nach oben

Journal of Materials Engineering and Performance

Erschienen in:

28.03.2023 | Technical Article

Microstructure Evolution and Mechanical Properties of Inconel 625 Foils

verfasst von: Fangjun Wang, Haiding Liu, Jia Li, Hong Wan, Lichuan Yu, Binbin Liu

Erschienen in: Journal of Materials Engineering and Performance | Ausgabe 14/2023

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The microstructure evolution and mechanical properties of cold-rolled Inconel 625 foil with thickness of 50 μm were investigated. After annealing at 650 and 700 °C, the cold-rolled microstructure transformed into smaller recrystallization grain and annealing twins, while the fraction and particle size of MC carbides increased with increasing aging temperature and duration. TEM analysis confirms the precipitation of irregular lens and near spherical-shaped \(\gamma^{\prime \prime }\) phase at 700 °C, which is not observed in the sample annealed at 650 °C. The foil after annealing at 650 °C for 48 h exhibits the best mechanical properties with ultimate tensile strength and yield strength of 1515 and 1077 MPa as well as reasonable elongation of 19.5%. But the much larger and coarser carbides result in obvious reduction in tensile properties for the sample after 48 h-aging at 700 °C.

Vorheriger Artikel Effects of Isothermal Solution Treatment on Microstructure Evolution and Tensile Properties of High Strength Near-Β Ti Alloy

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Nur mit Berechtigung zugänglich

T. Allen, J. Busby, M. Meyer, and D. Petti, Materials Challenges for Nuclear Systems, Mater. Today, 2010, 13, p 4–23.CrossRef

E. Salama, M.M. Eissa, and A.S. Tageldin, Distinct Properties of Tungsten Austenitic Stainless Alloy as A Potential Nuclear Engineering Material, Nucl. Eng., 2019, 51, p 784–791.CrossRef

G.D. Han, Z.P. Lu, X.K. Ru, J.J. Chen, Q. Xiao, and Y.W. Tian, Improving The Oxidation Resistance of 316L Stainless Steel In Simulated Pressurized Water Reactor Primary Water by Electropolishing Treatment, J. Nucl. Mater., 2015, 467, p 194–204.CrossRef

Q.B. He, F.S. Pan, D.Z. Wang, H.D. Liu, F. Guo, Z.W. Wang, and Y.L. Ma, Microstructure and Properties of 316L Stainless Steel Foils for Pressure Sensor of Pressurized Water Reactor, Nucl. Eng. Tech., 2021, 53, p 172–177.CrossRef

C.V. Yıldırım, T. Kıvakb, M. Sarıkayac, and Ş Şirin, Evaluation of Tool Wear, Surface Roughness/Topography and Chip Morphology When Machining of Ni-based Alloy 625 under MQL, Cryogenic Cooling and CryoMQL, J. Mater. Res. Technol., 2020, 9, p 2079–2092.CrossRef

Y.B. Gao, Y.T. Ding, J.J. Chen, J.Y. Xu, Y.J. Ma, and X.M. Wang, Effect of Twin Boundaries on The Microstructure and Mechanical Properties of Inconel 625 Alloy, Mater. Sci. Eng. A, 2019, 767, p 702–710.CrossRef

K.H. Lo, C.H. Shek, and J.K.L. Lai, Recent Developments in Stainless Steels, Mater. Sci. Eng. R, 2009, 65, p 39–104.CrossRef

A.K. Jena and M.C. Chaturvedi, The Role of Alloying Elements in The Design of Nickel- base Superalloys, J. Mater. Sci., 1984, 19, p 3121–3139.CrossRef

L.M. Suave, J. Cormier, P. Villechaise, A. Soula, Z. Hervier, D. Bertheau, and J. Laigo, Microstructural Evolutions During Thermal Aging of Alloy 625: Impact of Temperature and Forming Process, Metall. Mater. Trans. A, 2014, 45, p 2963–2982.CrossRef

10.

M.D. Mathew, P. Parameswaran, and K.B.S. Rao, Microstructural Changes in Alloy 625 During High Temperature Creep, Mater. Charact., 2008, 59, p 508–513.CrossRef

11.

F. Cortial, J.M. Corrieu, and C. Vernot-Loier, Influence of Heat Treatments on Microstructure, Mechanical Properties, and Corrosion Resistance of Weld Alloy 625, Metall. Mater. Trans. A, 1995, 26, p 1273–1286.CrossRef

12.

C. Thomas and P. Tait, The Performance of Alloy 625 in Long-term Intermediate Temperature Applications, Int. J. Press. Vessels Piping, 1994, 59, p 41–49.CrossRef

13.

J. Mittra, S. Banerjee, R. Tewari, and G.K. Dey, Fracture Behavior of Alloy 625 with Different Precipitate Microstructures, Mater. Sci. Eng. A, 2013, 574, p 86–93.CrossRef

14.

S. Floreen, G.E. Fuch, W.J. Yang, and E.A. Loria, ed., Superalloys 718, 625, 706 and various derivatives, TMS, Warrendale, 1994, PA, p 13–37

15.

N.D. Evans, P.J. Maziasz, J.P. Shingledecker, and Y. Yamamoto, Microstructure Evolution of Alloy 625 Foil and Sheet During Creep at 750 °C, Mater. Sci. Eng. A, 2008, 498, p 412–420.CrossRef

16.

