Top

Thermal Engineering

Published in:

01-06-2022 | HEAT AND MASS TRANSFER, PROPERTIES OF WORKING BODIES AND MATERIALS

Creation of Hydrophobic Functional Surfaces of Structural Materials on the Basis of Laser Ablation (Overview)

Authors: A. V. Ragutkin, M. R. Dasaev, O. V. Kalakutskaya, O. S. Zilova, E. S. Trushin

Published in: Thermal Engineering | Issue 6/2022

Activate our intelligent search to find suitable subject content or patents.

search-config

AI-assisted search

Off

Abstract

Over the past decade, interest has increased in controlling the wettability of metal surfaces with various liquids. In particular, the use of hydrophobic functional surfaces improves the efficiency and reliability of thermal power plants and systems operating in various areas of life. One of the most promising ways to achieve a hydrophobic state of structural materials is surface modification using laser equipment: laser ablation. As a result of exposure to laser radiation, melting, evaporation and recrystallization of the surface layer of the metal occur. By varying the parameters of exposure to laser radiation, it is possible to form a relief with specified geometric characteristics on a metal surface. The creation of hydrophobic metal surfaces using laser equipment includes the following steps: choosing the type of laser source, determining the radiation parameters and the trajectory of the laser beam over the surface, preparing the initial surface, forming the relief, and reducing the surface energy after laser ablation. This paper presents an overview of the results of research on the creation of hydrophobic metal surfaces based on the formation of a structured relief. In most studies, a relief was formed on the surface of metal samples in the form of equidistant lines, a grid, or had no pronounced structure (irregular structure). It has been established that the hydrophobic state of a metal surface with the highest contact angles (more than 150°) is achieved by laser texturing of the relief in the form of equidistant lines or a grid with a step not exceeding 100 μm. The maximum contact angle (approximately 179°) was obtained by forming a relief in the form of a grid with mutually perpendicular lines equidistant at 15 and 20 µm.

previous article Experimental and Numerical Studies into the Cavitation Impact of the Hydrofoil Surface with Different Treatments

next article High-Speed Passive Shut-Off Device for Shut-Off of Feed-Water Flow in a Brest-Type Reactor Facility in Accidents with Solidification of the Lead Coolant

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Online-Abonnement

Mit Springer Professional "Wirtschaft+Technik" erhalten Sie Zugriff auf:

über 102.000 Bücher
über 537 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Finance + Banking
Management + Führung
Marketing + Vertrieb
Maschinenbau + Werkstoffe
Versicherung + Risiko

Jetzt Wissensvorsprung sichern!

inform now

Springer Professional "Technik"

Online-Abonnement

Mit Springer Professional "Technik" erhalten Sie Zugriff auf:

über 67.000 Bücher
über 390 Zeitschriften

aus folgenden Fachgebieten:

Automobil + Motoren
Bauwesen + Immobilien
Business IT + Informatik
Elektrotechnik + Elektronik
Energie + Nachhaltigkeit
Maschinenbau + Werkstoffe

Jetzt Wissensvorsprung sichern!

inform now

T. Young, “An essay on the cohesion of fluids,” Philos. Trans. R. Soc. London 95, 65–87 (1805). https://doi.org/10.1098/rstl.1805.0005CrossRef

A. Rajappan, K. Golovin, B. Tobelmann, V. Pillutla, A. Abhijeet, W. Choi, A. Tuteja, and G. McKinley, “Influence of textural statistics on drag reduction by scalable, randomly rough superhydrophobic surfaces in turbulent flow,” Phys. Fluids 31, 042107 (2019). https://doi.org/10.1063/1.5090514CrossRef

R. N. Wenzel, “Resistance of solid surfaces to wetting by water,” Ind. Eng. Chem. 28, 988–994 (1936). https://doi.org/10.1021/IE50320A024CrossRef

A. B. D. Cassie and S. Baxter, “Wettability of porous surfaces,” Trans. Faraday Soc. 40, 546–551 (1944). https://doi.org/10.1039/tf9444000546CrossRef

A. V. Ryzhenkov, M. R. Dasaev, S. V. Grigoriev, A. V. Kurshakov, O. V. Ryzhenkov, and M. V. Lukin, “Hydrophobic brass surfaces created by means of multi-scale relief,” Int. J. Mech. Eng. Technol. 9 (12), 58–70 (2018).

A. I. Aguilar-Morales, S. Alamri, T. Kunze, and A. F. Lasagni, “Influence of processing parameters on surface texture homogeneity using Direct Laser Interference Patterning,” Opt. Laser Technol. 107, 216–227 (2018). https://doi.org/10.1016/j.optlastec.2018.05.044CrossRef

P. N. Belkin, S. A. Kusmanov, and E. V. Parfenov, “Mechanism and technological opportunity of plasma electrolytic polishing of metals and alloys surfaces,” Appl. Surf. Sci. Adv. 1, 100016 (2020). https://doi.org/10.1016/j.apsadv.2020.100016CrossRef

Z. Yang, X. Liu, and Y. Tian, “Novel metal-organic super-hydrophobic surface fabricated by nanosecond laser irradiation in solution,” Colloids Surf., A 587, 124343 (2020). https://doi.org/10.1016/j.colsurfa.2019.124343CrossRef

A. M. Kietzig, S. Hatzikiriakos, and P. Englezos, “Patterned superhydrophobic metallic surfaces,” Langmuir 25, 4821–4827 (2009). https://doi.org/10.1021/la8037582CrossRef

10.

B. Liu, W. Wang, G. Jiang, X. Mei, Z. Wang, K. Wang, and J. Cui, “Study on hierarchical structured PDMS for surface super-hydrophobicity using imprinting with ultrafast laser structured models,” Appl. Surf. Sci. 364, 528–538 (2016). https://doi.org/10.1016/j.apsusc.2015.12.190CrossRef

11.

A. Peter, A. H. A. Lutey, S. Faas, L. Romoli, V. Onuseit, and T. Graf, “Direct laser interference patterning of stainless steel by ultrashort pulses for antibacterial surfaces,” Opt. Laser Technol. 123, 105954 (2020). https://doi.org/10.1016/j.optlastec.2019.105954CrossRef

12.

G. Fiaschi, M. Lauro, A. Ballestrazzi, A. Rota, F. Biscarini, and S. Valeri, “Tribological response of laser-textured steel pins with low-dimensional micrometric patterns,” Tribol. Int. 149, 105548 (2020). https://doi.org/10.1016/j.triboint.2019.01.007CrossRef

13.

S. Milles, M. Soldera, B. Voisiat, and A. F. Lasagni, “Fabrication of superhydrophobic and ice-repellent surfaces on pure aluminium using single and multiscaled periodic textures,” Sci. Rep. 9, 13944 (2019). https://doi.org/10.1038/s41598-019-49615-xCrossRef

14.

A. H. A. Lutey, L. Gemini, and L. E. A. Romoli, “Towards laser-textured antibacterial surfaces,” Sci. Rep. 8, 10112 (2018). https://doi.org/10.1038/s41598-018-28454-2CrossRef

15.

