nach oben

Journal of Nondestructive Evaluation

Erschienen in:

01.03.2021

X-ray Computed Microtomography Characterization of Ti6Al4V/CoCrMo Biomedical Composite Fabricated by Semi-solid Sintering

verfasst von: E. Mihalcea, H. J. Vergara-Hernández, L. Olmos, O. Jimenez, D. Arteaga, J. M. Salgado-López

Erschienen in: Journal of Nondestructive Evaluation | Ausgabe 1/2021

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

The semi-solid sintering of a novel Ti6Al4V/CoCrMo biomedical composite was investigated for the first time by semi-in situ X-ray computed microtomography. Composite was fabricated by dry mixing 15 vol% CoCrMo reinforcing particles with Ti6Al4V particles as matrix. The mixture was poured into a 1 mm diameter quartz capillary. 3D images of the same sample were acquired before and after sintering at different temperatures between 1050 and 1130 °C. Qualitative and quantitative analysis of the 3D images was carried out to observe the evolution of the microstructure. Formation and evolution with temperature of eutectic phase were monitored. It was found that the eutectic reaction started between Ti6Al4V and CoCrMo particles at 1050 °C, first in the contact area and then the liquid of eutectic phase was distributed over the surface of Ti6Al4V particles and filled the interparticle pores. Size and sphericity of Ti6Al4V and CoCrMo particles diminished as the volume fraction of eutectic phase increased. After sintering at 1130 °C most of CoCrMo particles disappeared because they react with Ti6Al4V to form the Ti₂Co phase. Porosity is reduced 15% mainly by reducing the smaller pores that can be filled by the eutectic phase. Thus, it was concluded that semi-in situ X-ray computed microtomography is an effective tool to investigate the semi-solid state sintering and to analyze the microstructure evolution and densification mechanisms.

Vorheriger Artikel Speckle Interferometric Investigation of Argon Pressure-Induced Surface Roughness Modifications in RF-Sputtered MoO3 Film

Nächster Artikel Noise Reduction for Improvement of Ultrasonic Monitoring Using Coda Wave Interferometry on a Real Bridge

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Bender, S., Chalivendra, V., Rahbar, N., El Wakil, S.: Mechanical characterization and modeling of graded porous stainless steel specimens for possible bone implant applications. Int. J. Eng. Sci. 53, 67–73 (2012). https://doi.org/10.1016/j.ijengsci.2012.01.004CrossRef

Dourandish, M., Godlinski, D., Simchi, A., Firouzdor, V.: Sintering of biocompatible P/M Co–Cr–Mo alloy (F-75) for fabrication of porosity-graded composite structures. Mater. Sci. Eng. A 472(1–2), 338–346 (2008). https://doi.org/10.1016/j.msea.2007.03.043CrossRef

Niinomi, M., Boehlert, C.J.: Titanium alloys for biomedical applications. In: Advances in Metallic Biomaterials, pp. 179–213. Springer, Berlin (2015)CrossRef

Mutlu, I.: Synthesis and characterization of Ti–Co alloy foam for biomedical applications. Trans. Nonferrous Met. Soc. China 26(1), 126–137 (2016). https://doi.org/10.1016/S1003-6326(15)64028-6CrossRef

Wang, R., Welsch, G.: Evaluation of an experimental Ti-Co alloy for dental restorations. J. Biomed. Mater. Res. B 101(8), 1419–1427 (2013). https://doi.org/10.1002/jbm.b.32961CrossRef

Murray, J.L.: The Co−Ti (cobalt−titanium) system. J. Phase Equil. 3(1), 74–86 (1982)CrossRef

Yang, C., Kang, L.M., Li, X.X., Zhang, W.W., Zhang, D.T., Fu, Z.Q., Li, Y.Y., Zhang, L.C., Lavernia, E.J.: Bimodal titanium alloys with ultrafine lamellar eutectic structure fabricated by semi-solid sintering. Acta Mater. 132, 491–502 (2017). https://doi.org/10.1016/j.actamat.2017.04.062CrossRef

Kang, L.M., Yang, C., Wang, F., Li, X.X., Zhu, D.Z., Zhang, W.W., Chen, W.P., Huan, Y.: Designing ultrafine lamellar eutectic structure in bimodal titanium alloys by semi-solid sintering. J. Alloys Compd. 702, 51–59 (2017). https://doi.org/10.1016/j.jallcom.2017.01.257CrossRef

Baruchel, J., Bleuet, P., Bravin, A., Coan, P., Lima, E., Madsen, A., Ludwig, W., Pernot, P., Susini, J.: Advances in synchrotron hard X-ray based imaging. C. R. Phys. 9(5–6), 624–641 (2008). https://doi.org/10.1016/j.crhy.2007.08.003CrossRef

10.

