nach oben

Erschienen in:

2018 | OriginalPaper | Buchkapitel

10. Metal Matrix Composite Coatings by Cold Spray

verfasst von : Min Yu, Wenya Li

Erschienen in: Cold-Spray Coatings

Verlag: Springer International Publishing

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Cold spray is a relatively easy and economical approach to deposit composite coatings with comparable or even better properties than other processing methods. This article summarized the published papers on cold-sprayed metal matrix composite coatings. After a brief introduction of the remarkable advantage of cold spray in fabricating composite and the building-up process of the cold-sprayed composite coating, the versatility of cold spray to produce a great wide range of applicable materials was classified according to the matrix materials, i.e., aluminum, copper, nickel, tungsten carbide, titanium, hydroxyapatite, and polymer. Then, some key issues concerning the content loss and fragmentation of the hard particles were put forward, and post-spray treatment techniques and powder preparations were thus concluded.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Vorheriges Kapitel Cold-Sprayed Metal Matrix Composite Coatings

Nächstes Kapitel Tribological Coatings Prepared by Cold Spray

Aggarwal G (2007) Development of self-lubricating coatings via cold spray process: feedstock formulation and deformation modeling. Dissertation, The Pennsylvania State University

Aldwell B, Yin S, McDonnell KA, Trimble D, Hussain T, Lupoi R (2016) A novel method for metal-diamond composite coating deposition with cold spray and formation mechanism. Scrip Mater 115:10–13CrossRef

Assadi H, Kreye H, Gartner F, Klassen T (2016) Cold spraying -a materials perspective. Acta Mater 116:382–407CrossRef

Bakshi SR, Singh V, Balani K, McCartney DG, Seal S, Agarwal A (2008) Carbon nanotube reinforced aluminum composite coating via cold spraying. Surf Coat Technol 202(21):5162–5169CrossRef

Boyer RR (1996) An overview on the use of titanium in the aerospace industry. Mater Sci Eng A 213(1–2):103–114CrossRef

Bu H, Yandouzi M, Lu C, MacDonald D, Jodoin B (2012) Cold spray blended Al + Mg₁₇Al₁₂ coating for corrosion protection of AZ91D magnesium alloy. Surf Coat Technol 207:155–162CrossRef

Chen H, Pala Z, Hussain T, McCartney DG (2017) Fabrication and microstrain evolution of Al-TiB₂ composite coating by cold spray deposition. In: Proceedings of the institution of mechanical engineers, Part L: Journal of Materials: Design and Applications, pp 1–9

Cherigui M, Li W, Hamzaoui R, Ji V, Fenineche N, Coddet C (2008) Microstructure and magnetic properties of FeSiBNbCu-Al cold spray coatings. Eur Phys J Appl Phys 43(1):79–86CrossRef

Cho S, Takagi K, Kwon H, Seo D, Ogawa K, Kikuchi K, Kawasaki A (2012) Multi-walled carbon nanotube-reinforced copper nanocomposite coating fabricated by low-pressure cold spray process. Surf Coat Technol 206(16):3488–3494CrossRef

Cinca N, List A, Gartner F, Guilemany JM, Klassen T (2014) Influence of spraying parameters on cold gas spraying of iron aluminide intermetallics. Surf Coat Technol 268:99–107CrossRef

Dong H, Bell T (2000) Enhanced wear resistance of titanium surfaces by a new thermal oxidation treatment. Wear 238(2):131–137CrossRef

Feng C, Guipont V, Jeandin M, Amsellem O, Pauchet F, Saenger R, Bucher S, Iacob C (2012) B₄C/Ni composite coatings prepared by cold spray of blended or CVD-coated powders. J Therm Spray Technol 21(3–4):561–570CrossRef

Gao P-H, Li Y-G, Li C-J, Yang G-J, Li C-X (2008) Influence of powder porous structure on the deposition behavior of cold-sprayed WC-12Co coatings. J Therm Spray Technol 17(5–6):742–749CrossRef

Godet M (1984) The third-body approach: a mechanical view of wear. Wear 100(1):437–452CrossRef

Gschneidner KA, Beaudry BJ, Capellen J (2001) Properties and selection: nonferrous alloys and special-purpose materials. ASM International, Book News, Inc., Portland, OR, pp 889–896