A. M. Kietzig, M. N. Mirvakili, S. Kamal, P. Englezos, and S. G. Hatzikiriakos, “Laser-patterned super-hydrophobic pure metallic substrates: Cassie to Wenzel wetting transitions,” J. Adhes. Sci. Technol. 25, 2789–2809 (2015). https://doi.org/10.1163/016942410X549988CrossRef

16.

Z. Yang, Y. Tian, Y. Zhao, and C. Yang, “Study on the fabrication of super-hydrophobic surface on inconel alloy via nanosecond laser ablation,” Materials 12, 278 (2019). https://doi.org/10.3390/ma12020278CrossRef

17.

B. Wu, M. Zhou, J. Li, X. Ye, G. Li, and L. Cai, “Superhydrophobic surfaces fabricated by microstructuring of stainless steel using a femtosecond laser,” Appl. Surf. Sci. 256, 61–66 (2009). https://doi.org/10.1016/j.apsusc.2009.07.061CrossRef

18.

A. Garcia-Giron, J. M. Romano, A. Batal, B. Dashtbozorg, H. Dong, E. Martinez Solanas, D. Urrutia Angos, M. Walker, P. Penchev, and S. S. Dimov, “Durability and wear resistance of laser-textured hardened stainless steel surfaces with hydrophobic properties,” Langmuir 35, 5353–5363 (2019). https://doi.org/10.1021/acs.langmuir.9b00398CrossRef

19.

X. Li, Y. Jiang, Z. Jiang, Y. Li, C. Wen, and J. Lian, “Reversible wettability transition between superhydrophilicity and superhydrophobicity through alternate heating-reheating cycle on laser-ablated brass surface,” Appl. Surf. Sci. 492, 349–361 (2019). https://doi.org/10.1016/j.apsusc.2019.06.145CrossRef

20.

L. Qin, P. Lin, Y. Zhang, G. Dong, and Q. Zeng, “Influence of surface wettability on the tribological properties of laser textured Co–Cr–Mo alloy in aqueous bovine serum albumin solution,” Appl. Surf. Sci. 268, 79–86 (2013). https://doi.org/10.1016/j.apsusc.2012.12.003CrossRef

21.

X. Li, Q. Liu, and G. Dong, “Self-assembly membrane on textured surface for enhancing lubricity of graphene oxide nano-additive,” Appl. Surf. Sci. 505, 144572 (2020). https://doi.org/10.1016/j.apsusc.2019.144572CrossRef

22.

L. Jiao and S. K. Moon, “Laser induced hydrophobicity on the Ti6Al4V additive manufacturing parts,” in Proc. 3rd Int. Conf. on Progress in Additive Manufacturing, Singapore, May 14–17, 2018 (Nanyang Technological Univ., Singapore, 2018), pp. 493–497. https://doi.org/10.25341/D47C7D

23.

C. J. Yang, Y. C. Zhao, Y. L. Tian, F. J. Wang, X. P. Liu, and X. B. Jing, “Fabrication and stability investigation of bio-inspired superhydrophobic surface on nitinol alloy,” Colloids Surf., A 567, 16–26 (2019). https://doi.org/10.1016/j.colsurfa.2019.01.032CrossRef

24.

Y. L. Tian, Y. C. Zhao, C. J. Yang, F. J. Wang, X. P. Liu, and X. B. Jing, “Fabrication of bio-inspired nitinol alloy surface with tunable anisotropic wetting and high adhesive ability,” J. Colloid Interface Sci. 527, 328–338 (2018). https://doi.org/10.1016/j.jcis.2018.05.013CrossRef

25.

O. Raimbault, S. Benayoun, K. Anselme, C. Mauclair, T. Bourgade, A. M. Kietzig, P. L. Girard-Lauriault, S. Valette, and C. Donnet, “The effects of femtosecond laser-textured Ti–6Al–4V on wettability and cell response,” Mater. Sci. Eng.: C 69, 311–320 (2016). https://doi.org/10.1016/j.msec.2016.06.072CrossRef

26.

D. V. Zaitsev, K. A. Batishcheva, G. V. Kuznetsov, and E. G. Orlova, “Prediction of water droplet behavior on aluminum alloy surfaces modified by nanosecond laser pulses,” Surf. Coat. Technol. 399, 126206 (2020). https://doi.org/10.1016/j.surfcoat.2020.126206CrossRef

27.

B. Liu, K. Wang, W. Wang, X. Mei, and Z. Wang, “Preparation of super-hydrophobic surface on metal by picosecond laser pulses,” in Proc. Laser and Tera-Hertz Science and Technology [part of] International Photonics and Optoelectronics Meetings, Wuhan, China, Nov. 1–2, 2012 (Optical Society of America, Washington, DC, 2012), paper no. MF3B.1. https://doi.org/10.1364/LTST.2012.MF3B.1

28.

S. Milles, M. Soldera, T. Kuntze, and A. F. Lasagni, “Characterization of self-cleaning properties on superhydrophobic aluminum surfaces fabricated by direct laser writing and direct laser interference patterning,” Appl. Surf. Sci. 525, 146518 (2020). https://doi.org/10.1016/j.apsusc.2020.146518CrossRef

29.

S. Moradi, P. Englezos, and S. G. Hatzikiriakos, “Contact angle hysteresis: Surface morphology effects,” Colloid Polym. Sci. 291, 317–328 (2013). https://doi.org/10.1007/s00396-012-2746-3CrossRef

30.

K. A. Emelyanenko, S. N. Melnikov, P. I. Proshin, A. G. Domantovsky, A. M. Emelyanenko, and L. B. Boinovich, “Extreme-wettability textured materials for water collection from aerosols,” Dokl. Phys. Chem. 489, 478–482 (2019). https://doi.org/10.1134/S0012501619120017CrossRef

31.

M. Zrunek, Corrosion Protection of Metal Structures (Mechanical Engineering, Prague, 1984).

32.

L. Zhang, N. Lin, J. Zou, X. Lin, Z. Liu, S. Yuan, Y. Yu, Z. Wang, Q. Zeng, and W. Chen, “Super-hydrophobicity and corrosion resistance of laser surface textured AISI 304 stainless steel decorated with hexadecyltrimethoxysilane (HDTMS),” Opt. Laser Technol. 127, 106146 (2020). https://doi.org/10.1016/j.optlastec.2020.106146CrossRef

33.

F. P. Prakash, N. Jeyaprakash, M. Duraiselvam, G. Prabu, and C. H. Yang, “Droplet spreading and wettability of laser textured C-263 based nickel superalloy,” Surf. Coat. Technol. 397, 126055 (2020). https://doi.org/10.1016/j.surfcoat.2020.126055CrossRef

34.

A. Garcia-Giron, J. M. Romano, Y. Liang, B. Dashtbozorg, H. Dong, P. Penchev, and S. S. Dimov, “Combined surface hardening and laser patterning approach for functionalising stainless steel surfaces,” App-l. Surf. Sci. 439, 516–524 (2018). https://doi.org/10.1016/j.apsusc.2018.01.012CrossRef

35.

Z. Xia, Y. Xiao, Z. Yang, L. Li, S. Wang, X. Liu, and Y. Tian, “Droplet impact on the super-hydrophobic surface with micro-pillar arrays fabricated by hybrid laser ablation and silanization process,” Materials 12, 765 (2019). https://doi.org/10.3390/ma12050765CrossRef

36.

