Paper Titles

Optimization of EBW Parameters for 2219 AL-Alloy Using Grey Relation Method
p.507

Study on the Wetting Device of GMS-7 Spine Taping Machine
p.515

Research Advance on the Drying Section of Paper Machine
p.520

Modeling and Stability Analysis of SiCp/Al Composites Thin-Walled Workpiece in Rotary Ultrasonic Machining
p.527

Micromechanical Modelling of Elliptic Vibration-Assisted Cutting of Unidirectional FRP Composites
p.531

Dynamic Simulation on Feedwater Heater of Nuclear Power Plant
p.535

Steady-State Load Analysis of a Caterpillar Chassis by Finite Element Method
p.541

Safety Inventory under a Periodic Review System
p.545

Analysis on Crack Propagation of Roll by the Finite-Element
p.553

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 591-593Micromechanical Modelling of Elliptic...

Micromechanical Modelling of Elliptic Vibration-Assisted Cutting of Unidirectional FRP Composites

Article Preview

Abstract:

Fibre-reinforced polymer (FRP) composites have been widely used in industry. However, the machining of FRP products is difficult, because of very different properties of the fibres and matrix. This paper discusses the development and implementation of a microstructure-based three-dimensional finite element model for the elliptic vibration-assisted (EVA) cutting of unidirectional FRP composites. The results showed that the EVA cutting has a good potential to the machining of FRP composites, featured a much reduced cutting force, better surface integrity and controllable chip size.

You might also be interested in these eBooks

Manufacturing Engineering and Automation II

Info:

Periodical:

Advanced Materials Research (Volumes 591-593)

Pages:

531-534

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.591-593.531

Citation:

Cite this paper

Online since:

November 2012

Authors:

Wei Xing Xu, Liang Chi Zhang, Yong Bo Wu

Keywords:

Fiber-Reinforced Composites, Micromechanical Model, Vibration-Assisted Cutting

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

[1] L.C. Zhang: J. Mater. Process. Technol. Vol. 209 (2009), p.4548

[2] X.M. Wang and L.C. Zhang: Int. J. Mach. Tools Manuf. Vol. 43 (2003), p.1015

[3] H. Zhang, W. Chen, D. Chen and L.C. Zhang: Key Eng. Mater. Vol. 196 (2001), p.43

[4] L.C. Zhang, H. Zhang and X.M. Wang: Mach. Sci. Technol. Vol. 5 (2001), p.293

[5] N.S. Hu and L.C. Zhang: J. Mater. Process. Technol. Vol. 152 (2004), p.333

[6] N.S. Hu and L.C. Zhang: J. Mater. Process. Technol. Vol. 140 (2003), p.152

[7] G. Venu Gopala Rao, P. Mahajan and N. Bhatnagar: Compos. Sci. Technol. Vol. 67 (2007), p.579

[8] K.A. Calzada, S.G. Kapoor, R.E. DeVor, J. Samuel and A.K. Srivastava: J. Manuf. Process. Vol. 14 (2012), p.141

[9] G. Venu Gopala Rao, P. Mahajan and N. Bhatnagar: Compos. Sci. Technol. Vol. 67 (2007), p.2271

[10] M. Mahdi and L.C. Zhang: J. Mater. Process. Technol. Vol. 113 (2001), p.373

[11] M. Mahdi and L.C. Zhang: J. Mater. Process. Technol. Vol. 113 (2001), p.368

[12] D. Arola and M. Ramulu: Int. J. Mech. Sci. Vol. 39 (1997), p.597

[13] M.V. Ramesh, K.N. Seetharamu, N. Ganesan and M.S. Sivakumar: Int. J. Mach. Tools Manuf. Vol. 38 (1998), p.1531

[14] Y. Peng, Z. Liang, Y. Wu, Y. Guo and C. Wang: Int. J. Adv. Manuf. Tech. Vol. 59 (2012), P.67

[15] L.C. Zhang: J. Mater. Process. Technol. Vol. (1999), p.273

[16] ABAQUS Handbook, Version 5.4 (Hibbitt, Karlsson & Sorensen, Inc., USA 2008).

[17] D. Nayak and N. Bhatnagar: Mach. Sci. Technol. Vol. 9 (2005), p.503

[18] C. Ma, E. Shamoto, T. Moriwaki and L. Wang: Int. J. Mach. Tools Manuf. Vol. 44 (2004), p.1305