Guo X, Chen J, Yu H, Liao HL, Coddet C (2016) A study on the microstructure and tribological behavior of cold-sprayed metal matrix composites reinforced by particulate quasicrystal. Surf Coat Technol 268:94–98CrossRef

Heimann RB, Kleiman JI, Litovsky E, Marx S, Ng R, Petrov S, Shagalov M, Sodhi RNS, Tang A (2014) High-pressure cold gas dynamic (CGD)-sprayed alumina-reinforced aluminum coatings for potential application as space construction material. Surf Coat Technol 252:113–119CrossRef

Hodder KJ, Izadi H, McDonald AG, Gerlich AP (2012) Fabrication of aluminum-alumina metal matrix composites via cold gas dynamic spraying at low pressure followed by friction stir processing. Mater Sci Eng A 556:114–121CrossRef

Hodder KJ, Nychka JA, McDonald AG (2014) Comparison of 10 um and 20 nm Al-Al₂O₃ metal matrix composite coatings fabricated by low-pressure cold gas dynamic spraying. J Therm Spray Technol 23(5):839–848CrossRef

Hu HX, Jiang SL, Tao YS, Xiong TY, Zheng YG (2011) Cavitation erosion and jet impingement erosion mechanism of cold sprayed Ni-Al₂O₃ coating. Nuclear Eng Design 241(12):4929–4937CrossRef

Huang C, Li W, Zhang Z, Planche MP, Liao H and Montavon G (2016) Effect of tool rotation speed on microstructure and microhardness of friction-stir-processed cold-sprayed SiC_p/Al5056 composite coating. J Therm Spray Technol 25(7):1–8

Huang C, Li W, Planche M-P, Liao H, Montavon G (2017) In-situ formation of Ni-Al intermetallics-coated graphite/Al composite in a cold-sprayed coating and its high temperature tribological behaviors. J Mater Sci Tech. https://doi.org/10.1016/j.jmst.2017.01.026

Irissou E, Legoux J-G, Arsenault B, Moreau C (2007) Investigation of Al-Al2O3 cold spray coating formation and properties. J Therm Spray Technol 16(5–6):661–668CrossRef

Kang N, Coddet P, Liao H, Coddet C (2015a) The effect of heat treatment on microstructure and tensile properties of cold spray Zr base metal glass/Cu composite. Surf Coat Technol 280:64–71CrossRef

Kang K, Park H, Kim J, Lee C (2015b) Role of spray processes on microstructural evolution, and physical and mechanical properties of multi-walled carbon nanotube reinforced cu composite coatings. Appl Surf Sci 356:1039–1051CrossRef

Kang K, Kim J, Park H, Lee C (2016) Formation and heat treatment of kinetic sprayed nanocrystalline al coatings reinforced with multi-walled carbon nanotubes: the relationship between microstructural features and physical properties. Surf Coat Technol 289:124–135CrossRef

Khun NW, Li RT, Loke K, Khor KA (2015) Effects of Al-Cr-Fe Quasicrystal content on Tribological properties of cold-sprayed titanium composite coatings. Tribol T 58:616–624CrossRef

Kim H-J, Lee C-H, Hwang S-Y (2005) Superhard nano WC-12%Co coating by cold spray deposition. Mater Sci Eng A 391(1–2):243–248

Kim HJ, Jang JH, Chang HL (2007) Assessment of metal/diamond composite coating by cold spray deposition. J Korean Inst Metals Mater 45(7):409–415

Koivuluoto H, Vuoristo P (2010a) Effect of powder type and composition on structure and mechanical properties of Cu+Al₂O₃ coatings prepared by using low-pressure cold spray process. J Therm Spray Technol 19(5):1081–1092CrossRef

Koivuluoto H, Vuoristo P (2010b) Structural analysis of cold-sprayed nickel-based metallic and metallic-ceramic coatings. J Therm Spray Technol 19(5):975–989CrossRef

Koivuluoto H, Milanti A, Bolelli G, Lusvarghi L, Vuoristo P (2014) High-pressure cold-sprayed Ni and Ni-Cu coatings: improved structures and corrosion properties. J Therm Spray Technol 23(1):98–103CrossRef

Lashgari HR, Sufizadeh AR, Emamy M (2010) The effect of strontium on the microstructure and wear properties of A356-10%B₄C cast composites. Mater Design 31(4):2187–2195CrossRef

Lee HY, Jung SH, Lee SY, Ko KH (2007) Alloying of cold-sprayed Al-Ni composite coatings by post-annealing. Appl Surf Sci 253(7):3496–3502CrossRef

Lee KA, Jung DJ, Park DY, Kang WG, Lee JK, Kim HJ (2009) Study on the fabrication and physical properties of cold-sprayed, Cu-based amorphous coating. J Phys Conf Ser 144:012113CrossRef

Li WY, Zhang G, Guo X, Liao H, Coddet C (2007) Characterizations of cold-sprayed TiN particle-reinforced Al alloy-based composites – from structures to tribological behaviour. Adv Eng Mater 9(7):577–583CrossRef

Li WY, Zhang G, Liao HL, Coddet C (2008a) Characterizations of cold sprayed TiN particle reinforced Al2319 composite coating. J Mater Process Technol 202(1–3):508–513CrossRef

Li W-Y, Zhang C, Liao H, Li J, Coddet C (2008b) Characterizations of cold-sprayed nickel-alumina composite coating with relatively large nickel-coated alumina powder. Surf Coat Technol 202(19):4855–4860CrossRef

Li WY, Zhang G, Zhang C, Elkedim O, Liao H, Coddet C (2008c) Effect of ball milling of feedstock powder on microstructure and properties of TiN particle-reinforced Al alloy-based composites fabricated by cold spraying. J Therm Spray Technol 17(3):316–322CrossRef

Li WY, Yang C, Liao H (2011) Effect of vacuum heat treatment on microstructure and microhardness of cold-sprayed TiN particle-reinforced Al alloy-based composites. Mater Design 32(1):388–394CrossRef

Li W, Huang C, Yu M, Liu D, Feng Y, Liao H (2014) Investigation of high temperature oxidation behavior and tribological performance on cold sprayed nickel-alumina composite coating. Surf Coat Technol 239:95–101CrossRef

Liu Y, Dang Z, Wang Y, Huang J, Li H (2014a) Hydroxyapatite/graphene-nanosheet composite coatings deposited by vacuum cold spraying for biomedical applications: inherited nanostructures and enhanced properties. Carbon 67:250–259CrossRef

Liu Y, Huang J, Li H (2014b) Nanostructural characteristics of vacuum cold-sprayed hydroxyapatite/graphene-nanosheet coatings for biomedical applications. J Therm Spray Technol 23(7):1149–1156CrossRef

Long M, Rack HJ (1998) Titanium alloys in total joint replacement – a materials science perspective. Biomaterials 19(19):1621–1639CrossRef

Luo XT, Li CJ (2012) Thermal stability of microstructure and hardness of cold-sprayed cBN/NiCrAl nanocomposite coating. J Therm Spray Technol 21(3):578–585CrossRef

Luo X-T, Yang G-J, Li C-J (2011) Multiple strengthening mechanisms of cold-sprayed cBNp/NiCrAl composite coating. Surf Coat Technol 205(20):4808–4813CrossRef

Luo XT, Yang EJ, Shang FL, Yang GJ, Li CX, Li CJ (2014) Microstructure, mechanical properties, and two-body abrasive wear behavior of cold-sprayed 20vol.% cubic BN-NiCrAl nanocomposite coating. J Therm Spray Technol 23(7):1181–1190CrossRef

Maestracci R, Sova A, Jeandin M, Malhaire JM, Movchan I, Bertrand P, Smurov I (2016) Deposition of composite coatings by cold spray using stainless steel 316L, copper and Tribaloy T-700 powder mixtures. Surf Coat Technol 287:1–8CrossRef

Melendez NM, McDonald AG (2013) Development of WC-based metal matrix composite coatings using low-pressure cold gas dynamic spraying. Surf Coat Technol 214:101–109CrossRef

