Acta Mechanica Slovaca 2015, 19(4):50-55 | DOI: 10.21496/ams.2015.032
Waste Material Recyclation in Abrasive Water Jet Technologies
- Technical university of Košice, Faculty of Mechanical Engineering, Department of Process and Environmental Engineering
Recycling as a waste process technology is preferred in terms of environmental protection, today. Water jet technology is friendly and belongs to green technology. It is possible to divide as the paper material to the steel and can be divided into two principal groups described in the contribution. This progressive technology is applied in various sectors of industry. During the cutting operations creates the waste in the forms as polluted water, sludge, used abrasive material and other rest material from the semi- products. This contribution focuses on one type of waste - water. Water is an essential parameter in the process of water jet cutting machine and abrasive water jet machine. Water treatment takes place in filtration equipment, where the basic apparatus is filter. In the contribution is discussed several possibilities of recycling facilities, not only based on filtering. There were tested the water samples, taken from the process before and after the process. The composition of the water before cutting and after cutting operation were discussed and were compared the quality of water after recycling.
Keywords: Recycling, water jet technology, machine, filter, water
Published: October 31, 2015 Show citation
References
- Kmec, J., Gombár, M., Bičejová, Ľ., Dobrovič, J. (2011) Faktory hydroerózie. TU SjF Košice, p. 216
- Hires, O., Hatala, M., Hloch, S. (2007) Delenie kovových materiálov okružnou pílou, vodným prúdom a plazmovým oblúkom. Ostrava 2007, p.147
- Kmec, J., Kučerka, D., Gombár, M., Hrmo, R., Bičejová, Ľ. (2014) Delenie materiálu. TU SjF Košice, p. 287
- Salesmen presentation; KMT GmbH∙KMT Waterjet System: KMT Creating value through precision,15slyde, Germany, p. 77
- Kmec, J., Bičejová, Ľ., Nováková, M., Gombár, M. (2011) Rozdelený vodný lúč pre rezanie nerezových materiálov. TUKE, FVT Prešov, p. 143
- Kmec, J., Sobotová, L. (2010) Vodný lúč 25 rokov na Slovensku. Transfer inovácií, 18/2010, TU SjF Košice. pp.160-164
- Krajný, Z. (2013) Konštrukcia zariadení na obrábanie vysokotlakovým vodným lúčom WJM. Strojírenství, Industry central EU. from http://www.industry-central.eu/cs/clanky/strojírenství/105-kontrukcia-zariadeni-na-obrabanie-vysokotlakovym-vodnym-lucom-wjm, accessed on 2013-02-16
- Kopečný, L. (2011) Abrazívni vodní paprsek. VUT Brno, from https://dspace.vutbr.cz/bitstream/handle/11012/445/DIPLOMOV_PRACE-ABRAZIVN%C3%8D_VODNI_PAPRSEK-LIBOR_KOPECNY_2011.pdf?sequence=1, accessed on 2012 - 10 - 11
- Tvaružek, M. (2012) Studie použití vodního paprsku. VUT Brno. from https://dspace.vutbr.cz/bitstream/handle/11012/5059/2012_DP_Tvaruzek_Martin_108046.pdf?sequence=2, accessed on 2012 - 10 - 11
- Karková, M., Sobotová, L. (2013) Abrazívne materiály využívané pri delení materiálov AWJ technológiou. Transfer inovácií. Vol.13 no. 25 (2013), pp. 146-149
- Karková, M., Sobotová, L. (2013) Recyklácia abrazívnych materiálov pri technológii AWJ - 2013. Trendy a inovatívne prístupy v podnikových procesoch. Conference Proceedings, TU Košice, pp. 1-7
- Spišák, E., Badida, M., Kmec,, J., Sobotová, L. (2011) Identification of Structure of Hydro-Erosion Operation. Acta Mechanica Slovaca. Vol. 15, no. 2, pp. 80-86
Go to original source... - Salesmen presentation. WARD Pro abrasive recycling system (2015), from http://www.wardjet.com/recycling
This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.