nach oben

Rock Mechanics and Rock Engineering

Erschienen in:

21.03.2017 | Original Paper

Rock Fracture Toughness Study Under Mixed Mode I/III Loading

verfasst von: M. R. M. Aliha, A. Bahmani

Erschienen in: Rock Mechanics and Rock Engineering | Ausgabe 7/2017

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

Fracture growth in underground rock structures occurs under complex stress states, which typically include the in- and out-of-plane sliding deformation of jointed rock masses before catastrophic failure. However, the lack of a comprehensive theoretical and experimental fracture toughness study for rocks under contributions of out-of plane deformations (i.e. mode III) is one of the shortcomings of this field. Therefore, in this research the mixed mode I/III fracture toughness of a typical rock material is investigated experimentally by means of a novel cracked disc specimen subjected to bend loading. It was shown that the specimen can provide full combinations of modes I and III and consequently a complete set of mixed mode I/III fracture toughness data were determined for the tested marble rock. By moving from pure mode I towards pure mode III, fracture load was increased; however, the corresponding fracture toughness value became smaller. The obtained experimental fracture toughness results were finally predicted using theoretical and empirical fracture models.

Vorheriger Artikel Laboratory Investigation of Coal Deformation Behavior and Its Influence on Permeability Evolution During Methane Displacement by CO2

Nächster Artikel Mechanical Properties of Gas Shale During Drilling Operations

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Abd-Elhady A (2013) Mixed mode I/II stress intensity factors through the thickness of disc type specimens. Eng Solid Mech 1:119–128CrossRef

Ahmadi-Moghadam B, Taheri F (2013) An effective means for evaluating mixed-mode I/III stress intensity factors using single-edge notch beam specimen. J Strain Anal Eng Des 48(4):245–257CrossRef

Aliha MRM, Ayatollahi MR (2011) Mixed mode I/II brittle fracture evaluation of marble using SCB specimen. Proc Eng 10:311–318CrossRef

Aliha MRM, Ayatollahi MR (2013) Two-parameter fracture analysis of SCB rock specimen under mixed mode loading. Eng Fract Mech 103:115–123CrossRef

Aliha MRM, Ayatollahi MR (2014) Rock fracture toughness study using cracked chevron notched Brazilian disc specimen under pure modes I and II loading—a statistical approach. Theor Appl Fract Mech 69:17–25CrossRef

Aliha MRM, Rezaei M (2011) Experimental and theoretical study of fracture paths in brittle cracked materials subjected to pure mode II loading. Applied mechanics and materials, vol 70. Trans Tech Publications, Zurich, pp 159–164

Aliha MRM, Ayatollahi MR, Ashtari R (2006) Mode I and mode II fracture toughness testing for a coarse grain marble. Appl Mech Mater 5:181–188CrossRef

Aliha MRM, Ayatollahi MR, Smith DJ, Pavier MJ (2010) Geometry and size effects on fracture trajectory in a limestone rock under mixed mode loading. Eng Fract Mech 77:2200–2212CrossRef

Aliha MRM, Ayatollahi MR, Akbardoost J (2012a) Typical upper bound–lower bound mixed mode fracture resistance envelopes for rock material. Rock Mech Rock Eng 45(1):65–74CrossRef

Aliha MRM, Sistaninia M, Smith DJ, Pavier MJ, Ayatollahi MR (2012b) Geometry effects and statistical analysis of mode I fracture in guiting limestone. Int J Rock Mech Min Sci 51:128–135CrossRef

Aliha MRM, Hosseinpour GR, Ayatollahi MR (2013) Application of cracked triangular specimen subjected to three-point bending for investigating fracture behavior of rock materials. Rock Mech Rock Eng 46(5):1023–1034CrossRef

Aliha MRM, Bahmani A, Akhondi S (2015a) Numerical analysis of a new mixed mode I/III fracture test specimen. Eng Fract Mech 134:95–110CrossRef

Aliha MRM, Bahmani A, Akhondi S (2015b) Determination of mode III fracture toughness for different materials using a new designed test configuration. Mater Des 86:863–871CrossRef

Aliha MRM, Bahmani A, Akhondi S (2016a) Mixed mode fracture toughness testing of PMMA with different three-point bend type specimens. Eur J Mech A/Solids 58:148–162CrossRef

Aliha MRM, Berto F, Bahmani A, Akhondi S, Barnoush A (2016b) Fracture assessment of polymethyl methacrylate using sharp notched disc bend specimens under mixed mode I + III loading. Phys Mesomech 19(4):355–364CrossRef

Aliha MRM, Bahmani A, Akhondi S (2016c) A novel test specimen for investigating the mixed mode I + III fracture toughness of hot mix asphalt composites—experimental and theoretical study. Int J Solids Struct 90:167–177CrossRef

Aliha MRM, Mahdavi E, Ayatollahi MR (2017) The influence of specimen type on tensile fracture toughness of rock materials. Pure Appl Geophys 174(3):1237–1253CrossRef

Arcan M, Hashin Z, Volosnin A (1978) A method to produce uniform plane-stress states with application to fibre-reinforced materials. Exp Mech 18:141–146CrossRef

Atkinson C, Smelser RE, Sanchez J (1982) Combined mode fracture via the cracked Brazilian disc test. Int J Fract 18:279–291

Avci A, Akdemir A, Arikan H (2005) Mixed-mode fracture behavior of glass fiber reinforced polymer concrete. Cem Concr Res 35(2):243–247CrossRef

Awaji H, Kato T (1999) Criterion for combined mode I–II of brittle fracture. Mater Trans, JIM 40(9):972–979CrossRef

Awaji H, Sato S (1978) Combined mode fracture toughness measurement by the disc test. J Eng Mater Tech 100:175–182CrossRef

Ayatollahi MR, Aliha MRM (2008) On the use of Brazilian disc specimen for calculating mixed mode I–II fracture toughness of rock materials. Eng Fract Mech 75:4631–4641CrossRef

Ayatollahi MR, Aliha MRM (2009) Analysis of a new specimen for mixed mode fracture tests on brittle materials. Eng Fract Mech 76:1563–1573CrossRef

Ayatollahi MR, Saboori B (2014) Maximum tangential strain energy density criterion for general mixed mode I/II/III brittle fracture. Int J Damage Mech 24(2):263–278CrossRef

Backers T, Stephansson O (2012) ISRM suggested method for the determination of mode II fracture toughness. In: The ISRM suggested methods for rock characterization, testing and monitoring: 2007–2014, Part 1. Springer, pp 45–56. doi:10.1007/978-3-319-07713-0_4

Bahmani A, Aliha MRM, Berto F (2017) Investigation of fracture toughness for a polycrystalline graphite under combined tensile-tear deformation. Theor Appl Fract Mech. doi:10.1016/j.tafmec.2017.02.011

Banks-Sills L, Bortman Y (1986) A mixed mode fracture specimen; analysis and testing. Int J Fract 30:181–201CrossRef

Bažant ZP, Prat PC (1988) Measurement of mode III fracture energy of concrete. Nucl Eng Des 106(1):1–8CrossRef

Berto F, Lazzarin P (2009) A review of the volume-based strain energy density approach applied to V-notches and welded structures. Theor Appl Fract Mech 52(3):183–194CrossRef

Bieniawski ZT, Bernede MJ (1979) Suggested methods for determining the uniaxial compressive strength and deformability of rock materials: part 1. Suggested method for determining deformability of rock materials in uniaxial compression. Int J Rock Mech Min Sci Geo Abstr 16(2):138–140CrossRef

Buchholz FG, Pirro PJM, Richard HA, Dreyer KH (1987) Numerical and experimental mixed-mode analysis of a compact tension shear specimen. In: Proceedings of the fourth international conference on numerical methods in fracture mechanics, Pineridge Press, Swansea, pp 641–656