Melendez NM, Narulkar VV, Fisher GA, McDonald AG (2013) Effect of reinforcing particles on the wear rate of low-pressure cold-sprayed WC-based MMC coatings. Wear 306(1–2):185–195CrossRef

Meydanoglu O, Jodoin B, Kayali ES (2013) Microstructure, mechanical properties and corrosion performance of 7075 Al matrix ceramic particle reinforced composite coatings produced by the cold gas dynamic spraying process. Surf Coat Technol 235:108–116CrossRef

Mirazimi J, Abachi P, Purazrang K (2016) Spark plasma sintering of ultrafine YSZ reinforced cu matrix functionally graded composite. Acta Metall Sin 29(12):1–8CrossRef

Na H, Bae G, Shin S, Kumar S, Kim H, Lee C (2009) Advanced deposition characteristics of kinetic sprayed bronze/diamond composite by tailoring feedstock properties. Compos Sci Technol 69(3–4):463–468CrossRef

Novoselova T, Celotto S, Morgan R, Fox P, ONeill W (2007) Formation of TiAl intermetallics by heat treatment of cold-sprayed precursor deposits. J Alloy Compd 436(1–2):69–77CrossRef

Paksoy AH, Deprem O, Tazegul O, Cimenoglu H (2016) Tribology of SiCp reinforced Al-12Si matrix composite coatings in water. Tribo Int. https://doi.org/10.1016/j.triboint.2016.10.037

Pialago EJT, Kwon OK, Kim M-S, Park CW (2015a) Ternary Cu-CNT-AlN composite coatings consolidated by cold spray deposition of mechanically alloyed powders. J Alloy Compd 650:199–209CrossRef

Pialago EJT, Kwon OK, Park CW (2015b) Cold spray deposition of mechanically alloyed ternary Cu-CNT-SiC composite powders. Ceram Int 41(5, Part B):6764–6775CrossRef

Pialago EJT, Kwon OK, Jin JS, Park CW (2016) Nucleate pool boiling of R134a on cold sprayed Cu-CNT-SiC and Cu-CNT-AlN composite coatings. Appl Therm Eng 103:684–694CrossRef

Price TS, Shipway PH, McCartney DG, Calla E, Zhang D (2007) A method for characterizing the degree of inter-particle bond formation in cold sprayed coatings. J Therm Spray Technol 16(4):566–570CrossRef

Ravi K, Ichikawa Y, Ogawa K, Deplancke T, Lame O, Cavaille J-Y (2016) Mechanistic study and characterization of cold-sprayed ultra-high molecular weight polyethylene-nano-ceramic composite coating. J Therm Spray Technol 25(1):160–169CrossRef

Rolland G, Sallamand P, Guipont V, Jeandin M, Boller E, Bourda C (2012) Damage study of cold-sprayed composite materials for application to electrical contacts. J Therm Spray Technol 21(5):758–772CrossRef

Sacks N (2016) Low pressure cold gas dynamic spraying of tungsten carbide-nickel coatings. Metal Powder Rep 71(5):356–358CrossRef

Sansoucy E, Marcoux P, Ajdelsztajn L, Jodoin B (2008) Properties of SiC-reinforced aluminum alloy coatings produced by the cold gas dynamic spraying process. Surf Coat Technol 202(16):3988–3996CrossRef

Segall AE, Smid I, Walia P, Eden TJ (2008) Self-lubricating coatings for elevated temperature applications using a high-velocity-particle-consolidation (hvpc) process. AFRL-RX-WP-TR-2008-4380

Sevillano F, Poza P, Munez CJ, Vezzu S, Rech S, Trentin A (2013) Cold-sprayed Ni-Al 2 O 3 coatings for applications in power generation industry. J Therm Spray Technol 22(5):772–782CrossRef

Shen L, Kong L-y, Xiong T-y, Du H, Li T-f (2009) Preparation of TiAl3-Al composite coating by cold spraying. T Nonferr Metal Soc 19(4):879–882CrossRef

Shkodkin A, Kashirion A, Kulyuev O, Buzdygar T (2006) Metal particle deposition stimulation by surface abrasive treatment in gas dynamic spraying. J Therm Spray Technol 15(3):382–386CrossRef