L. Liang, L. Lu, D. Xing, Z. Wan, and Y. Tang, “Preparation of superhydrophobic and anti-resin-adhesive surfaces with micro/nanoscale structures on high-speed steel via laser processing,” Surf. Coat Technol. 357, 57–68 (2019). https://doi.org/10.1016/j.surfcoat.2018.10.001CrossRef

37.

H. S. Maharana, R. Kumar, S. V. S. N. Murty, J. Ramkumar, and K. Mondal, “Surface micro-texturing of dual phase steel and copper by combining laser machining and electrochemical dissolution,” J. Mater. Proc. Technol. 273, 116260 (2019). https://doi.org/10.1016/j.jmatprotec.2019.116260CrossRef

38.

S. Moradi, S. Kamal, P. Englezos, and S. G. Hatzikiriakos, “Femtosecond laser irradiation of metallic surfaces: Effects of laser parameters on superhydrophobicity,” Nanotechnology 24, 415302 (2013). https://doi.org/10.1088/0957-4484/24/41/415302CrossRef

39.

X. Wang, C. Li, W. Hong, C. Ma, Y. Xing, and J. Feng, “Fabrication of ordered hierarchical structures on stainless steel by picosecond laser for modified wettability applications,” Opt. Express 26, 18998–19008 (2018). https://doi.org/10.1364/OE.26.018998CrossRef

40.

I. K. L. Kam and J. J. Neto, “Hydrophobic surface production by laser ablation on titanium alloy,” in Proc. Frontiers in Optics 2016, Washington, DC, Sept. 18–21, 2016 (Optical Society of America, Washington, DC, 2016). https://doi.org/10.1364/FIO.2016.JTh2A.109

41.

A. M. Kietzig, J. Lehr, L. Matus, and F. Liang, “Laser-induced patterns on metals and polymers for biomimetic surface engineering,” in Proc. 19th Laser Applications in Microelectronic and Optoelectronic Manufacturing (LAMOM), San Francisco, Cal., Feb. 1–6, 2014 (SPIE, Bellingham, Wash., 2014), in Ser.: Proceedings of SPIE, Vol. 8967, pp. 9–16, paper no. 896705. https://doi.org/10.1117/12.2042894

42.

B. Liu, W. Wang, G. Jiang, X. Mei, K. Wang, and J. Wang, “Formation of porous structure with subspot size under the irradiation of picosecond laser pulses,” J. Nanomater. 2013, 301301 (2013). https://doi.org/10.1155/2013/301301CrossRef

43.

X. Li, G. Wang, B. Zhan, S. Li, Z. Han, and Y. Liu, “A novel icephobic strategy: The fabrication of biomimetic coupling micropatterns of superwetting surface,” Adv. Mater. Interfaces 6, 1900864 (2019). https://doi.org/10.1002/admi.201900864CrossRef

44.

Y. Liu, X. Li, J. Jin, J. Liu, Y. Yan, Z. Han, and L. Ren, “Anti-icing property of bio-inspired micro-structure superhydrophobic surfaces and heat transfer model,” Appl. Surf. Sci. 400, 498–505 (2017). https://doi.org/10.1016/j.apsusc.2016.12.219CrossRef

45.

X. Li, G. Wang, F. S. Moita, C. Zhang, S. Wang, and Y. Liu, “Fabrication of bio-inspired non-fluorinated superhydrophobic surfaces with anti-icing property and its wettability transformation analysis,” Appl. Surf. Sci. 505, 144386 (2020). https://doi.org/10.1016/j.apsusc.2019.144386CrossRef

46.

S. Li, Y. Liu, Z. Zheng, X. Liu, H. Huang, Z. Han, and L. Ren, “Biomimetic robust superhydrophobic stainless-steel surfaces with antimicrobial activity and molecular dynamics simulation,” Chem. Eng. J. 372, 852–861 (2019). https://doi.org/10.1016/j.cej.2019.04.200CrossRef

47.

E. Armelin, S. Moradi, S. G. Hatzikiriakos, and C. Alemán, “Designing stainless steel surfaces with anti-pitting properties applying laser ablation and organofluorine coatings,” Adv. Eng. Mater. 20, 1700814 (2018). https://doi.org/10.1002/adem.201700814CrossRef

48.

S. Moradi, S. Kamal, and S. G. Hatzikiriakos, “Superhydrophobic laser-ablated stainless steel substrates exhibiting Cassie–Baxter stable state,” Surf. Innovations 3, 151–163 (2015). https://doi.org/10.1680/jsuin.15.00001CrossRef

49.

R. Jagdheesh, B. Pathiraj, E. Karatay, G. R. B. E. Römer, and A. Huis in‘t Veld, “Laser-induced nanoscale superhydrophobic structures on metal surfaces,” Langmuir 27, 8464–8469 (2011). https://doi.org/10.1021/la2011088CrossRef

50.

S. M. Razi, M. Mollabashi, and K. Madanipour, “Nanosecond laser surface patterning of bio Grade 316L stainless steel for controlling its wettability characteristics,” Int. J. Opt. Photonics 9, 43–52 (2015).

51.

M. Rafieazad, J. A. C. Jaffer, Cui, X. Duan, and A. Nasiri, “Nanosecond laser fabrication of hydrophobic stainless steel surfaces: The impact on microstructure and corrosion resistance,” Materials 11, 1577–1591 (2018). https://doi.org/10.3390/ma11091577CrossRef

52.

M. Tang, V. Shim, Z. Y. Pan, Y. S. Choo, and M. H. Hong, “Laser ablation of metal substrates for super-hydrophobic effect,” J. Laser Micro/Nanoeng. 6, 6–9 (2011). https://doi.org/10.2961/jlmn.2011.01.0002CrossRef

53.

Z. Pu, D. Zhang, X. Jing, Z. Yang, C. Yang, and K. F. Ehmann, “Fabrication of super-hydrophobic and highly oleophobic Ti–6Al–4V surfaces by a hybrid method,” Mater. Res. Bull. 130, 110915 (2020). https://doi.org/10.1016/j.materresbull.2020.110915CrossRef

54.

A. M. Kietzig, S. G. Hatzikiriakos, and P. Englezos, “Ice friction: The effects of surface roughness, structure, and hydrophobicity,” J. Appl. Phys. 106, 024303 (2009). https://doi.org/10.1063/1.3173346CrossRef

55.

K. M. Tanvir Ahmed and A. M. Kietzig, “Drag reduction on laser-patterned hierarchical superhydrophobic surfaces,” Soft Matter 12, 4912–4922 (2016). https://doi.org/10.1039/C6SM00436ACrossRef

56.

Y. Liu, S. Li, S. Niu, X. Cao, Z. Han, and L. Ren, “Bio-inspired micro-nano structured surface with structural color and anisotropic wettability on Cu substrate,” Appl. Surf. Sci. 379, 230–237 (2016). https://doi.org/10.1016/j.apsusc.2016.03.234CrossRef

57.

D. Li, H. Wang, D. Luo, Y. Liu, Z. Han, and L. Ren, “Corrosion resistance controllable of biomimetic superhydrophobic microstructured magnesium alloy by controlled adhesion,” Surf. Coat. Technol. 347, 173–180 (2018). https://doi.org/10.1016/j.surfcoat.2018.04.078CrossRef

58.

