root of Spline by Rolling with Round Dies. Manufacturing Technology. 2018;18(1):165-169. doi: 10.21062/ujep/72.2018/a/1213-2489/MT/18/1/165.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. POKOVÁ, M.©., CIESLAR, M., ZIMINA, M. (2015). Grain refinement in Al-Mn-Fe-Si alloy by severe plastic deformation. In: Manufacturing Technology, Vol. 15 No. 4, pp. 679-684. J.E. Purkyne University. Czech Republic. Go to original source...
    2. PRÙ©A, F., BERNATIKOVÁ, A., PALAN, J. (2017). Ultra-high strength Ti grade 4 prepared by intensive plastic deformation. In: Manufacturing Technology, Vol. 17, No. 5, pp. 819-822. J.E. Purkyne University. Czech Republic.
    3. MIAO, H., MEI, Q., YUAN, J., ZHANG, S., JIN, Y., ZUO, D. (2017). Numerical simulation and experimental research on cold form tapping process of internal thread. In: Manufacturing Technology, Vol. 17, No. 4, pp. 519-526. J.E. Purkyne University. Czech Republic. Go to original source...
    4. JIA, Z., HAN, Z.R., PENG, W.F. (2015). Numerical study on effect of narrow groove on hot bearing ring rolling process. In: Manufacturing Technology, Vol. 15, No. 3, pp. 350-357. J.E. Purkyne University. Czech Republic. Go to original source...
    5. MASHEKOVA, A., NURTAZAEV, A., MASHEKOV, S., ALSHYNOVA, A. TUSSUPKALIYEVA, E. (2017). The influence of the technological parameters of rolling in the helical rollers and longitudinal wedge mill on the quality of two-phase titanium alloy. In: Manufacturing Technology, Vol. 17, No. 3, pp. 347-354. J.E. Purkyne University. Czech Republic. Go to original source...
    6. NEUGEBAUER, R., PUTZ, M., HELLFRITZSCH U. (2007). Improved Process Design and Quality for Gear Manufacturing with Flat and Round Rolling. In: Annals of CIRP Manufacture technology, Vol. 56, No. 1, pp. 307-312. Elsevier USA. United States. Go to original source...
    7. ZHANG, D.W., LI, Y.T., FU, J.H., ZHENG, Q.G. (2007). Mechanics analysis on precise forming process of external spline cold rolling. In: Chinese Journal of Mechanical Engineering, Vol. 20, No. 3, pp. 54-58. Chinese Mechanical Engineering Society. China. Go to original source...
    8. ZHANG, D.W., LI, Y.T., FU, J.H., ZHENG, Q.G. (2009). Rolling Force and Rolling Moment in Spline Cold Rolling Using Slip-line field Method. In: Chinese Journal of Mechanical Engineering, Vol. 22, No. 5, pp. 688-695. Chinese Mechanical Engineering Society. China. Go to original source...
    9. ZHANG, D.W., ZHAO S.D., LI Y.T. (2014). Rotatory condition at initial stage of external spline rolling. In: Mathematical Problem in Engineering, Vol. 2014, Article ID 363184. Hindawi Publishing Corporation. United States. Go to original source...
    10. NEUGEBAUER R., KLUG D., HELLFRITZSCH U. (2007). Description of the interactions during gear rolling as a basis for a method for the prognosis of the attainable quality parameters. In: Production Engineering Research and Development, Vol. 1, No. 3, pp. 253-257. Springer Verlag. Germany. Go to original source...
    11. ZHANG, D.W., ZHAO S.D., OU H. (2016). Motion Characteristic between die and workpiece in spline rolling process with round dies. In: Advances in Mechanical Engineering, 8(7): 1-12. SAGE. Uinted States. Go to original source...
    12. SONG J.L., LIU Z.Q., LI Y.T. (2017). Cold Rolling Precision Forming of Shaft Parts: Theory and Technologies, pp. 116-122. Springer-Verlag, Heidelberger Berlin. Go to original source...
    13. ZHANG, D.W., ZHAO S.D. (2016). Deformation characteristic of thread and spline synchronous. In: International Journal of Advanced Manufacturing Technology, Vol. 87, pp. 835-851. Springer Lodon. United Kingdom. Go to original source...
    14. LI Y.T., SONG J.L., ZHANG, D.W., ZHENG, Q.G. (2008). Mechanics analysis and numerical simulation on the precise forming process of spline cold rolling. In: Materials Science Forum, Vol. 575-578, pp. 416-421. Trans Tech Publications. Switzerland. Go to original source...
    15. ZHANG, D.W. (2007). Theoretical research on process of spline cold rolling (M.S. Thesis), pp. 82-83.Taiyuan University of Science and Technology, Taiyuan. (in Chinese)
    16. ZHANG, D.W., CUI M.C., CAO M., BEN N.Y., ZHAO S.D. (2017) Determination of friciton conditions in cold-rolling process of shaft part by using incremental ring compression test. In: International Journal of Advanced Manufacturing Technology, Vol. 91, pp. 3823-3831. Springer Lodon. United Kingdom. Go to original source...
    17. LI Y.Y., HU C.R. (2005). Experiment Design and Data Processing, pp. 203-214. Chemical Industry Press, Beijing. (in Chinese)
    18. TAGUCHI G. (1987). System of Experiment design (D. Clausing, translated), pp. 5-12. Kraus International Publications, New York.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content