Chang SH, Lee CI, Jeon S (2002) Measurement of rock fracture toughness under modes I and II and mixed-mode conditions by using disc-type specimen. Eng Geol 66:79–97CrossRef

Choi SR, Zhu D, Miller RA (2005) Fracture behavior under mixed mode loading of ceramic plasma-sprayed thermal barrier coatings at ambient and elevated temperatures. Eng Fract Mech 72(13):2144–2158CrossRef

Cotterell B, Rice J (1980) Slightly curved or kinked cracks. Int J Fract 16(2):155–169CrossRef

Dehghan AN, Goshtasbi K, Ahangari K, Jin Y, Bahmani A (2017) 3D numerical modeling of the propagation of hydraulic fracture at its intersection with natural (pre-existing) fracture. Rock Mech Rock Eng 50:367–386CrossRef

Eftekhari M, Baghbanan A, Bagherpour R (2014) The effect of fracture patterns on penetration rate of TBM in fractured rock mass using probabilistic numerical approach. Arab J Geosci 7(12):5321–5331CrossRef

Fett T, Gerteisen G, Hahnenberger S, Martin G, Munz D (1995) Fracture tests for ceramics under mode-I, mode-II and mixed mode loading. J Eur Ceram Soc 15:307–312CrossRef

Franklin JA (1985) Suggested method for determining point load strength. Int J Rock Mech Min Sci Geo Abstr 22(2):51–60CrossRef

Hasanpour R, Choupani N (2009) Rock fracture characterization using the modified Arcan test specimen. Int J Rock Mech Min Sci 46(2):346–354CrossRef

Hirano K (2005) Application of eutectic composites to gas turbine system and fundamental fracture properties up to 1700 °C. J Eur Ceram Soc 25(8):1191–1199CrossRef

Kamat SV, Hirth JP (1996) Effect of aging on mixed-mode I/III fracture toughness of 2034 aluminum alloys. Acta Mater 44(3):1047–1054CrossRef

Kamat SV, Hirth JP, Mehrabian R (1989) Combined mode I—mode III fracture toughness of alumina particulate-reinforced aluminum alloy–matrix composites. Scr Metall 23(4):523–528CrossRef

Khan K, Al-Shayea NA (2000) Effect of specimen geometry and testing method on mixed mode I–II fracture toughness of a limestone rock from Saudi Arabia. Rock Mech Rock Eng 33:179–206CrossRef

Kui Z (2003) Mixed mode I–II–III fracture criterion and its application to cement mortar. Doctoral dissertation

Kuruppu MD, Obara Y, Ayatollahi MR, Chong KP, Funatsu T (2013) The ISRM suggested methods for rock characterization, testing and monitoring: 2007–2014. In: ISRM-suggested method for determining the mode I static fracture toughness using semi-circular bend specimen. Springer, pp 107–114. doi:10.1007/978-3-319-07713-0_8

Lazzarin P, Berto F (2005) Some expressions for the strain energy in a finite volume surrounding the root of blunt V-notches. Int J Fract 135:161–185CrossRef

Lazzarin P, Berto F, Elices M, Gómez J (2009) Brittle failures from U- and V-notches in mode I and mixed, I + II, mode: a synthesis based on the strain energy density averaged on finite-size volumes. Fatigue Fract Eng Mater Struct 32(8):671–684CrossRef

Li LY, Xu ZQ, Li MX (2013) A experimental study of I–II–III mixed mode crack fracture of rock under different temperature. In: ICF13

Lim IL, Johnston IW, Choi SK, Boland JN (1994) Fracture testing of a soft rock with semi-circular specimens under three-point bending, part 2—mixed mode. Int J Rock Mech Min Sci Geomech Abstr 31(3):199–212CrossRef

Liu S, Chao YJ, Zhu X (2004) Tensile-shear transition in mixed mode I/III fracture. Int J Solids Struct 41(22):6147–6172CrossRef

