Analyzing Process Capability of Drilling on Glass Fiber Reinforced Polyester (GFRP) Composites with Taguchi Loss Function

Haradhan Soren; Subhash Chandra Panja; Sunil Hansda; Simul Banerjee

doi:10.4028/www.scientific.net/AMR.622-623.1314

Paper Titles

Fabrication and Characterization of SiC, Al₂O₃ and B₄C Reinforced Al-Zn-Mg-Cu Alloy (AA 7075) Metal Matrix Composites: A Study
p.1295

Tribological Behaviour of Cu -5W Sintered Powder Composite
p.1300

Experimental Investigation on Prediction of Hole Quality Characteristics of Aluminum Matrix Composite (AMC225xe)
p.1305

Geocomposite Manufactured from PP Nonwoven/HDPE Geonet
p.1310

Analyzing Process Capability of Drilling on Glass Fiber Reinforced Polyester (GFRP) Composites with Taguchi Loss Function
p.1314

Mode I Fracture Toughness of Banana Fiber and Glass Fiber Reinforced Composites
p.1320

Analysis of Structures of Cementitious Composites with Recyclates and Dispersion Reinforcement of Polymer Fibres
p.1325

Visco-Elastic Properties of Catheter Reinforced with Braids: Stress Relaxation under Two-Stage Step Strain for Different Deformation Paths
p.1330

Mechanical Properties of Stirred SiC Reinforced Aluminium Alloy: Stir Casting with Different Composition of SiC, Blade Angle and Stirring Speed
p.1335

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 622-623Analyzing Process Capability of Drilling on Glass...

Analyzing Process Capability of Drilling on Glass Fiber Reinforced Polyester (GFRP) Composites with Taguchi Loss Function

Abstract:

The delamination is a major problem associated with the drilling of chopped glass fiber reinforced polyester (GFRP) composites. It reduces the structural integrity of the material, results in poor assembly tolerance and has the potential for long term performance deterioration. Thus it is important to evaluate the process capability of drilling on this material. It will thereby reveal the spectrum of delamination to be accepted from the view point of process capability for a chosen range of material thickness, drill diameter, speed and feed rate combinations. In the present analysis, therefore, Taguchi loss function is derived for the particular process based on the experimental data. Process capability index is then evaluated. The range of delamination factor is determined based on the consideration that process capability index should be one or more. The results are presented.

You might also be interested in these eBooks

Manufacturing Science and Technology III

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 622-623)

Pages:

1314-1319

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.622-623.1314

Citation:

Cite this paper

Online since:

December 2012

Authors:

Haradhan Soren, Subhash Chandra Panja, Sunil Hansda, Simul Banerjee

Keywords:

Glass Fiber Reinforced Polyester (GFRP) Composite, Process Capability Index, Taguchi Loss Functions

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

References

[1] Y.H. Guu, H. Hocheng, N.H. Tai and S.Y. Liu: Effect of electrical discharge machining on the characteristics of carbon fibre reinforced carbon compososities. Journal of material science. Vol. 36 (2001), p.2037-(2043).

Google Scholar

[2] E.I. Sonabaty, U.A. Khasaba, and T. Machaly: Factors affecting the machinability of GFR/epoxy composites. composite Structures. Vol. 63 (2004), pp.715-720.

DOI: 10.1016/s0263-8223(03)00181-8

Google Scholar

[3] E. Capello: Workpiece damping and its effects on delamination damage in drilling thin composite laminates. Journal of material processing Technology. Vol. 148 (2004), pp.186-195.

DOI: 10.1016/s0924-0136(03)00812-4

Google Scholar

[4] U.A. Khashaba: Delamination in drilling GFR-thermoset composites. Composite Structures Vol. 63 (2004), pp.313-327.

DOI: 10.1016/s0263-8223(03)00180-6

Google Scholar

[5] J.C. Rubio, A.M. Abrao, P.E. Faria, A.E. Correia and J.P. Davim: Effects of high speed in drilling of glass fiber reinforced plastic: Evaluation of the delamination factor. International journal of Machine Tools and Manufacture. Vol. 48 (2008).

DOI: 10.1016/j.ijmachtools.2007.10.015

Google Scholar

[6] H. Hocheng, C. Tsao: Comprehensive analysis of delamination in drilling of composite materials with various drill bits. Journal of Material Processing Technology. Vol. 140 (2003), pp.335-339.

DOI: 10.1016/s0924-0136(03)00749-0

Google Scholar

[7] N.S. Mohan, S.M. Kulkarni and A. Ramachandra: Delamination analysis in drilling process of glass fibre reinforced plastic (GFRP) composite materials. Journal of Material Processing Technology. Vol. 186 (2007), pp.265-271.

DOI: 10.1016/j.jmatprotec.2006.12.043

Google Scholar

[8] A. Bissel: How reliable is your capability index? Vol. 39 (1990), pp.331-340.

Google Scholar

[9] J.P. Chen and C.G. Ding: A new process capability index for non-normal distribution. Internation Journal of Quality and Reliability Management. 18(7) (2001), pp.762-770.

DOI: 10.1108/02656710110396076

Google Scholar

[10] B.P.K. Leung and F.A. Spiring: Some properties of the family of inverted probability loss function. Quality Technology and Quantitative Management. Vol. 1 (2004), pp.125-147.

DOI: 10.1080/16843703.2004.11673068

Google Scholar

[11] K.L. Hsieh and L.I. Tong: Incorporating process capability index and quality loss functionanalyzing, the process capability for qualitative data. International Journal of Advanced Manufacturing Technology. Vol. 27 (2006), pp.1212-1222.

DOI: 10.1007/s00170-004-2314-1

Google Scholar

[12] M. Abdolshah, M.Y.B. Ismail, R.M. Yusuff and T.S. Hong: A new technique to measure process capability with Taguchi loss functions. International Conference on Information Management and Engineering. (2009), pp.186-190.

DOI: 10.1109/icime.2009.123

Google Scholar

[13] M.S. Phadke: Quality engineering using robust design. Prentice Hall International. New Jersey, NJ, (1989).

Google Scholar