Effect of Cutting Parameters on Cutting Temperature of TiAl6V4 Alloy

S. Sulaiman; A. Roshan; S. Borazjani

doi:10.4028/www.scientific.net/AMM.392.68

Paper Titles

Tensile Properties and Fracture Toughness of Three Rubber-Modified Epoxies
p.46

A Study on the Effect of SiC Reinforcement on the Surface and Tribological Behavior on Al-Metal Matrix Composites
p.51

Improvement of Piezoelectric Property of Poly(Vinylidene Fluoride) Nanocomposites Using Multi-Walled Carbon Nanotubes
p.57

Friction and Wear Performance of CF/PTFE Composites in Water Lubrication
p.62

Effect of Cutting Parameters on Cutting Temperature of TiAl6V4 Alloy
p.68

Delamination Behaviour of Rubber-Toughened Carbon Fibre/Epoxy Composites
p.73

Development of a Manual Metal Arc Welding Flux from Local Raw Materials in Nigeria
p.78

CFD Investigation of Damper Plate Effect on Air Flow in High Speed Rotation Hard Disk Drive by Using K-E with a Partial Model
p.85

A New Analytical Expression of Overall Collision Efficiency for the Water Droplet Impinging on a Cylinder
p.90

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vol. 392Effect of Cutting Parameters on Cutting...

Effect of Cutting Parameters on Cutting Temperature of TiAl6V4 Alloy

Abstract:

A Finite Element Modeling (FEM) and Simulation was Used to Investigate the Effect of Tool Rake Angle, Cutting Speed and Feed Rate on the Cutting Temperature of Tial6v4 Alloy. the Purpose of this Study was to Find Proper Cutting Parameters for Machining of Titanium Alloy where Cutting Temperature was Lowest. A FEM Based on ABAQUS Software which Involves Jonson-Cook Material Model and Coulomb’s Friction Law was Applied to Simulate an Orthogonal Cutting Process. in this Simulation Work, a Range of Tool Rake Angle from 0° to 10°, a Range of Cutting Speed from 300 m/min to 600 m/min and a Range of Feed Rate between 0.1 Rev/mm and 0.25 Rev/mm were Investigated. the Simulation Results Indicated that Increase in Rake Angle Reduces Cutting Temperature while Increasing Cutting Speed and Feed Rate Increase the Cutting Temperature.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volume 392)

Pages:

68-72

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.392.68

Citation:

Cite this paper

Online since:

September 2013

Authors:

S. Sulaiman, A. Roshan, S. Borazjani

Keywords:

Finite Element Modeling (FEM), Rake Angle, Titanium Alloy

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

References

[1] L.T. Ginta, M.A. Lajis and A.K.M. Nurul Amin, American Journal of Engineering and Applied Sciences. 2 (2009)147-153.

Google Scholar

[2] S. I. Jaffery and P. T. Mativenga, Assessment of the machinability of Ti-6Al-4V alloy using the wear map approach, Intentional Journal of Advance Manufacturing Technology. 40 (2009) 687- 696.

DOI: 10.1007/s00170-008-1393-9

Google Scholar

[3] N. Andriya and S. Ghosh, Dry Machining of Ti-6Al-4V using PVD Coated TiAlN Tools, Proceedings of the World Congress on Engineering, London, UK, July 4-6 (2012).

Google Scholar

[4] A. H. Moaz, B. A. Khidhir, B. Mohamed and A. A. Oshkour, Prediction of High Cutting Speed Parameters for Ti-6Al-4V by Using Finite Element Modeling, International Journal of Modeling and Optimization. 2(2012).

DOI: 10.7763/ijmo.2011.v1.81

Google Scholar

[5] B. Davoodi and H. Hosseinzadeh, A new method for heat measurement during high speed machining, Measurement. 45 (2012) 2135-2140.

DOI: 10.1016/j.measurement.2012.05.020

Google Scholar

[6] G.G. Ye, S.F. Xue, X.H. Tong and L.H. Dai, Influence of cutting conditions on the cutting performance of TiAl6V4, Advanced Materials Research. 337 (2011) 387-391.

DOI: 10.4028/www.scientific.net/amr.337.387

Google Scholar

[7] G. R. Johnson and W. H. Cook, Fracture characteristics of three metals subjected to various strain, strain rates, temperature and pressure, Eng. Frac. Mech. 2/1 (1985) 31-48.

DOI: 10.1016/0013-7944(85)90052-9

Google Scholar

[8] J.P. Davim and C. Maranhao, A study of plastic strain and plastic strain rate in machining of steel AISI 1045 using FEM analysis, Materials and Design. 30 (2009) 160-165.

DOI: 10.1016/j.matdes.2008.04.029

Google Scholar

[9] G. Chen, C. Ren, X. Yang, X. Jin, T. Guo, Finite element simulation of high-speed machining of titanium alloy (Ti–6Al–4V) based on ductile failure model, Intentional Journal of Advance Manufacturing Technology. 56 (2011) 1027-1038.

DOI: 10.1007/s00170-011-3233-6

Google Scholar

[10] T. Ozel and E. Zeren, Finite Element Modeling of Stresses Induced by High Speed Machining With Round Edge Cutting Tools, International Mechanical Engineering Congress and Exposition, Orlando, Florida, November 5-10 (2005).

DOI: 10.1115/imece2005-81046

Google Scholar

[11] C.Z. Duan , T. Dou, Y.J. Cai and Y.Y. Li, Finite Element Simulation and Experiment of Chip Formation Process during High Speed Machining of AISI 1045 Hardened Steel, International Journal of Recent Trends in Engineering. 1 (2009) 46-50.

DOI: 10.1109/iccet.2010.5486196

Google Scholar

[12] A. Devillez, S. Lesko, and W. Mozerc, Cutting tool crater wear measurement with white light interferometry. Wear 256(2004) 56–65.

DOI: 10.1016/s0043-1648(03)00384-3

Google Scholar

[13] M. C. Shaw, Metal cutting principles, Oxford University, press, London, (1984).

Google Scholar