Liu JS, Cao P, Liu J, Jiang Z (2015) Influence of confining stress on fracture characteristics and cutting efficiency of TBM cutters conducted on soft and hard rock. J Central South Univ 22:1947–1955CrossRef

Maccagno TM, Knott JF (1989) The fracture behavior of PMMA in mixed modes I and II. Eng Fract Mech 34(1):65–86CrossRef

Mahajan RV, Ravi-Chandar K (1989) An experimental investigation of mixed-mode fracture. Int J Fract 41:235–252CrossRef

Manoharan M, Hirth JP, Rosenfield AR (1991) Combined mode I–mode III fracture toughness of a spherodized 1090 steel. Acta Metall Mater 39(6):1203–1210CrossRef

Rao QH, Liao ZF (2005) Rock fracture under anti-plane shear (mode III) loading. J Central South Univ Technol 12(1):125–128CrossRef

Rao BC, Srinivas M, Kamat SV (2008) The effect of mixed mode I/III loading on the fracture toughness of Timetal 834 titanium alloy. Mater Sci Eng, A 476(1):162–168

Richard HA, Benitz K (1983) A loading device for the creation of mixed mode in fracture mechanics. Int J Fract 22:55–58CrossRef

Richard HA, Schramm B, Schirmeisen NH (2014) Cracks on mixed mode loading—theories, experiments, simulations. Int J Fatigue 62:93–103CrossRef

Seifi R, Omidvar N (2013) Fatigue crack growth under mixed mode I + III loading. Mar Struct 34:1–15CrossRef

Shetty DK, Rosenfield AR, Duckworth WH (1987) Mixed-mode fracture in biaxial stress state: application of the diametral compression (Brazilian disk) test. Eng Fract Mech 26(6):825–840CrossRef

Suresh S, Shih CF, Morrone A, O-Dowd NP (1990) Mixed-mode fracture toughness of ceramic materials. J Am Ceram Soc 73(5):1257–1267CrossRef

Tikare V, Choi SR (1993) Combined mode I and mode II fracture of monolithic ceramics. J Am Ceram Soc 76(9):2265–2272CrossRef

Tutluoglu L, Keles C (2011) Mode I fracture toughness determination with straight notched disk bending method. Int J Rock Mech Min Sci 48(8):1248–1261CrossRef

Ulusay R (ed) (2015) The ISRM suggested methods for rock characterization, testing and monitoring: 2007–2014. Springer, Switzerland

Xeidakis GS, Samaras IS, Zacharopoulos DA, Papakalitakis GE (1996) Crack growth in a mixed-mode loading on marble beams under three point bending. Int J Fract 79:197–208CrossRef

Zipf RK, Bieniawski ZT (1986) Mixed mode testing for fracture testing of coal based on critical energy density. In: Proceedings of 27th US symposium on rock mechanics, pp 16–23

Titel: Rock Fracture Toughness Study Under Mixed Mode I/III Loading
verfasst von: M. R. M. Aliha
A. Bahmani
Publikationsdatum: 21.03.2017
Verlag: Springer Vienna
Erschienen in: Rock Mechanics and Rock Engineering / Ausgabe 7/2017
Print ISSN: 0723-2632
Elektronische ISSN: 1434-453X
DOI: https://doi.org/10.1007/s00603-017-1201-7

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 7/2017

Modelling the Shear Behaviour of Clean Rock Discontinuities Using Artificial Neural Networks

Application of Q slope to Assess the Stability of Rock Slopes in Madrid Province, Spain

Experimental Study of Mode-I Fracture Toughness for Layered Shale Based on Two ISRM-Suggested Methods

Failure Mechanisms and Evolution Assessment of the Excavation Damaged Zones in a Large-Scale and Deeply Buried Underground Powerhouse

Role of Brittle Behaviour of Soft Calcarenites Under Low Confinement: Laboratory Observations and Numerical Investigation

Investigation of the Effect of Cemented Fractures on Fracturing Network Propagation in Model Block with Discrete Orthogonal Fractures