Shockley JM, Strauss HW, Chromik RR, Brodusch N, Gauvin R, Irissou E, Legoux JG (2013) In situ tribometry of cold-sprayed Al-Al₂O₃ composite coatings. Surf Coat Technol 215:350–356CrossRef

Shockley JM, Descartes S, Vo P, Irissou E, Chromik RR (2015) The influence of Al₂O₃ particle morphology on the coating formation and dry sliding wear behavior of cold sprayed Al-Al₂O₃ composites. Surf Coat Technol 270:324–333CrossRef

Silva FS, Bedoya J, Dosta S, Cinca N, Cano IG, Guilemany JM, Benedetti AV (2016) Corrosion characteristics of cold gas spray coatings of reinforced aluminum deposited onto carbon steel. Corros Sci 114:57–71CrossRef

Singh H, Bala N, Kaur N, Sharma SK, Kim DY, Prakash S (2015) Effect of additions of TiC and Re on high temperature corrosion performance of cold sprayed Ni-20Cr coatings. Surf Coat Technol 280:50–63CrossRef

Smid I, Segall AE, Walia P, Aggarwal G, Eden TJ, Potter JK (2012) Cold-sprayed Ni-hBN self-lubricating coatings. Tribol Trans 55(5):599–605CrossRef

Sova A, Kosarev VF, Papyrin A, Smurov I (2010) Effect of ceramic particle velocity on cold spray deposition of metal-ceramic coatings. J Therm Spray Technol 20(1-2):285–291CrossRef

Sova A, Maestracci R, Jeandin M, Bertrand P, Smurov I (2016) Kinetics of composite coating formation process in cold spray: modelling and experimental validation. Surf Coat Technol. https://doi.org/10.1016/j.surfcoat.2016.06.084

Spencer K, Zhang MX (2009) The use of kinetic metallization to form intermetallic reinforced composite coatings by post-spray heat treatment. Surf Coat Technol 203(20–21):3019–3025CrossRef

Spencer K, Fabijanic DM, Zhang MX (2009) The use of Al-Al2O3 cold spray coatings to improve the surface properties of magnesium alloys. Surf Coat Technol 204(3):336–344CrossRef

Suo XK, Suo QL, Li WY, Planche MP, Liao HL (2014) Effects of SiC volume fraction and particle size on the deposition behavior and mechanical properties of cold-sprayed AZ91D/SiC_p composite coatings. J Therm Spray Technol 23(1):91–97CrossRef

Tao Y, Xiong T, Sun C, Jin H, Du H, Li T (2009) Effect of α-Al₂O₃ on the properties of cold sprayed Al/α-Al₂O₃ composite coatings on AZ91D magnesium alloy. Appl Surf Sci 256(1):261–266CrossRef

Tazegul O, Meydanoglu O, Kayali ES (2013) Surface modification of electrical contacts by cold gas dynamic spraying process. Surf Coat Technol 236(24):159–165CrossRef

Tazegul O, Dylmishi V, Cimenoglu H (2016) Copper matrix composite coatings produced by cold spraying process for electrical applications. Arch Civ Mech Eng 16(3):344–350CrossRef

Tlotleng M, Akinlabi E, Shukla M, Pityana S (2015) Microstructural and mechanical evaluation of laser-assisted cold sprayed bio-ceramic coatings: potential use for biomedical applications. J Therm Spray Technol 24(3):423–435CrossRef

Triantou KI, Pantelis DI, Guipont V, Jeandin M (2015) Microstructure and tribological behavior of copper and composite copper+alumina cold sprayed coatings for various alumina contents. Wear 336-337:96–107CrossRef

Wang Q, Spencer K, Birbilis N, Zhang M-X (2010) The influence of ceramic particles on bond strength of cold spray composite coatings on AZ91 alloy substrate. Surf Coat Technol 205(1):50–56CrossRef

Wang HT, Li CJ, Ji GC, Yang GJ (2012) Annealing effect on the intermetallic compound formation of cold sprayed Fe/Al composite coating. J Therm Spray Technol 21(3–4):571–577CrossRef

Wang Q, Birbilis N, Huang H, Zhang M-X (2013) Microstructure characterization and nanomechanics of cold-sprayed pure Al and Al-Al2O3 composite coatings. Surf Coat Technol 232:216–223CrossRef