D. Wei, J. Wang, H. Wang, Y. Liu, S. Li, and D. Li, “Anti-corrosion behaviour of superwetting structured surfaces on Mg-9Al-1Zn magnesium alloy,” Appl. Surf. Sci. 483, 1017–1026 (2019). https://doi.org/10.1016/j.apsusc.2019.03.286CrossRef

59.

B. H. Luo, P. W. Shum, Z. F. Zhou, and K. Y. Li, “Surface geometrical model modification and contact angle prediction for the laser patterned steel surface,” Surf. Coat. Technol. 205, 2597–2604 (2010). https://doi.org/10.1016/j.surfcoat.2010.10.003CrossRef

60.

P. W. Shum, Z. F. Zhou, and K. Y. Li, “To increase the hydrophobicity, nonstickiness and wear resistance of DLC surface by surface texturing using a laser ablation process,” Tribol. Int. 78, 1–6 (2014). https://doi.org/10.1016/j.triboint.2014.04.026CrossRef

61.

B. H. Luo, P. W. Shum, Z. F. Zhou, and K. Y. Li, “Preparation of hydrophobic surface on steel by patterning using laser ablation process,” Surf. Coat. Technol. 204, 1180–1185 (2010). https://doi.org/10.1016/j.surfcoat.2009.10.043CrossRef

62.

G. V. Kuznetsov, D. V. Feoktistov, E. G. Orlova, K. Batishcheva, and S. S. Ilenok, “Unification of the textures formed on aluminum after laser treatment,” Appl. Surf. Sci. 469, 974–982 (2018). https://doi.org/10.1016/j.apsusc.2018.11.046CrossRef

63.

P. W. Shum, Z. F. Zhou, and K. Y. Li, “To increase the hydrophobicity and wear resistance of diamond-like carbon coatings by surface texturing using laser ablation process,” Thin Solid Films 544, 472–476 (2013). https://doi.org/10.1016/j.tsf.2013.02.075CrossRef

64.

G. V. Kuznetsov, D. V. Feoktistov, E. G. Orlova, I. Y. Zykov, and A. G. Islamova, “Droplet state and mechanism of contact line movement on laser-textured aluminum alloy surfaces,” J. Colloid Interface Sci. 553, 557–566 (2019). https://doi.org/10.1016/j.jcis.2019.06.059CrossRef

65.

A. I. Gavrilov, D. V. Golovin, A. M. Emelyanenko, D. A. Zayarny, A. A. Ionin, S. I. Kudryashov, S. V. Makarov, P. N. Saltuganov, and L. B. Boinovich, “Nano and microstructuring of materials’ surfaces using femtosecond laser pulses,” Bull. Russ. Acad. Sci.: Phys. 80, 358–361 (2016). https://doi.org/10.3103/S1062873816040122CrossRef

66.

Y. Cai, W. Chang, X. Luo, A. M. L. Sousa, K. H. A. Lau, and Y. Qin, “Superhydrophobic structures on 316L stainless steel surfaces machined by nanosecond pulsed laser,” Precis. Eng. 52, 266–275 (2018). https://doi.org/10.1016/j.precisioneng.2018.01.004CrossRef

67.

Y. Cai, X. Luo, Z. Xu, K. H. A. Lau, F. Ding, and Y. Qin, “A hybrid laser ablation and chemical etching process for manufacturing nature-inspired anisotropic superhydrophobic structures,” in Proc. EUSPEN’s 19th Int. Conf. and Exhibition, Bilbao, Spain, June 3–7, 2019 (EUSPEN, Bedford, UK, 2019).

68.

S. Milles, B. Voisiat, M. Nitschke, and A. F. Lasagni, “Influence of roughness achieved by periodic structures on the wettability of aluminum using direct laser writing and direct laser interference patterning technology,” J. Mater. Process. Technol. 270, 142–151 (2019). https://doi.org/10.1016/j.jmatprotec.2019.02.023CrossRef

69.

A. I. Aguilar-Morales, S. Alamri, and A. F. Lasagni, “Micro-fabrication of high aspect ratio periodic structures on stainless steel by picosecond direct laser interference patterning,” J. Mater. Process. Technol. 252, 313–321 (2017). https://doi.org/10.1016/j.jmatprotec.2017.09.039CrossRef

70.

A. I. Aguilar-Morales, S. Alamri, B. Voisiat, T. Kunze, and A. F. Lasagni, “The role of the surface nano-roughness on the wettability performance of microstructured metallic surface using direct laser interference patterning,” Materials 12, 2737 (2019). https://doi.org/10.3390/ma12172737CrossRef

71.

X. Jing, Z. Pu, S. Zheng, F. Wang, and H. Qi, “Nanosecond laser induced microstructure features and effects thereof on the wettability in zirconia,” Ceramics Int. 46, 24173 (2020). https://doi.org/10.1016/j.ceramint.2020.06.197CrossRef

72.

X. Jing, C. Yang, S. Zheng, X. Chen, and Y. Zhao, “Investigation of wettability of zirconia by nanosecond laser treatment,” in Proc. IEEE Int. Conf. on Manipulation, Manufacturing and Measurement on the Nanoscale (3M-NANO), Hangzhou, China, Aug. 13–17, 2018 (IEEE, Piscataway, N.J., 2018), pp. 10–13. https://doi.org/10.1109/3M-NANO.2018.8552196

73.

Z. Pu, X. Jing, C. Yang, F. Wang, and K. F. Ehmann, “Wettability modification of zirconia by laser surface texturing and silanization,” Int. J. Appl. Ceramic Technol. 17, 2182–2192 (2020). https://doi.org/10.1111/ijac.13579CrossRef

74.

J. Li, J. Xu, Z. Lian, Z. Yu, and H. Yu, “Fabrication of antireflection surfaces with superhydrophobic property for titanium alloy by nanosecond laser irradiation,” Opt. Laser Technol. 126, 106129 (2020). https://doi.org/10.1016/j.optlastec.2020.106129CrossRef

75.

Y. Wang, C. Ke, T. Wu, X. Zhao, and R. Wang, “Nanosecond laser texturing with hexagonal honeycomb micro-structure on titanium for improved wettability and optical properties,” Optik 192, 162953 (2019). https://doi.org/10.1016/j.ijleo.2019.162953CrossRef

76.

D. Deng, W. Wan, Y. Xie, Q. Huang, and X. Chen, “Fabrication of porous copper surfaces by laser micromilling and their wetting properties,” Precis. Eng. 49, 428–439 (2017). https://doi.org/10.1016/j.precisioneng.2017.04.005CrossRef

77.

C. Zwahr, A. Welle, T. Weingärtner, C. Heinemann, B. Kruppke, N. Gulow, M. G. Holthaus, and A. Fabián Lasagni, “Ultrashort pulsed laser surface patterning of titanium to improve osseointegration of dental implants,” Adv. Eng. Mater. 21, 1900639 (2019). https://doi.org/10.1002/adem.201900639CrossRef

78.

L. B. Boinovich, A. M. Emelyanenko, A. D. Modestov, A. G. Domantovsky, A. A. Shiryaev, K. A. Emelyanenko, O. V. Dvoretskaya, and A. A. Ganne, “Corrosion behavior of superhydrophobic aluminum alloy in concentrated potassium halide solutions: When the specific anion effect is manifested,” Corros. Sci. 112, 517–527 (2016). https://doi.org/10.1016/j.corsci.2016.08.019CrossRef

79.

A. M. Emelyanenko, L. B. Boinovich, A. D. Modestov, A. G. Domantovsky, K. A. Emelyanenko, and O. V. Dvoretskaya, “Corrosion behavior of superhydrophobic coatings on aluminum-magnesium alloy in potassium iodide solutions,” J. Electrochem. Soc. 163, C659–C665 (2016). https://doi.org/10.1149/2.06781610jesCrossRef

80.

L. B. Boinovich, A. M. Emelyanenko, A. D. Modestov, A. G. Domantovsky, and K. A. Emelyanenko, “Synergistic effect of superhydrophobicity and oxidized layers on corrosion resistance of aluminum alloy surface textured by nanosecond laser treatment,” ACS Appl. Mater. Interfaces 7, 19500–19508 (2015). https://doi.org/10.1021/acsami.5b06217CrossRef

81.

K. A. Emelyanenko, N. A. Sanzharovsky, E. V. Chulkova, A. A. Ganne, A. M. Emelyanenko, and L. B. Boinovich, “Superhydrophobic corrosion resistant coatings for copper via IR nanosecond laser processing,” Mater. Res. Express 5, 115001 (2018). https://doi.org/10.1088/2053-1591/aadc16CrossRef

82.

L. B. Boinovich, E. B. Modin, A. V. Aleshkin, K. A. Emelyanenko, E. R. Zulkarneev, I. A. Kiseleva, A. L. Vasiliev, and A. M. Emelyanenko, “Effective antibacterial nanotextured surfaces based on extreme wettability and bacteriophage seeding,” ACS Appl. Nano Mater. 1, 1348–1359 (2018). https://doi.org/10.1021/acsanm.8b00090CrossRef

83.

M. Martínez-Calderon, A. Rodríguez, A. Dias Ponte, M. Gómez-Aranzadi, and S. M. Olaizola, “Femtosecond laser manufacturing of highly hydrophobic hierarchical structures fabricated by combining surface microstructures and LIPSS,” in Proc. Conf. on Lasers in Manufacturing, Munich, Germany, June 22–25, 2015 (Wissenschaftliche Gesellschaft Lasertechnik, 2015).

84.

K. Sun, H. Yang, W. Xue, A. He, D. Zhu, W. Liu, K. Adeyemi, and Y. Cao, “Anti-biofouling superhydrophobic surface fabricated by picosecond laser texturing of stainless steel,” Appl. Surf. Sci. 436, 263–267 (2017). https://doi.org/10.1016/j.apsusc.2017.12.012CrossRef

85.

R. Jagdheesh, “Fabrication of a superhydrophobic Al₂O₃ surface using picosecond laser pulses,” Langmuir 30, 12067–12073 (2014). https://doi.org/10.1021/la5033527CrossRef

86.

R. Jagdheesh, M. Diaz, S. Marimuthu, and J. L. Ocaña, “Robust fabrication of μ-patterns with tunable and durable wetting properties: Hydrophilic to ultrahydrophobic via a vacuum process,” J. Mater. Chem. A 5, 7125–7136 (2017). https://doi.org/10.1039/C7TA01385JCrossRef

87.

L. B. Boinovich, A. M. Emelyanenko, and K. A. Emelyanenko, “Effect of decanol vapors on the delay in water droplet crystallization on superhydrophobic substrates,” J. Phys. Chem. C 119, 8718–8724 (2015). https://doi.org/10.1021/acs.jpcc.5b00990CrossRef

88.

A. R. Sayfutdinova, A. M. Emelyanenko, and L. B. Boinovich, “Influence of dodecanol on wetting behavior of superhydrophobic surfaces,” Physicochem. Probl. Miner. Process. 54, 131–141 (2018). https://doi.org/10.5277/ppmp1834CrossRef

89.

A. D. Modestov, K. A. Emelyanenko, A. M. Emelyanenko, A. G. Domantovsky, and L. B. Boinovich, “Application of laser micro- and nanotexturing for the fabrication of superhydrophobic corrosion-resistant coatings on aluminum,” Russ. Chem. Bull. 65, 2607–2611 (2016). https://doi.org/10.1007/s11172-016-1625-3CrossRef

90.

D. Huerta-Murillo, A. I. Aguilar-Morales, S. Alamri, J. T. Cardoso, R. Jagdheesh, A. F. Lasagni, and J. L. Ocaña, “Fabrication of multi-scale periodic surface structures on Ti–6Al–4V by direct laser writing and direct laser interference patterning for modified wettability applications,” Opt. Lasers Eng. 98, 134–142 (2017). https://doi.org/10.1016/j.optlaseng.2017.06.017CrossRef

91.

Y. Shi, Z. Jiang, J. Cao, and K. F. Ehmann, “Texturing of metallic surfaces for superhydrophobicity by water jet guided laser micro-machining,” Appl. Surf. Sci. 500, 144286 (2019). https://doi.org/10.1016/j.apsusc.2019.144286CrossRef

92.

D. Huerta-Murillo, A. García-Girón, J. M. Romano, J. T. Cardoso, F. Cordovilla, M. Walker, S. S. Dimov, and J. L. Ocaña, “Wettability modification of laser-fabricated hierarchical surface structures in Ti–6Al–4V titanium alloy,” Appl. Surf. Sci. 463, 838–846 (2018). https://doi.org/10.1016/j.apsusc.2018.09.012CrossRef

93.

V. D. Ta, A. Dunn, T. J. Wasley, J. Li, R. W. Kay, J. Stringer, P. J. Smith, E. Esenturk, C. Connaughton, and J. D. Shephard, “Laser textured superhydrophobic surfaces and their applications for homogeneous spot deposition,” Appl. Surf. Sci. 365, 153–159 (2016). https://doi.org/10.1016/j.apsusc.2016.01.019CrossRef

94.

J. T. Cardoso, A. I. Aguilar-Morales, S. Alamri, D. Huerta-Murillo, F. Cordovilla, A. F. Lasagni, and J. L. Ocaña, “Superhydrophobicity on hierarchical periodic surface structures fabricated via direct laser writing and direct laser interference patterning on an aluminium alloy,” Opt. Lasers Eng. 111, 193–200 (2018). https://doi.org/10.1016/j.optlaseng.2018.08.005CrossRef

95.

J. L. Ocaña, D. Huerta-Murillo, A. F. Lasagni, A. I. Aguilar-Morales, S. Alamri, J. T. Cardoso, A. García-Beltrán, F. Cordovilla, and I. Angulo, “Modification of Ti6Al4V surface properties by combined DLW-DLIP hierarchical micro-nano structuring,” Adv. Opt. Technol. 9, 121–130 (2020). https://doi.org/10.1515/aot-2019-0071CrossRef

96.

J. T. Cardoso, A. Garcia-Girón, J. M. Romano, D. Huerta-Murillo, R. Jagdheesh, M. Walker, S. S. Dimov, and J. L. Ocaña, “Influence of ambient conditions on the evolution of wettability properties of an IR-, ns-laser textured aluminium alloy,” RSC Adv. 7, 39617–39627 (2017). https://doi.org/10.1039/C7RA07421BCrossRef

97.

V. Vercillo, S. Tonnicchia, J. M. Romano, A. García-Girón, A. I. Aguilar-Morales, S. Alamri, S. S. Dimov, T. Kunze, A. F. Lasagni, and E. Bonaccurso, “Design rules for laser-treated icephobic metallic surfaces for aeronautic applications,” Adv. Funct. Mater. 30, 1910268 (2020). https://doi.org/10.1002/adfm.201910268CrossRef

98.

S. Y. Misyura, “Dependence of wettability of microtextured wall on the heat and mass transfer: Simple estimates for convection and heat transfer,” Int. J. Mech. Sci. 170, 105353 (2019). https://doi.org/10.1016/j.ijmecsci.2019.105353CrossRef

99.

L. Boinovich and A. M. Emelyanenko, “The role of water vapor desublimation in the adhesion of an iced droplet to a superhydrophobic surface,” Langmuir 30, 12596–12601 (2014). https://doi.org/10.1021/la503447fCrossRef

100.

S. Zouaghi, T. Six, S. Bellayer, S. Moradi, S. G. Hatzikiriakos, T. Dargent, V. Thomy, Y. Coffinier, C. André, G. Delaplace, and M. Jimenez, “Antifouling biomimetic liquid-infused stainless steel: Application to dairy industrial processing,” ACS Appl. Mater. Interfaces 9, 26565–26573 (2017). https://doi.org/10.1021/acsami.7b06709CrossRef

101.

V. J. Rico, C. López-Santos, M. Villagrá, J. P. Espinós, G. F. de la Fuente, L. A. Angurel, A. Borrás, and A. González-Elipe, “Hydrophobicity, freezing delay and morphology of laser-treated aluminum surfaces,” Langmuir 35, 6483–6491 (2019). https://doi.org/10.1021/acs.langmuir.9b00457CrossRef

102.

G. B. Shirsath, K. Muralidhar, R. G. S. Pala, and J. Ramkumar, “Condensation of water vapor underneath an inclined hydrophobic textured surface machined by laser and electric discharge,” Appl. Surf. Sci. 484, 999–1009 (2019). https://doi.org/10.1016/j.apsusc.2019.04.076CrossRef

103.

K. Ravi, W. L. Sulen, C. Bernard, Y. Ichikawa, and K. Ogawa, “Fabrication of micro-/nano-structured super-hydrophobic fluorinated polymer coatings by cold-spray,” Surf. Coat. Technol. 373, 17–24 (2019). https://doi.org/10.1016/j.surfcoat.2019.05.078CrossRef

104.

M. Sharp, A. Rosowski, and P. French, “Nanosecond laser texturing of aluminium for control of wettability,” Proc. Industrial Laser Applications Symp. (ILAS 2015), Kenilworth, UK, Mar. 17–18, 2015 (SPIE, Bellingham, Wash., 2015), in Ser.: Proceedings of SPIE, Vol. 9567, paper no. 96570J. https://doi.org/10.1117/12.2179929

105.

P. Hauschwitz, R. Jagdheesh, D. Rostohar, J. Brajer, J. Kopeček, P. Jiříček, J. Houdková, and T. Mocek, “Nanostructure fabrication on the top of laser-made micropillars for enhancement of water repellence of aluminium alloy,” Mater. Lett. 256, 126601 (2019). https://doi.org/10.1016/j.matlet.2019.126601CrossRef

106.

L. B. Boinovich and A. M. Emelyanenko, “The behaviour of fluoro- and hydrocarbon surfactants used for fabrication of superhydrophobic coatings at solid/water interface,” Colloids Surf., A 481, 167–175 (2015). https://doi.org/10.1016/j.colsurfa.2015.05.003CrossRef

107.

P. Hauschwitz, R. Jagdheesh, D. Rostohar, J. Brajer, J. Kopeček, P. Jiřícek, J. Houdková, and T. Mocek, “Hydrophilic to ultrahydrophobic transition of Al 7075 by affordable ns fiber laser and vacuum processing,” Appl. Surf. Sci. 505, 144523 (2019). https://doi.org/10.1016/j.apsusc.2019.144523CrossRef

108.

K. A. Emel’yanenko, A. R. Saifutdinova, E. B. Modin, A. M. Emel’yanenko, and L. B. Boinovich, “Application of laser nanotexturing to impart desired functional properties to the material surface,” in Proc. 3rd Interdisciplinary Youth Scientific Forum with Int. Participation on New Materials, Moscow, Nov. 21–24, 2017 (Buki Vedi, Moscow, 2017), pp. 73–77.

109.

N. E. Sataeva, L. B. Boinovich, K. A. Emelyanenko, A. G. Domantovsky, and A. M. Emelyanenko, “Laser-assisted processing of aluminum alloy for the fabrication of superhydrophobic coatings withstanding multiple degradation factors,” Surf. Coatings Technol. 397, 125993 (2020). https://doi.org/10.1016/j.surfcoat.2020.125993CrossRef

110.

S. Y. Misyura, G. V. Kuznetsov, D. V. Feoktistov, R. S. Volkov, V. S. Morozov, and E. G. Orlova, “The influence of the surface microtexture on wettability properties and drop evaporation,” Surf. Coat. Technol. 375, 458–467 (2019). https://doi.org/10.1016/j.surfcoat.2019.07.058CrossRef

111.

S. Y. Misyura, P. A. Strizhak, R. S. Volkov, and V. S. Morozov, “The influence of the wall microtexture on functional properties and heat transfer,” J. Mol. Liq. 294, 111670 (2019). https://doi.org/10.1016/j.molliq.2019.111670CrossRef

112.

S. Y. Misyura, “Heat transfer and convection of evaporating sessile droplets in transition from superhydrophilic to superhydrophobic structured wall: Optimization of functional properties,” Int. Commun. Heat Mass Transfer 112, 104474 (2020). https://doi.org/10.1016/j.icheatmasstransfer.2019.104474CrossRef

113.

L. Jiao, Z. Chua, S. Moon, J. Song, G. Bi, and H. Zheng, “Femtosecond laser produced hydrophobic hierarchical structures on additive manufacturing parts,” Nanomaterials 8, 601 (2018). https://doi.org/10.3390/nano8080601CrossRef

114.

L. B. Boinovich, K. A. Emelyanenko, A. G. Domantovsky, E. V. Chulkova, A. A. Shiryaev, and A. M. Emelyanenko, “Pulsed laser induced triple layer copper oxide structure for durable polyfunctionality of superhydrophobic coatings,” Adv. Mater. Interfaces 5, 1801099 (2018). https://doi.org/10.1002/admi.201801099CrossRef

115.

Y. Cai, A. M. L. Sousa, K. H. A. Lau, W. Chang, and X. Luo, “Fabrication of hydrophobic structures by nanosecond pulse laser,” Project EU H2020 ITN MICROMAN “Process Fingerprint for Zero-defect Net-shape MICROMANufacturing” (2017). https://www. microman.mek.dtu.dk/

116.

Y. Cai, X. Luo, Z. Liu, Y. Qin, W. Chang, and Y.Sun, “Product and process fingerprint for nanosecond pulsed laser ablated superhydrophobic surface,” Micromachines 10, 177–182 (2019). https://doi.org/10.3390/mi10030177CrossRef

117.

Y. Cai, X. Luo, Y. Tian, R. M. M. Hasan, W. Chang, and Y. Qin, “Dynamic behaviours of water droplets impacting on laser ablated surfaces,” Colloids Surf., A 580, 123743 (2019). https://doi.org/10.1016/j.colsurfa.2019.123743CrossRef

118.

A. M. Emelyanenko, F. M. Shagieva, A. G. Domantovsky, and L. B. Boinovich, “Nanosecond laser micro- and nanotexturing for the design of a superhydrophobic coating robust against long-term contact with water, cavitation, and abrasion,” Appl. Surf. Sci. 332, 513–517 (2015). https://doi.org/10.1016/j.apsusc.2015.01.202CrossRef

119.

P. Hauschwitz, R. Bicistova, R. Jagdheesh, J. Brajer, and D. Rostohar, “Superhydrophobic stainless steel surface by two-step ns laser processing,” MM Sci. J. 2019, 3647–3651 (2019). https://doi.org/10.17973/MMSJ.2019_12_2019116

120.

A. Garcia-Giron, J. M. Romano, A. Batal, A. Michałek, P. Penchev, and S. S. Dimov, “Experimental investigation of processing disturbances in laser surface patterning,” Opt. Lasers Eng. 126, 105900 (2020). https://doi.org/10.1016/j.optlaseng.2019.105900CrossRef

121.

J. M. Romano, A. Garcia-Giron, P. Penchev, and S. Dimov, “Triangular laser-induced submicron textures for functionalising stainless steel surfaces,” Appl. Surf. Sci. 440, 162–169 (2018). https://doi.org/10.1016/j.apsusc.2018.01.086CrossRef

122.

N. G. Tran and D. M. Chun, “Simple and fast surface modification of nanosecond-pulse laser-textured stainless steel for robust superhydrophobic surfaces,” CIRP Ann. 69, 525–528 (2020). https://doi.org/10.1016/j.cirp.2020.04.012CrossRef

123.

C. V. Ngo and D. M. Chun, “Fast wettability transition from hydrophilic to superhydrophobic laser-textured stainless steel surfaces under low-temperature annealing,” Appl. Surf. Sci. 409, 232–240 (2017). https://doi.org/10.1016/j.apsusc.2017.03.038CrossRef

124.

L. Gao, W. Zhou, Y. Wang, S. Wang, C. Bai, S. Li, B. Liu, J. Wang, and Y. L. Li, “Fabrication of hydrophobic structures on stent by direct three-beam laser interference lithography,” Optik 127, 5211–5214 (2016). https://doi.org/10.1016/j.ijleo.2016.02.075CrossRef

125.

A. Samanta, Q. Wang, S. K. Shaw, and H. Ding, “Nanostructuring of laser textured surface to achieve superhydrophobicity on engineering metal surface,” J. Laser Appl. 31, 022515 (2019). https://doi.org/10.2351/7.0004122CrossRef

126.

A. F. Lasagni, S. Alamri, A. I. Aguilar-Morales, F. Rößler, B. Voisiat, and T. Kunze, “Biomimetic surface structuring using laser based interferometric methods,” Appl. Sci. 8, 1260 (2018). https://doi.org/10.3390/app8081260CrossRef

127.

A. Y. Vorobyev and C. Guo, “Multifunctional surfaces produced by femtosecond laser pulses,” J. Appl. Phys. 117, 033103 (2015). https://doi.org/10.1063/1.4905616CrossRef

128.

T. H. Dinh, C. V. Ngo, and D. M. Chun, “Controlling the wetting properties of superhydrophobic titanium surface fabricated by UV nanosecond-pulsed laser and heat treatment,” Nanomaterials 8, 766 (2018). https://doi.org/10.3390/nano8100766CrossRef

129.

C.-V. Ngo and D.-M. Chun, “Effect of heat treatment temperature on the wettability transition from hydrophilic to superhydrophobic on laser-ablated metallic surfaces,” Adv. Eng. Mater. 20, 1701086 (2018). https://doi.org/10.1002/adem.201701086CrossRef

130.

R. Jagdheesh, M. Diaz, S. Marimuthu, and J. L. Ocaña, “Hybrid laser and vacuum process for rapid ultrahydrophobic Ti-6Al-4 V surface formation,” Appl. Surf. Sci. 471, 759–766 (2019). https://doi.org/10.1016/j.apsusc.2018.12.047CrossRef

131.

V. Lang, B. Voisiat, and A. F. Lasagni, “High throughput direct laser interferential patterning of aluminum for fabrication of super hydrophobic surfaces,” Materials 12, 1484 (2019). https://doi.org/10.3390/ma12091484CrossRef

132.

C. V. Ngo and D. M. Chun, “Fabrication of un-coated transparent superhydrophobic sapphire surface using laser surface ablation and heat treatment,” CIRP Ann. 67, 571–574 (2018). https://doi.org/10.1016/j.cirp.2018.04.085CrossRef

133.

C. V. Ngo and D. M. Chun, “Control of laser-ablated aluminum surface wettability to superhydrophobic or superhydrophilic through simple heat treatment or water boiling post-processing,” Appl. Surf. Sci. 435, 974–982 (2017). https://doi.org/10.1016/j.apsusc.2017.11.185CrossRef

134.

J. L. Ocaña, R. Jagdheesh, and J. J. García-Ballesteros, “Direct generation of superhydrophobic microstructures in metals by UV laser sources in the nanosecond regime,” Adv. Opt. Technol. 5, 87–93 (2016). https://doi.org/10.1515/aot-2016-0002CrossRef

135.

L. R. De Lara, R. Jagdheesh, and J. L. Ocaña, “Corrosion resistance of laser patterned ultrahydrophobic aluminium surface,” Mater. Lett. 184, 100–103 (2016). https://doi.org/10.1016/j.matlet.2016.08.022CrossRef

136.

R. Jagdheesh, P. Hauschwitz, J. Mužík, J. Brajer, D. Rostohar, P. Jiříček, J. Kopeček, and T. Mocek, “Non-fluorinated superhydrophobic Al7075 aerospace alloy by laser processing,” Appl. Surf. Sci. 493, 287–293 (2019). https://doi.org/10.1016/j.apsusc.2019.07.035CrossRef

137.

D. M. Chun, C. V. Ngo, and K. M. Lee, “Fast fabrication of superhydrophobic metallic surface using nanosecond laser texturing and low-temperature annealing,” CIRP Ann. 65, 519–522 (2016). https://doi.org/10.1016/j.cirp.2016.04.019CrossRef

138.

C. Dong, Y. Gu, M. Zhong, L. Li, K. Sezer, M. Ma, and W. Liu, “Fabrication of superhydrophobic Cu surfaces with tunable regular micro and random nano-scale structures by hybrid laser texture and chemical etching,” J. Mater. Process. Technol. 211, 1234–1240 (2011). https://doi.org/10.1016/j.jmatprotec.2011.02.007CrossRef

139.

A. Carvalho, L. Cangueiro, V. Oliveira, R. Vilar, M. H. Fernandes, and F. J. Monteiro, “Femtosecond laser microstructured alumina toughened zirconia: A new strategy to improve osteogenic differentiation of hMSCs,” Appl. Surf. Sci. 435, 1237–1245 (2017). https://doi.org/10.1016/j.apsusc.2017.11.206CrossRef

140.

S. Moghtadernejad, M. Jadidi, K. M. T. Ahmmed, C. Lee, A. Dolatabadi, and A. M. Kietzig, “Experimental study of droplet shedding on laser-patterned substrates,” Phys. Fluids 31, 122107 (2019). https://doi.org/10.1063/1.5126048CrossRef

141.

E. J. Y. Ling, V. Uong, J. S. Renault-Crispo, A. M. Kietzig, and P. Servio, “Reducing ice adhesion on nonsmooth metallic surfaces: Wettability and topography effects,” ACS Appl. Mater. Interfaces 8, 8789–8800 (2016). https://doi.org/10.1021/acsami.6b00187CrossRef

142.

A. Carvalho, L. Grenho, M. H. Fernandes, A. Daskalova, A. Trifonov, I. Buchvarov, and F. J. Monteiro, “Femtosecond laser microstructuring of alumina toughened zirconia for surface functionalization of dental implants,” Ceram. Int. 46, 1383–1389 (2019). https://doi.org/10.1016/j.ceramint.2019.09.101CrossRef

143.

M. Tang, M. Hong, and Y. S. Choo, “Hydrophobic surface fabrication by laser micropatterning,” in Proc. 2008 IEEE PhotonicsGlobal@Singapore, Singapore, Dec. 8–11, 2008 (IEEE, Piscataway, N.J., 2008). https://doi.org/10.1109/IPGC.2008.4781512

144.

B. S. Yilbas, M. Khaled, N. Abu-Dheir, N. Aqeeli, and S. Z. Furquan, “Laser texturing of alumina surface for improved hydrophobicity,” Appl. Surf. Sci. 286, 161–170 (2013). https://doi.org/10.1016/j.apsusc.2013.09.040CrossRef

145.

B. S. Yilbas, H. Ali, A. Al-Sharafi, F. Al-Sulaiman, and C. Karatas, “Effect of environmental dust particles on laser textured yttria-stabilized zirconia surface in humid air ambient,” Opt. Laser Technol. 101, 388–396 (2017). https://doi.org/10.1016/j.optlastec.2017.11.052CrossRef

146.

B. S. Yilbas, H. Ali, M. Rizwan, and M. Kassas, “Laser treatment of a neodymium magnet and analysis of surface characteristics,” Opt. Laser Technol. 82, 191–198 (2016). https://doi.org/10.1016/j.optlastec.2016.03.003CrossRef

147.

B. S. Yilbas, C. Karatas, H. Karakoc, B. J. A. Aleem, S. Khan, and N. Al-Aqeeli, “Laser surface treatment of aluminum based composite mixed with B₄C particles,” Opt. Laser Technol. 66, 129–137 (2015). https://doi.org/10.1016/j.optlastec.2014.08.014CrossRef

148.

R. Jagdheesh, J. J. García-Ballesteros, and J. L. Ocaña, “One-step generation of ultrahydrophobic aluminum surface patterns by nanosecond lasers,” in Proc. Conf. on Lasers in Manufacturing, Munich, Germany, June 22–25, 2015 (Wissenschaftliche Gesellschaft Lasertechnik, 2015).

149.

R. Jagdheesh, J. J. García-Ballesteros, and J. L. Ocaña, “One-step fabrication of near superhydrophobic aluminum surface by nanosecond laser ablation,” Appl. Surf. Sci. 374, 2–11 (2016). https://doi.org/10.1016/j.apsusc.2015.06.104CrossRef

150.

L. Dong, Q. Liu, Y. Liu, W. Li, Z. Wang, and D. Li, “Effect of surface area on the wettability of dual micro- and nanostructures fabricated by laser interference lithography,” in Proc. Int. Conf. on Manipulation, Manufacturing and Measurement on the Nanoscale (3M-NANO), Changchun, China, Oct. 5–9, 2015 (IEEE, Piscataway, N.J., 2015), pp. 163–164. https://doi.org/10.1109/3M-NANO.2015.7425512

151.

R. Jagdheesh, M. Diaz, and J. L. Ocaña, “Bio inspired self-cleaning ultrahydrophobic aluminium surface by laser processing,” RSC Adv. 6, 72933–72941 (2016). https://doi.org/10.1039/c6ra12236aCrossRef

152.

E. G. Orlova, D. V. Feoktistov, G. V. Kuznetsov, and K. O. Ponomarev, “Spreading of a distilled water droplet over polished and laser-treated aluminum surfaces,” Eur. J. Mech. B: Fluids 68, 118–127 (2017). https://doi.org/10.1016/j.euromechflu.2017.12.002MathSciNetCrossRef

153.

L. B. Boinovich, A. M. Emelyanenko, K. A. Emelyanenko, A. G. Domantovsky, and A. A. Shiryaev, “Comment on “Nanosecond laser textured superhydrophobic metallic surfaces and their chemical sensing applications” by Duong V. Ta, Andrew Dunn, Thomas J. Wasley, Robert W. Kay, Jonathan Stringer, Patrick J. Smith, Colm Connaughton, Jonathan D. Shephard (Appl. Surf. Sci. 357 (2015) 248–254),” Appl. Surf. Sci. 379, 111–113 (2016). https://doi.org/10.1016/j.apsusc.2016.04.056CrossRef

154.

R. Jagdheesh and J. L. Ocaña, “Laser machined ultralow water adhesion surface by low pressure processing,” Mater. Lett. 270, 127721 (2020). https://doi.org/10.1016/j.matlet.2020.127721CrossRef

Title: Creation of Hydrophobic Functional Surfaces of Structural Materials on the Basis of Laser Ablation (Overview)
Authors: A. V. Ragutkin
M. R. Dasaev
O. V. Kalakutskaya
O. S. Zilova
E. S. Trushin
Publication date: 01-06-2022
Publisher: Pleiades Publishing
Published in: Thermal Engineering / Issue 6/2022
Print ISSN: 0040-6015
Electronic ISSN: 1555-6301
DOI: https://doi.org/10.1134/S0040601522050056

Springer Professional

Abstract

Please log in to get access to your license.

Dont have a licence yet? Then find out more about our products and how to get one now:

Springer Professional "Wirtschaft+Technik"

Springer Professional "Technik"

Other articles of this Issue 6/2022

High-Speed Passive Shut-Off Device for Shut-Off of Feed-Water Flow in a Brest-Type Reactor Facility in Accidents with Solidification of the Lead Coolant

Analysis on the Technical Situation and Applied Difficulties of District Heating Load Forecasting

Results of Verification and Validation of the Oxid Module of the Euclid/V2 Integral Code in Part of Physicochemical Models of Processes in a Lead Coolant

Digitalization and Digital Transformation of the Thermal-Power Industry as a Factor of Improving the Thermal Infrastructure Efficiency (a Review)

Experimental and Numerical Studies into the Cavitation Impact of the Hydrofoil Surface with Different Treatments

Cofiring of Coal and Fossil Fuels is a Way to Decarbonization of Heat and Electricity Generation (Review)

Premium Partner