Olmos, L., Takahashi, T., Bouvard, D., Martin, C.L., Salvo, L., Bellet, D., Di Michiel, M.: Analysing the sintering of heterogeneous powder structures by in situ microtomography. Philos. Mag. 89(32), 2949–2965 (2009). https://doi.org/10.1080/14786430903150225CrossRef

11.

Bernard, D., Guillon, O., Combaret, N., Plougonven, E.: Constrained sintering of glass films: microstructure evolution assessed through synchrotron computed microtomography. Acta Mater. 59(16), 6228–6238 (2011). https://doi.org/10.1016/j.actamat.2011.06.022CrossRef

12.

Olmos, L., Bouvard, D., Salvo, L., Bellet, D., Di Michiel, M.: Characterization of the swelling during sintering of uniaxially pressed copper powders by in situ X-ray microtomography. J. Mater. Sci. 49(12), 4225–4235 (2014). https://doi.org/10.1007/s10853-014-8117-3CrossRef

13.

Vagnon, A., Rivière, J.P., Missiaen, J.M., Bellet, D., Di Michiel, M., Josserond, C., Bouvard, D.: 3D statistical analysis of a copper powder sintering observed in situ by synchrotron microtomography. Acta Mater. 56(5), 1084–1093 (2008). https://doi.org/10.1016/j.actamat.2007.11.008CrossRef

14.

Shuai, S., Guo, E., Phillion, A.B., Callaghan, M.D., Jing, T., Lee, P.D.: Fast synchrotron X-ray tomographic quantification of dendrite evolution during the solidification of MgSn alloys. Acta Mater. 118, 260–269 (2016). https://doi.org/10.1016/j.actamat.2016.07.047CrossRef

15.

Nogita, K., Yasuda, H., Prasad, A., McDonald, S.D., Nagira, T., Nakatsuka, N., Uesugi, K., St John, D.H.: Real time synchrotron X-ray observations of solidification in hypoeutectic Al–Si alloys. Mater. Charact. 85, 134–140 (2013). https://doi.org/10.1016/j.matchar.2013.08.015CrossRef

16.

Limodin, N., Salvo, L., Suéry, M., DiMichiel, M.: In situ investigation by X-ray tomography of the overall and local microstructural changes occurring during partial remelting of an Al–15.8 wt% Cu alloy. Acta Mater. 55(9), 3177–3191 (2007). https://doi.org/10.1016/j.actamat.2007.01.027CrossRef

17.

Terzi, S., Salvo, L., Suery, M., Dahle, A., Boller, E.: In situ microtomography investigation of microstructural evolution in Al–Cu alloys during holding in semi-solid state. Trans. Nonferr. Metal. Soc. China 20, s734–s738 (2010). https://doi.org/10.1016/S1003-6326(10)60572-9CrossRef

18.

Cabezas-Villa, J.L., Olmos, L., Bouvard, D., Lemus-Ruiz, J., Jiménez, O.: Processing and properties of highly porous Ti6Al4V mimicking human bones. J. Mater. Res. 33(6), 650–661 (2018). https://doi.org/10.1557/jmr.2018.35CrossRef

19.

Zhou, H., Zhou, M., Cheng, M., Guo, W., Cen, K.: Experimental study and X-ray microtomography based CFD simulation for the characterization of pressure drop in sinter bed. Appl. Therm. Eng. 112, 811–819 (2017). https://doi.org/10.1016/j.applthermaleng.2016.10.123CrossRef

20.

Renghini, C., Giuliani, A., Mazzoni, S., Brun, F., Larsson, E., Baino, F., Vitale-Brovarone, C.: Microstructural characterization and in vitro bioactivity of porous glass-ceramic scaffolds for bone regeneration by synchrotron radiation X-ray microtomography. J. Eur. Ceram. Soc. 33(9), 1553–1565 (2013). https://doi.org/10.1016/j.jeurceramsoc.2012.10.016CrossRef

21.

Klein, S., Weber, S., Theisen, W.: Investigation of heat transfer in a copper-infiltrated tool steel based on measurement, microtomography, and numerical simulation. Mater. Des. 156, 42–51 (2018). https://doi.org/10.1016/j.matdes.2018.06.028CrossRef

22.

Kaya, A.C., Zaslansky, P., Ipekoglu, M., Fleck, C.: Strain hardening reduces energy absorption efficiency of austenitic stainless steel foams while porosity does not. Mater. Des. 143, 297–308 (2018). https://doi.org/10.1016/j.matdes.2018.02.009CrossRef

23.

Farias, I., Olmos, L., Jimenez, O., Vergara-Hernández, H.J., Bouvard, D., Gárnica, P., Flores, M.: Analyzing the compressive behavior of porous Ti6Al4V by X-ray microtomography. Mater. Res-Ibero-AM J. 20(6), 1511–1517 (2017). https://doi.org/10.1590/1980-5373-mr-2017-0510CrossRef

24.

Olmos, L., Bouvard, D., Cabezas-Villa, J.L., Lemus-Ruiz, J., Jiménez, O., Arteaga, D.: Analysis of compression and permeability behavior of porous Ti6Al4V by computed microtomography. Met. Mater. Int. 25(3), 669–682 (2019). https://doi.org/10.1007/s12540-018-00223-wCrossRef

25.

Mihalcea, E., Hernández, H.V., Olmos, L., Jimenez, O.: Semi-solid sintering of Ti6Al4V/CoCrMo composites for biomedical applications. Mater. Res-Ibero-AM J. 22(2), e20180391 (2019). https://doi.org/10.1590/1980-5373-mr-2018-0391CrossRef

26.

Van Grieken, R., Markowicz, A. (eds.): Handbook of X-ray Spectrometry. CRC Press (2001)

27.

Okuma, G., Kadowaki, D., Shinoda, Y., Akatsu, T., Guillon, O., Wakai, F.: Determination of the size of representative volume element for viscous sintering. J. Ceram. Soc. Jpn. 124(4), 421–425 (2016). https://doi.org/10.2109/jcersj2.15275CrossRef

28.

Lin, C.L., Miller, J.D.: 3D characterization and analysis of particle shape using X-ray microtomography (XMT). Powder Tech. 154(1), 61–69 (2005). https://doi.org/10.1016/j.powtec.2005.04.031CrossRef

29.

Olmos, L., Martin, C.L., Bouvard, D., Bellet, D., Di Michiel, M.: Investigation of the sintering of heterogeneous powder systems by synchrotron microtomography and discrete element simulation. J. Am. Ceram. Soc. 92(7), 1492–1499 (2009). https://doi.org/10.1111/j.1551-2916.2009.03037.xCrossRef

30.

Marmottant, A., Salvo, L., Martin, C.L., Mortensen, A.: Coordination measurements in compacted NaCl irregular powders using X-ray microtomography. J. Eur. Ceram. Soc. 28(13), 2441–2449 (2008). https://doi.org/10.1016/j.jeurceramsoc.2008.03.041CrossRef

31.

Olmos, L., Chaix, J.M., Nadler, S., Bonnefoy, O., Gelet, J.L., Thomas, G.: Study by X-ray microtomography of the horizontal vibration effects on sand densification. Granul. Matter. 18(3), 61 (2016). https://doi.org/10.1007/s10035-016-0661-xCrossRef

32.

Saltykov, S.A.: Stereometrische Metallographie Metallurgizdat. VEB, Leipzig (1974)

33.

Yan, Z., Martin, C.L., Guillon, O., Bouvard, D.: Effect of size and homogeneity of rigid inclusions on the sintering of composites. Scr. Mater. 69(4), 327–330 (2013). https://doi.org/10.1016/j.scriptamat.2013.05.013CrossRef

34.

Kingery, W.D., Narasimhan, M.D.: Densification during sintering in the presence of a liquid phase II. Experimental. J Appl. Phys 30(3), 307–310 (1959). https://doi.org/10.1063/1.1735156CrossRef

Titel: X-ray Computed Microtomography Characterization of Ti6Al4V/CoCrMo Biomedical Composite Fabricated by Semi-solid Sintering
verfasst von: E. Mihalcea
H. J. Vergara-Hernández
L. Olmos
O. Jimenez
D. Arteaga
J. M. Salgado-López
Publikationsdatum: 01.03.2021
Verlag: Springer US
Erschienen in: Journal of Nondestructive Evaluation / Ausgabe 1/2021
Print ISSN: 0195-9298
Elektronische ISSN: 1573-4862
DOI: https://doi.org/10.1007/s10921-020-00742-w

Premium Partner

Marktübersichten

Die im Laufe eines Jahres in der „adhäsion“ veröffentlichten Marktübersichten helfen Anwendern verschiedenster Branchen, sich einen gezielten Überblick über Lieferantenangebote zu verschaffen.

Zur Marktübersicht

Springer Professional

Abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 1/2021

Ultrasonic and Optical Evaluation of Deformation Stages from the Beginning to Fracture: A Case Study of Low-Carbon Steels

Experimentation for Sag and Dimension Measurement of Thin-Walled Tubes and Pipes Using Multi-Channel Ultrasonic Imaging System

Convolutional Neural Networks for Semantic Segmentation as a Tool for Multiclass Face Analysis in Thermal Infrared

Augmented Ultrasonic Data for Machine Learning

Machine Learning Based Preprocessing to Ensure Validity of Cross-Correlated Ultrasound Signals for Time-of-Flight Measurements

Speckle Interferometric Investigation of Argon Pressure-Induced Surface Roughness Modifications in RF-Sputtered MoO3 Film

Premium Partner

Marktübersichten