[1]
P. Groche, M. Henkelmann, P. Gotz, S. Berner, Cold rolled profiles for vehicle construction, Archives of Civil and Mechanical Engineering, 8 (2008) 31-38.
DOI: 10.1016/s1644-9665(12)60191-5
Google Scholar
[2]
P. Eggertsen, K. Mattiasson, On the modelling of the bending-unbending behaviour for accurate springback predictions, International Journal of Mechanical Sciences, 51 (2009) 547-563.
DOI: 10.1016/j.ijmecsci.2009.05.007
Google Scholar
[3]
D. Fei, P. Hodgson, Experimental and numerical studies of springback in air v-bending process for cold rolled TRIP steels, Nucl Eng Des, 236 (2006) 1847-1851.
DOI: 10.1016/j.nucengdes.2006.01.016
Google Scholar
[4]
J. Mendiguren, Experimental and numerical analysis of the elastic behaviour of the TRIP 700 steel for springback predictions, in, Mondragon Unibertsitatea, 2012, p.141.
Google Scholar
[5]
L.J. deVin, A.H. Streppel, U.P. Singh, H.J.J. Kals, A process model for air bending, Journal of Materials Processing Technology, 57 (1996) 48-54.
DOI: 10.1016/0924-0136(95)02043-8
Google Scholar
[6]
F. Morestin, M. Boivin, C. Silva, Elasto plastic formulation using a kinematic hardening model for springback analysis in sheet metal forming, Journal of Materials Processing Technology, 56 (1996) 619-630.
DOI: 10.1016/0924-0136(95)01876-x
Google Scholar
[7]
M. Yang, Y. Akiyama, T. Sasaki, Evaluation of change in material properties due to plastic deformation, Journal of Materials Processing Technology, 151 (2004) 232-236.
DOI: 10.1016/j.jmatprotec.2004.04.114
Google Scholar
[8]
X.C. Li, Y.Y. Yang, Y.Z. Wang, J. Bao, S.P. Li, Effect of the material-hardening mode on the springback simulation accuracy of V-free bending, Journal of Materials Processing Technology, 123 (2002) 209-211.
DOI: 10.1016/s0924-0136(02)00055-9
Google Scholar
[9]
S. Chatti, N. Hermi, The effect of non-linear recovery on springback prediction, Comput Struct, 89 (2011) 1367-1377.
DOI: 10.1016/j.compstruc.2011.03.010
Google Scholar
[10]
F. Yoshida, T. Uemori, K. Fujiwara, Elastic-plastic behavior of steel sheets under in-plane cyclic tension-compression at large strain, Int J Plasticity, 18 (2002) 633-659.
DOI: 10.1016/s0749-6419(01)00049-3
Google Scholar
[11]
H.Y. Yu, Variation of elastic modulus during plastic deformation and its influence on springback, Mater Design, 30 (2009) 846-850.
DOI: 10.1016/j.matdes.2008.05.064
Google Scholar
[12]
M. Weiss, J. Marnette, P. Wolfram, J. Larranaga, P. Hodgson, Comparison of Bending of Automotive Steels in Roll Forming and in a V-Die, Key Engineering Materials, 504-506 (2012) 797-802.
DOI: 10.4028/www.scientific.net/kem.504-506.797
Google Scholar
[13]
J. Mendiguren, F. Cortes, L. Galdos, S. Berveiller, Strain path's influence on the elastic behaviour of the TRIP 700 steel, Mat Sci Eng a-Struct, 560 (2013) 433-438.
DOI: 10.1016/j.msea.2012.09.087
Google Scholar
[14]
A. Abvabi, B. Rolfe, J. Larrañaga, L. Galdos, C. Yang, M. Weiss, Using the Solid-shell Element to Model the Roll Forming of Large Radii Profiles, Steel research international: Proceedings of 14th International Conference on Metal Forming, (2012).
Google Scholar
[15]
MSC. Marc, Volume B: Element Library, MSC. Software Corporation, USA, (2010).
Google Scholar
[16]
K.P. Li, W.P. Carden, R.H. Wagoner, Simulation of springback, International Journal of Mechanical Sciences, 44 (2002) 103-122.
DOI: 10.1016/s0020-7403(01)00083-2
Google Scholar