P. Kontis, A. Kostkaa, D. Raabe, and B. Gault, Influence of Composition and Precipitation Evolution on Damage at Grain Boundaries in A Crept Polycrystalline Ni- based Superalloy, Acta Mater., 2019, 166, p 158–167.CrossRef

17.

X.D. Liu, J.K. Fan, P.Z. Zhang, J. Xie, F.L. Chen, D.G. Liu, R.H. Yuan, B. Tang, H.C. Kou, and J.S. Li, Temperature Dependence of Deformation Behavior, Microstructure Evolution and Fracture Mechanism of Inconel 625 Superalloy, J. Alloys Compd., 2021, 869, p 159342.CrossRef

18.

D.F. Li, Q.M. Guo, S.L. Guo, H.J. Peng, and Z.G. Wu, The Microstructure Evolution and Nucleation Mechanisms of Dynamic Recrystallization in Hot-deformed Inconel 625 Superalloy, Mater. Des., 2011, 32, p 696–705.CrossRef

19.

M.D. Mathew, K.B.S. Rao, and S.L. Mannan, Creep Properties of Service-Exposed Alloy 625 after Resolution Annealing Treatment, Mater. Sci. Eng. A, 2004, 372, p 327–333.CrossRef

20.

S.K. Rai, A. Kumar, V. Shankar, T. Jayakumar, K.B.S. Rao, and B. Raj, Characterization of Microstructures in Inconel 625 Using X-ray Diffraction Peak Broadening and Lattice Parameter Measurements, Scr. Mater., 2004, 51, p 59–63.CrossRef

21.

M. Sundararaman, L. Kumar, G.E. Prasad, P. Mukhopadhyay, and S. Banerjee, Precipitation of an Intermetallic Phase with Pt2Mo-type Structure in Alloy 625, Metall. Mater. Trans. A, 1999, 30, p 41–52.CrossRef

22.

J. Huebner, D. Kata, J. Kusiński, P. Rutkowski, and J. Lis, Microstructure of Laser Cladded Carbide Reinforced Inconel 625 Alloy for Turbine Blade Application, Ceram. Int., 2017, 43, p 8677–8684.CrossRef

23.

Ö. Özgün, H.Ö. Gülsoy, R. Yilmaz, and F. Findik, Injection Molding of Nickel based 625 Superalloy: Sintering, Heat treatment, Microstructure and Mechanical Properties, J. Alloys Compd., 2013, 546, p 192–207.CrossRef

24.

L.M. Suave: M.Sc. Dissertation, ISAE-ENSMA, 2012

25.

M. Sundararaman, R. Kishore, and P. Mukhopadhyay, Superalloys 718, 625, 706 and Various Derivatives, E.A. Loria, ed., TMS, Pittsburgh, PA, p 405–417 (1994)

26.

J. Mittra, J.S. Dubey, U.D. Kulkarni, and G.K. Dey, Role of Dislocation Density in Raising the Stage II Work-Hardening Rate of Alloy 625, Mater. Sci. Eng. A, 2009, 512, p 87–91.CrossRef

27.

J. Mittra, J.S. Dubey, and S. Banerjee, Acoustic Emission Technique Used for Detecting Early Stages of Precipitation during Aging of Inconel 625, Scr. Mater., 2003, 49, p 1209–1214.CrossRef

28.

R. Rodriguez, R.W. Hayes, P.B. Berbon, and E.J. Lavernia, Tensile and Creep Behavior of Cryomilled Inco 625, Acta Mater., 2003, 51, p 911–929.CrossRef

29.

P. Kontis, D.M. Collins, S. Johansson, A.J. Wilkinson, J.J. Moverare, and R.C. Reed, Crack initiation and propagation during thermal-mechanical fatigue of IN792: effects of dwell time. in 13th International Symposium on Superalloys, SUPERALLOYS 2016, (pp. 763-772). (2016)

Titel: Microstructure Evolution and Mechanical Properties of Inconel 625 Foils
verfasst von: Fangjun Wang
Haiding Liu
Jia Li
Hong Wan
Lichuan Yu
Binbin Liu
Publikationsdatum: 28.03.2023
Verlag: Springer US
Erschienen in: Journal of Materials Engineering and Performance / Ausgabe 14/2023
Print ISSN: 1059-9495
Elektronische ISSN: 1544-1024
DOI: https://doi.org/10.1007/s11665-023-08114-x

Investigation on 3D Printing of Graphene and Multi-walled Carbon Nanotube Mixed Flexible Electrically Conductive Parts Using Fused Filament Fabrication

Technical Article

Effect of Gamma Radiation on the Electrochemical Behavior of AISI 8620 Steel Coated with Diamond-Like Carbon

Technical Article

Triethoxyoctylsilane-Modified SiO2 Nanoparticle-Based Superhydrophobic Coating for Corrosion Resistance of Mild Steel

Technical Article

Mechanical and Tribological Behavior of Branched Polyethyleneimine/Polyacrylic Acid Coatings on Ti6Al4V Substrate

Technical Article

Influence of Nanometric and Micrometric Reinforcement on Machining of Powder-Forged Al-7075/Y2O3 Composites

Technical Article

Effects of Rolling-Cryogenic Process on Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets

Technical Article

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht