Sub-micron Co–Al2O3 composite powders were synthesized by ultrasonic-assisted electroless plating process at room temperature with a one-step activating method pretreatment. The effect of process parameters on plating rate, Co content, and the uniformity of cobalt layer was analyzed by transmission electron microscopy (TEM). The results show that as the initial pH values of plating bath increase, the plating rate increases. The plating rate declines as the load increases when the load of powders is less than 12 g·L−1, but increases when the load is greater than 12 g·L−1. The relative Co content of the Co–Al2O3 powder declines with the powder load increasing.
Bitte loggen Sie sich ein, um Zugang zu diesem Inhalt zu erhalten
Han JC, Wang BL. Thermal shock resistance of ceramics with temperature-dependent material properties at elevated temperature. Acta Mater. 2011;59(4):1373.
CrossRef
[2]
Liu CX, Zhang JH, Sun JL, Zhang XH. Tribological properties of pressureless sintered alumina matrix ceramic materials improved by diopside. J Eur Ceram Soc. 2008;28(1):199.
CrossRef
[3]
Zhao J, Yuan XL, Zhou YH. Processing and characterization of an Al
2O
3/WC/TiC micro-nano-composite ceramic tool material. Mater Sci Eng, A. 2010;527(7–8):1844.
CrossRef
[4]
Fritsch M, Klemm H, Herrmann M, Schenk B. Corrosion of selected ceramic materials in hot gas environment. J Eur Ceram Soc. 2006;26(16):3557.
CrossRef
[5]
Li J, Sun JL, Huang LP. Effects of ductile cobalt on fracture behavior of Al
2O
3–TiC ceramic. Mater Sci Eng, A. 2002;323(1–2):17.
CrossRef
[6]
Azadmehr A, Taheri-Nassaj E. An in situ (W, Ti)C–Ni composite fabricated by SHS method. J Non-Cryst Solids. 2008;354(27):3225.
CrossRef
[7]
Vallauri D, DeBenedetti B, Jaworska L, Klimczyk P, Rodriguez MA. Wear-resistant ceramic and metal-ceramic ultrafine composites fabricated from combustion synthesised metastable powders. Int J Refract Met Hard Mater. 2009;27(6):996.
CrossRef
[8]
Chen ZC, Takeda T, Ikeda K, Murakami T. The influence of powder particle size on microstructural evolution of metal-ceramic composites. Scripta Mater. 2000;43(12):1103.
CrossRef
[9]
Yin ZJ, Tao SY, Zhou XM, Ding CX. Microstructure and mechanical properties of Al
2O
3–Al composite coatings deposited by plasma spraying. Appl Surf Sci. 2008;254(6):1636.
CrossRef
[10]
Babakhani A, Zahabi E, Mehrabani HY. Fabrication of Fe/Al
2O
3 composite foam via combination of combustion synthesis and spark plasma sintering techniques. J Alloys Compd. 2012;514(2):20.
CrossRef
[11]
Luo LM, Wu YC, Li J, Zheng YC. Preparation of nickel-coated tungsten carbide powders by room temperature ultrasonic-assisted electroless plating. Surf Coat Technol. 2011;206(6):1091.
CrossRef
[12]
Dai JH, Liu XZ, Zhai HZ, Liu ZF, Tian JT. Preparation of Ni-coated Si
3N
4 powders via electroless plating method. Ceram Int. 2009;35(8):3407.
CrossRef
[13]
Zhu SL, Tang L, Cui ZD, Wei Q, Yang XJ. Preparation of copper-coated β-SiC nanoparticles by electroless plating. Surf Coat Technol. 2011;205(8–9):2985.
CrossRef
[14]
Ma Z, Wang JB, Liu QF, Yuan J. Microwave absorption of electroless Ni–Co–P-coated SiO
2 powder. Appl Surf Sci. 2009;255(13–14):6629.
CrossRef
[15]
Yuan YF, Tu JP, Guo SY, Wu JB, Ma M, Yang JL, Wang XL. Characteristics and electrochemical performance of Ni-coated ZnO prepared by an electroless plating process. Appl Surf Sci. 2008;254(16):5080.
CrossRef
[16]
Li J, Huang JW, Zhou Y, Tao X. Synthesis of modified Li
4Ti
5O
12 anode material with electroless plating nickel and its electrochemical properties. Chin J Rare Met. 2014;38(2):224.
[17]
Chen WW, Gao W, He YD. A novel electroless plating of Ni–P–TiO
2 nano-composite coatings. Surf Coat Technol. 2010;204(15):2493.
CrossRef
[18]
Wang H, Jia JF, Song HZ, Hu X, Sun HW, Yang DL. The preparation of Cu-coated Al
2O
3 composite powders by electroless plating. Ceram Int. 2011;37(7):2181.
CrossRef
[19]
Jiang JT, Zhen L, Xu CY, Wu XL. Microstructure and magnetic properties of SiC/Co composite particles prepared by electroless plating. Surf Coat Technol. 2006;201(6):3139.
CrossRef
[20]
Zhang C, Ling GP, He JH. Co–Al
2O
3 nanocomposites powder prepared by electroless plating. Mater Lett. 2003;58(1–2):200.
Über diesen Artikel
Titel
Sub-micron Co–Al2O3 composite powders prepared by room-temperature ultrasonic-assisted electroless plating
Die B2B-Firmensuche für Industrie und Wirtschaft: Kostenfrei in Firmenprofilen nach Lieferanten, Herstellern, Dienstleistern und Händlern recherchieren.
Lesen Sie in diesem ausgewählten Buchkapitel alles über den 3D-Druck im Hinblick auf Begriffe, Funktionsweise, Anwendungsbereiche sowie Nutzen und Grenzen additiver Fertigungsverfahren. Eigenschaften eines schlanken Produktionssystems sowie der Aspekt der „Schlankheit“ werden ebenso beleuchtet wie die Prinzipien und Methoden der Lean Production. Jetzt gratis downloaden!
Marktübersichten
Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.