Wang Y, Normand B, Mary N, Yu M, Liao H (2014) Microstructure and corrosion behavior of cold sprayed SiCp/al 5056 composite coatings. Surf Coat Technol 251:264–275CrossRef

Wang J, Kong L, Li T, Xiong T (2016) A novel TiAl 3 /Al ₂ O ₃ composite coating on r-TiAl alloy and evaluating the oxidation performance. Appl Surf Sci 361:90–94CrossRef

Woo DJ, Sneed B, Peerally F, Heer FC, Brewer LN, Hooper JP, Osswald S (2013) Synthesis of nanodiamond-reinforced aluminum metal composite powders and coatings using high-energy ball milling and cold spray. Carbon 63:404–415CrossRef

Woo DJ, Heer FC, Brewer LN, Hooper JP, Osswald S (2015) Synthesis of nanodiamond-reinforced aluminum metal matrix composites using cold-spray deposition. Carbon 86:15–25CrossRef

Xia M, Huang P, Cu R-K, Ge C-C (2016) Cold sprayed W/Ni/Fe alloy coating: microstructure and mechanical properties. Surf Coat Technol 291:376–381CrossRef

Xiong Y, Zhang MX (2014) The effect of cold sprayed coatings on the mechanical properties of AZ91D magnesium alloys. Surf Coat Technol 253(9):89–95CrossRef

Xu Y, Hutchings IM (2006) Cold spray deposition of thermoplastic powder. Surf Coat Technol 201(6):3044–3050CrossRef

Yamada M, Wakabayashi J, Kitamura J, et al. (2009) Fabrication of Cu-MoS₂ composite coating by cold spraying and evaluation of its property [C]. International thermal spray conference

Yandouzi M, Richer P, Jodoin B (2009) SiC particulate reinforced Al-12Si alloy composite coatings produced by the pulsed gas dynamic spray process: microstructure and properties. Surf Coat Technol 203(20–21):3260–3270CrossRef

Yang GJ, Zhao SN, Li CX, Li CJ (2013) Effect of phase transformation mechanism on the microstructure of cold-sprayed Ni/Al-Al₂O₃ composite coatings during post-spray annealing treatment. J Therm Spray Technol 22(2):398–405CrossRef

Yin S, Xie Y, Cizek J, Ekoi E, Hussain T, Dowling D, Lupoi R (2017) Advanced diamond-reinforced metal matrix composites via cold spray: properties and deposition mechanism. Compos Part B-Eng. https://doi.org/10.1016/j.compositesb.2017.01.009

Yu M, Li WY, Suo XK, Liao HL (2013) Effects of gas temperature and ceramic particle content on microstructure and microhardness of cold sprayed SiC_p/Al 5056 composite coatings. Surf Coat Technol 220:102–106CrossRef

Yu M, Suo XK, Li WY, Wang YY, Liao HL (2014) Microstructure, mechanical property and wear performance of cold sprayed Al5056/SiCp composite coatings: effect of reinforcement content. Appl Surf Sci 289(0):188–196CrossRef

Zhang G, Li WY, Cherigui M, Zhang C, Liao H, Bordes JM, Coddet C (2007) Structures and tribological performances of PEEK (poly-ether-ether-ketone)-based coatings designed for tribological application. Prog Org Coat 60(1):39–44CrossRef

Zhang Y, Shockley JM, Vo P, Chromik RR (2016) Tribological behavior of a cold-sprayed Cu-MoS₂ composite coating during dry sliding wear. Tribol Lett 62(1):1–12CrossRef

Zhou X, Mohanty P (2012) Electrochemical behavior of cold sprayed hydroxyapatite/titanium composite in Hanks solution. Electrochim Acta 65:134–140CrossRef

Titel: Metal Matrix Composite Coatings by Cold Spray
verfasst von: Min Yu
Wenya Li
Verlag: Springer International Publishing
Buch: Cold-Spray Coatings
Print ISBN: 978-3-319-67182-6

Electronic ISBN: 978-3-319-67183-3

Copyright-Jahr: 2018
DOI: https://doi.org/10.1007/978-3-319-67183-3_10

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht