nach oben

Journal of Material Cycles and Waste Management

Erschienen in:

17.10.2022 | ORIGINAL ARTICLE

Research on recycle of waste fluorescent lamp glasses and use as mineral filler in asphalt mixture

verfasst von: Rostam Ali Anwari, Sezen Coskun, Mehmet Saltan

Erschienen in: Journal of Material Cycles and Waste Management | Ausgabe 1/2023

Einloggen

Aktivieren Sie unsere intelligente Suche, um passende Fachinhalte oder Patente zu finden.

search-config

KI-gestützte Suche

Aus

Abstract

In this study, utilization of waste fluorescent lamp as mineral filler in asphalt mixture was investigated. The phosphorus powder of fluorescent lamps was removed by sieving and washing of the samples. Toxicity of waste lamps was investigated. Glass sample was used in the ratio of 25%, 50%, 75% and 100% to mineral filler. Optimum bitumen ratio was determined using super-pave mixing method which requires volumetric properties of the mixtures. Finally, indirect tensile tests were carried out on the dry and wet samples. Results of toxicity test indicated that glass of waste lamp was not classified as hazardous waste after washing. Indirect tensile test show that dry resistance values of the sample containing waste glass were similar to control sample. However, after the samples were conditioned, indirect tensile test show that wet values were significantly decreased by increasing glass content. As a result, when the glass of waste fluorescent lamp was used as mineral filler, the asphalt mixtures became more sensitive to moisture. Since this sensitivity will not be important, it is recommended to use waste fluorescent lamp glasses as a mineral filler for the “binder layer” that is not directly exposed to contact with water.

Graphical abstract

Vorheriger Artikel A novel mechanical plant compression system for biomass fuel and acquisition of squeezed liquid with water-soluble lignin as anti-virus materials

Nächster Artikel Synthesis of high-quality graphene sheets via decomposition of non-condensable gases from pyrolysis of polypropylene waste using unsupported Fe, Co, and Fe–Co catalysts

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

Jetzt informieren

Nur mit Berechtigung zugänglich

Coskun S (2021) Effect of the Covid-19 pandemic period on zero waste awareness: a scale development survey in Turkey. Glob Nest J. 23:581–589. https://doi.org/10.30955/gnj.004152CrossRef

Mallum I, MohdSam ARM, Lim NHAS, Omolayo N (2021) Sustainable utilization of waste glass in concrete: a review. SILICON. https://doi.org/10.1007/s12633-021-01152-xCrossRef

Wu S, Yang W, Xue Y (2004) Preparation and properties of glass-asphalt concrete. Key laboratory for silicate materials science and engineering of ministry of education, Wuhan University of Technology, Wuhan

Coskun S, Civelekoglu G (2015) Recovery of mercury from spent fluorescent lamps via oxidative leaching and cementation. Water Air Soil Pollut 226(6):1–13. https://doi.org/10.1007/s11270-015-2391-9CrossRef

Lee CH, Popuri SR, Peng YH, Fang SS, Lin K, Fan KS, Chang TC (2015) Overview on industrial recycling technologies and management strategies of end-of-life fluorescent lamps in Taiwan and other developed countries. J Mater Cycles Waste Manag 17:312–323CrossRef

Novais RM, Ascensao G, Sebra MP, Labrincha JA (2016) Waste glass from end-of-life fluorescent lamps as raw material in geopolymers. Waste Manag 52:245–255. https://doi.org/10.1016/j.wasman.2016.04.003CrossRef

Wang C, Wang H, Cao Y (2019) Waste printed circuit boards as novel potential engineered catalyst for catalytic degradation of orange II. J Clean Prod 221:234–241CrossRef

Wagner TP (2011) Compact fluorescent lights and the impact of convenience and knowledge on recycling rates. Waste Manag 31:1300–1306CrossRef

Smocovich MC (2000) Emergencias químicas provocadas por mercurio y sus compuestos: su prevención y control. Tesis por la Universidad Nacional de General San Martín

10.

Wong CSC, Duzgoren-Aydin N, Aydin A, Wong MH (2006) Sources and trends of environmental mercury emissions in Asia. Sci Total Enrivon 368:649–662CrossRef

11.

Diez S (2009) Human health effects of methylmercury exposure. Rev Environ Contam and Toxicol 198:111–132. https://doi.org/10.1007/978-0-387-09647-6_3CrossRef

12.

United Nations Environment Programme (2019). Minamata Convention on mercury text and annexes. https://www.mercuryconvention.org/sites/default/files/2021-06/Minamata-Conventionbooklet-Sep2019-EN.pdf

13.

Yorifuji T, Tsuda T, Inoue S, Takao S, Harada M, Kawachi I (2013) Critical appraisal of the 1977 diagnostic criteria for Minamata Disease. Arch Environ Occup H 68(1):22–29CrossRef

14.

Harada M, Hanada M, Tajiri M, Inoue Y, Hotta N, Fujino T (2011) Mercury poisoning in first nations groups in Ontario, Canada: 35 years of Minamata disease in Canada. J Minamata Stud 3:3–30

15.

NEMA (2000) Environmental impact analysis: spent mercury-containing lamps, 4th edn. NEMA, Rosslyn

16.

Truesdale RS, Beaulieu SM, Pierson TK (1993) Management of used fluorescent lamps: preliminary risk assessment. Final report. Research Triangle Institute, USA.

17.

Jang M, Hong SM, Park JK (2005) Characterization and recovery of mercury from spent fluorescent lamps. Waste Manag 25:5–14CrossRef

18.

Rey-Raap N, Gallardo A (2012) Determination of mercury distribution inside spent compact fluorescent lamps by atomic absorption spectrometry. Waste Manag 32:944–948. https://doi.org/10.1016/j.wasman.2011.12.001CrossRef

19.

Pitarch AM, Reig L, Gallardo A, Soriano L, Borrachero MV, Rochina S (2021) Reutilisation of hazardous spent fluorescent lamps glass waste as supplementary cementitious material. Constr Build Mater 292:123424. https://doi.org/10.1016/j.conbuildmat.2021.123424CrossRef

20.

USEPA (2007) Fluorescent lamp disposal and recycling in EPA Region 2 A guide for businesses in NJ, NY, PR and VI. https://www3.epa.gov/region02/waste/spent-lamp.pdf

21.

Coskun S, Ozgur C, Guncan A, Coskunsu S, Civelekoglu G (2014) Management of mercury risk originated from spent fluorescent lamps in Turkey. Conference: 4th international conference on industrial and hazardous waste management, Chaina, Crete, Greece

22.

Durão WA, Castro CA, Windmöller CC (2008) Mercury reduction studies to facilitate the thermal decontam-ination of phosphor powder residues from spent fluorescent lamps. Waste Manag 28:2311–2319CrossRef

23.

Tamanna N, Sutan NM, Lee DTC, Yakub İB (2013) Utilization of waste glass in concrete. 6th international engineering conference, energy and environment (ENCON 2013), Kuching, Sarawak, Malaysia

24.

Sharifi NP, Jafferji H, Reynolds SE, Blanchard MG, Sakulich AR (2016) Application of lightweight aggregate and rice husk ash to incorporate phase change materials into cementitious materials. J Sustain Cem -Based Mater 5(6):349–369. https://doi.org/10.1080/21650373.2016.1207576CrossRef

25.

Wartman J, Grubb DG, Nasim ASM (2004) Select engineering characteristics of crushed glass. J Mater Civ Eng 16(6):526. https://doi.org/10.1061/(ASCE)0899-1561(2004)16:6(526)CrossRef

26.

Nichols JC, Lay, J (2002) Crushed glass in macadam for binder course and road base layers. Proceedings of 4th European symposium on performance of bituminous and hydraulic materials in pavements, BITMAT 4, University of Nottingham, U.K., 11–12 April 2002, A.A.Balkema Publishers, Netherlands pp. 197–212

27.

Su N, Chen JS (2002) Engineering properties of asphalt concrete made with recycled glass. Resour Conserv Recycl 35(4):259–274. https://doi.org/10.1016/S0921-3449(02)00007-1CrossRef

28.

Wu SP, Yang WF, Xue YJ (2003) Design and preparation of steel slag SMA. J Wuhan Univ Technol-Mat Sci Edit 18(3):86–88CrossRef

29.

Jony HH, Al-Rubaie MF, Jahad IY (2011) The effect of using glass powder filler on hot asphalt concrete mixtures properties. Eng Tech Journal 29(1):44–57

30.

Saltan M, Uz V, Betul O (2015) Use of glass waste as mineral filler in hot mix asphalt. Sci Eng Compos 22(3):271–277. https://doi.org/10.1515/secm-2013-0135CrossRef

31.

Arabani M, Mirabdolazimi SM, Ferdowsi B (2012) Modeling the fatigue behaviors of glasphalt mixtures. Sci Iran 19(3):341–345. https://doi.org/10.1016/j.scient.2012.02.021CrossRef

32.

Paul D, Suresh M, Pal M (2021) Utilization of fly ash and glass powder as fillers in steel slag asphalt mixtures. Case Stud Constr Mater 15:e00672. https://doi.org/10.1016/j.cscm.2021.e00672CrossRef

33.

Ogundipe OM, Nnochiri ES (2020) Evaluation of the effects of waste glass in asphalt concrete using the Marshall test. Eng Rev 40(2):24–33. https://doi.org/10.30765/er.40.2.04CrossRef

34.

Simone A, Mazzotta F, Eskandarsefat S, Sangiorgi C, Vignali V, Lantieri C, Dondi G (2017) Experimental application of waste glass powder filler in recycled dense-graded asphalt mixtures. Road Mater Pavement Des 20:592–607. https://doi.org/10.1080/14680629.2017.1407818CrossRef

35.

Wijesekara RGS, Navarro R, Matsumura M (2011) Removal and recovery of mercury from used fluorescent lamp glass by pyrolysis. J Natl Sci Found 39(3):235–324. https://doi.org/10.4038/jnsfsr.v39i3.3627CrossRef

36.

Coskun S, Civelekoglu G (2014) Characterisation of waste fluorescent lamps to investigate their potential recovery in Turkey. Int J Glob Warm 6(2/3):140–148. https://doi.org/10.1504/IJGW.2014.061004CrossRef

37.

Raap NR, Gallardo A (2013) Removal of mercury bonded in residual glass from spent fluorescent lamps. J Environ Manage 115:175–178. https://doi.org/10.1016/j.jenvman.2012.11.012CrossRef

38.

Rhee SW, Choi HH, Park HS (2013) Performance evaluation of material separation from spent fluorescent lamps using the thermal end-cutting method. J Mater Cycles Waste Manag 15:503–509. https://doi.org/10.1007/s10163-013-0172-3CrossRef

39.

Choi Y, Rhee SW (2017) Evaluation of energy consumption in the mercury treatment of phosphor powder from spent fluorescent lamps using a thermal process. Sustainability 9(11):2013CrossRef

40.

Gedik A, Selcuk S, Lav AH (2021) Investigation of recycled fluorescent lamps waste as mineral filler in highway construction: a case of asphaltic pavement layers. Resour Conserv Recycl 168:106290CrossRef

41.

Republic of Turkey Ministry of Environment, Urbanization and Climate (2019) Hazardous waste licensed companies. https://eizin.cevre.gov.tr/Rapor/BelgeArama.aspx. Accessed 26 Feb 2019

42.

Coskun S (2013) Mercury recovery from waste fluorescent lamps and process optimization. Dissertation, Sulayman Demirel University

43.

Raposo C, Windmöller CC, Durao WA (2003) Mercury speciation in fluorescent lamps by thermal release analysis. Waste Manag 23(10):870–886. https://doi.org/10.1016/S0956-053X(03)00089-8CrossRef

44.

USEPA (1992) Toxicity characteristic leaching procedure (TCLP), Method 1311. USEPA Web Publishing. https://www.epa.gov/sites/default/files/2015-12/documents/1311.pdf. Accessed 15 Feb 2020

45.

Li Y, Jin L (2011) Environmental release of mercury from broken compact fluorescent lamps. Environ Eng Sci 28(10):5. https://doi.org/10.1089/ees.2011.0027CrossRef

46.

Ozgur C, Coskun S, Guncan A, Civelekoglu G (2014) Investigation of the recovery potential of mercury from spent tubular fluorescent lamps by electrowinning process. Fresenius Environ Bull 23(12A):3199–3201

47.

ASTM C 128-88 (1992) Test method for specific gravity and adsorption of fine aggregate. Annual Book of ASTM Standards, USA

48.

ASTM D854-10 (2010) Standard methods for specific gravity of soils by water pycnometer. ASTM International, West Conshohocken

49.

TS 118 EN 1426 (2002) Bitümler ve bitümlü bağlayıcılar – İğne batma derinliği tayini. Türk Standartları Enstitüsü, Ankara

50.

TS 119 (1964) Bitümlü maddelerin duktilite deneyi için metot. Türk Standartları Enstitüsü, Ankara

51.

TS 120 EN 1427 (2002) Bitümler ve bitümlü bağlayıcılar- Yumuşama noktası tayini–Halka ve bilya metodu. Türk Standartları Enstitüsü, Ankara

52.

TS EN 15326 (2010) Bitüm ve bitümlü bağlayıcılar-Yoğunluk ve özgül kütle tayini-Kapiler kapaklı piknometre yöntemi, Türk Standartları Enstitüsü, Ankara

53.

Karahancer S, Eriskin E, Capali B, Saltan M, Terzi S (2018) Superpave volumetric mix design of hot mix asphalt: case study of Isparta. J Eng Res Des 6(1):108–117. https://doi.org/10.21923/jesd.306098CrossRef

54.

Vavrik WR, Carpenter SH (1998) Calculating voids at a specified number of gyrations in the superpave gyratory compactor. In: Transportation Research Record 1630, TRB. National Research Council, Washington

55.

Tam WO (2005) The handbook of highway engineering. Texas

56.

Bonaquist R, Christensen DW (2005) Practical procedure for developing dynamic modulus master curves for pavement structural design. Trans Res Rec 1929:208–217. https://doi.org/10.1177/0361198105192900CrossRef

57.

DeVol JR, Krause JK, Laughlin SP, Willoughby K, McLean I (2007) Superpave gyratory compactor internal angle of gyration study. No. WA-RD 677.1. Washington State Department of Transportation, Olympia

58.

AASHTO T283 (2011) Standard method of test for resistance of compacted asphalt mixtures to moisture-ınduced damage. American Association of State and Highway Transportation Officials. Washington, DC

59.

Ahmadzade P, Altaş T, Geçkil T, (2008) Asfalt betonun siyah karbonun filler olarak kullanımı. IMO Teknik Dergi 297:4493–4507

60.

Aucott M, McLinden M, Winka M (2003) Release of mercury from broken fluorescent bulbs. J Air Waste Manag Assoc 53:143–151. https://doi.org/10.1080/10473289.2003.10466132CrossRef

61.

Occupational Safety and Health Administration (2000). Title 29. Code of Federal Regulations, Part 1910.1000, OSHA Table Z-2. U.S. Government Printing Office, Washington, DC

62.

Umar F, Ağar E (1994) Road pavement. İstanbul Technical University, Civil Engineering Faculty Publications, 1st Edn. İstanbul, Turkey

63.

Gurer C, Selman GS (2016) Investigation of properties of asphalt concrete containing boron waste as mineral filler. Mater Sci-Medzg 22(1):118–125. https://doi.org/10.5755/j01.ms.22.1.12596CrossRef

64.

Arabani M, Hamedi GH (2011) Using the surface free energy method to evaluate the effects of polymeric aggregate treatment on moisture damage in hot mix asphalt. J Mater Civ Eng 23(6):802–818CrossRef

65.

Choudhary J, Kumar B, Gupta A (2020) Utilization of solid waste materials as alternative fillers in asphalt mixes: a review. Constr Build Mater 234:117271. https://doi.org/10.1016/j.conbuildmat.2019.117271CrossRef

66.

Choudhary J, Kumar B, Gupta A (2021) Utilization of waste glass powder and glass composite fillers in asphalt pavements. Adv Civ Eng. https://doi.org/10.1155/2021/3235223CrossRef

67.

Sanij HK, Meybodi PA, Hormozaky MA, Hosseini SH, Olazar M (2019) Evaluation of performance and moisture sensitivity of glass-containing warm mix asphalt modified with zycothermTM as an anti-stripping additive. Constr Build Mater 197:185–194. https://doi.org/10.1016/j.conbuildmat.2018.11.190CrossRef

68.

Carteret RD, Comport L, Metcalf J, Rebbechi J (2009) Guide to pavement technology part 8: Pavement Construction. https://austroads.com.au/publications/pavement/agpt11/media/AGPT08-09_Guide_to_Pavement_ Technology_Part_8_Pavement_Construction.pdf ISBN 978-1-921551-58-1.

69.

Yu H, Deng G, Wang D, Zhang Z, Oeser M (2020) Warm asphalt rubber: a sustainable way for waste tire rubber recycling. J Cent South Univ 27(11):3477–3498CrossRef

70.

Zhao Y, Li G, Li T, Wang H, Zhang S, Zhang Y (2021) Performance and mechanism of solid waste coking sulfur paste modified asphalt mixture before and after curing. J Cent of South Univ 28(7):2179–2192CrossRef

71.

Asari M, Fukui K, Sakai S (2008) Life-cycle flow of mercury and recycling scenario of fluorescent lamps in Japan. Sci Total Environ 393(1):1CrossRef

72.

Sahin CK, Solak EB, Sava B, Onay BA (2022) Case study of Egirdir zero waste park for living and learning. Eur J Appl Sci 10(4):591–603

Titel: Research on recycle of waste fluorescent lamp glasses and use as mineral filler in asphalt mixture
verfasst von: Rostam Ali Anwari
Sezen Coskun
Mehmet Saltan
Publikationsdatum: 17.10.2022
Verlag: Springer Japan
Erschienen in: Journal of Material Cycles and Waste Management / Ausgabe 1/2023
Print ISSN: 1438-4957
Elektronische ISSN: 1611-8227
DOI: https://doi.org/10.1007/s10163-022-01525-3

Springer Professional

Abstract

Graphical abstract

Bitte loggen Sie sich ein, um Zugang zu Ihrer Lizenz zu erhalten.

Sie haben noch keine Lizenz? Dann Informieren Sie sich jetzt über unsere Produkte:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Weitere Artikel der Ausgabe 1/2023

Ferronickel slag as free-draining rockfill dike material: a novel waste solution for mining regions

Morphological study and performance deterioration of sustainable lignocellulosic corn fiber bio-composites

Extraction of keratin from keratinous wastes: current status and future directions

What makes residents more willing to participate in source separation of waste masks under the COVID-19 pandemic?

Infectious waste management in Japan: assessment of current trends in waste measurement and reporting in general and psychiatric hospitals

Eco-friendly recovery process of lithium from reduction roasting residue powder based on hydrothermal extraction