Ausgabe 10/2001
Inhalt (29 Artikel)
On the microstructural instability of an experimental nickel-based single-crystal superalloy
M. S. A. Karunaratne, C. M. F. Rae, R. C. Reed
Cooling precipitation and strengthening study in powder metallurgy superalloy U720LI
Jian Mao, Keh-Minn Chang, Wanhong Yang, Koushik Ray, Suhas P. Vaze, David U. Ferrer
Phase transformations in Ti-6Al-4V-xH alloys
J. I. Qazi, J. Rahim, F. H. (SAM) Fores, O. N. Senkov, A. Genc
Microstructural Modification and property improvement of boride/Ti-6Al-4V surface-alloyed materials fabricated by high-energy electron-beam irradiation
Kwangjun Euh, Jongmin Lee, Sunghak Lee
Influence of stepped austempering process on the fracture toughness of austempered ductile iron
Cheng-Hsun Hsu, Tao-Liang Chuang
Effects of carbon and chromium additions on the wear resistance and surface roughness of cast high-speed steel rolls
Yong Jung Kang, Jun Cheol Oh, Hui Choon Lee, Sunghak Lee
Microstructure and texture evolution under strain-path changes in low-carbon interstitial-free steel
E. V. Nesterova, B. Bacroix, C. Teodosiu
The effect of hold time and waveform on the high-temperature, low-cycle fatigue properties of a Nb-A286 alloy
Byung Sup Rho, Ki Jae Kim, Soo Woo Nam, Soo Woo Nam
Effect of fatigue damage on the dynamic fracture toughness of En-8-grade steel
P. Talukdar, S. K. Sen, A. K. Ghosh
Localized corrosion susceptibility of Al-Li-Cu-Mg-Zn alloy AF/C458 due to interrupted quenching from solutionizing temperature
J. E. Kertz, P. I. Gouma, R. G. Buchheit
Electron and laser beam welding of high strain rate superplastic Al-6061/SiC composites
R. Y. Huang, J. C. Huang, S. C. Chen
The postweld heat-treatment response of simulated coarse-grained heat-affected zones in a new ferritic steel
J. G. Nawrocki, J. N. DuPont, A. R. Marder, C. V. Robino
Approach to saturation in textured soft magnetic materials
A. D. Rollett, M. L. Storch, E. J. Hilinski, S. R. Goodman
Density and solidification shrinkage of hypoeutectic aluminum-silicon alloys
T. Magnusson, L. Arnberg
Wear-resistant amorphous and nanocomposite steel coatings
D. J. Branagan, W. D. Swank, D. C. Haggard, J. R. Fincke
Investigation of striation formation in thin stainless steel tube during pulsed Nd:YAG laser cutting process by numerical simulation
Byoung-Cheol Kim, To-Hoon Kim, Yangsoo Jang, Kwang-Hoe Chung
Effects of heating rate on densification and grain growth during field-assisted sintering of α-Al2O3 and MoSi2 powders
L. A. Stanciu, V. Y. Kodash, J. R. Groza
Microscopic characterization of a TiB2-Carbon material composite: Raw materials and composite characterization
Martin Dionne, Amir Mirchi, Gilles L’Espérance
Effects of macroscopic defects on the damping behavior of aluminum and Zn-27 Pct Al alloy
Zhonghua Ma, Fusheng Han, Jianning Wei, Junchang Gao
The effect of wetting kinetics on the penetration of a layered capillary
Rajiv Asthana
Formation of intermetallic compounds in SnPbAg, SnAg, and SnAgCu solders on Ni/Au metallization
K. Y. Lee, M. Li
Separation of scales for growth of an alloy needle crystal
R. F. Sekerka, S. R. Coriell, G. B. McFadden
Apparent grain growth behavior of submicrometer grained Al-3 Pct Mg during static annealing after fabrication by severe plastic straining
Kyung-Tae Park, Hyuk-Joo Kwon, Dong Hyuk Shin